Using the evidence. A need for quantity, not quality?

The gene for alpha-stimulating guanine-nucleotide binding polypeptide, Gnas, has been considered as a candidate for the imprinting effects ascribed to distal mouse Chromosome (Chr) 2. Its human homologue (GNAS1) appears, from clinical and biochemical studies of patients with Albright hereditary osteodystrophy, to be paternally imprinted. GNAS1 maps to 20q13, a region that shows linkage conservation with distal mouse Chr 2. We have mapped Gnas within the imprinting region on distal Chr 2 by linkage analysis. To establish if Gnas is imprinted, we have looked for expression differences in tissues taken from mice carrying maternal duplication/paternal deficiency for distal Chr 2 (MatDp2) and its reciprocal (PatDp2). RNA in situ hybridization revealed high levels of Gnas mRNA in glomeruli of PatDp2 embryos at late gestation and lower levels in glomeruli of MatDp2 embryos. These results strongly suggest that Gnas is maternally imprinted and suggest that the mouse gene may be imprinted in a manner opposite that predicted in human.     

A 4-MB on-chip L2 cache for a 90-nm 1.6-GHz 64-bit microprocessor

A 4-MB L2 data cache was implemented for a 64-bit 1.6-GHz SPARC(r) RISC microprocessor. Static sense amplifiers were used in the SRAM arrays and for global data repeaters, resulting in robust and flexible timing operation. Elimination of the global clock grid over the SRAM array saves power, enabled by combining the clock information with array select signals. Redundancy was implemented flexibly, with shift circuits outside the main data array for area efficiency. The chip integrates 315 million transistors and uses an 8-metal-layer 90-nm CMOS process.     

A four-channel 3.125-Gb/s/ch CMOS serial-link transceiver with a mixed-mode adaptive equalizer

This work presents a quad-channel serial-link transceiver providing a maximum full duplex raw data rate of 12.5Gb/s for a single 10-Gbit eXtended Attachment Unit Interface (XAUI) in a standard 0.18-/spl mu/m CMOS technology. To achieve low bit-error rate (BER) and high-speed operation, a mixed-mode least-mean-square (LMS) adaptive equalizer and a low-jitter delay-immune clock data recovery (CDR) circuit are used. The transceiver achieves BER lower than <4.5/spl times/10/sup -15/ while its transmitted data and recovered clock have a low jitter of 46 and 64 ps in peak-to-peak, respectively. The chip consumes 178 mW per each channel at 3.125-Gb/s/ch full duplex (TX/RX simultaneous) data rate from 1.8-V power supply.     

Effects of various post-treatments on carbon nanotube films for reliable field emission

In this report, the FE characteristics of carbon nanotubes (CNTs) treated using both thermal annealing and mechanical coatings on the as-grown CNTs systematically studied. It was found that in the high temperature annealed samples, CNTs were attacked at its root during annealing due to a small amount of oxygen, and were pulled out of the substrate in places after FE measurements because of the contact resistance. However, for the mechanically coated samples both with spin on glass (SOG) and polymethyl methacrylate (PMMA), CNTs were found to be nearly intact after FE measurements and showed reliable FE characteristics over repeatable voltage scan. The reliability of CNTs during FE could be owing to the strong adhesion of CNTs to the substrate both by SOG and PMMA coatings.     

The appropriateness of the systematic framework to develop diagnosis procedures of nuclear power plants—an experimental verification

It has been well recognized that a diagnosis procedure that allows operators to successfully identify the nature of an on-going event is inevitable for an effective and appropriate recovery. Unfortunately, studies for a framework that can suggest a unified and consistent process in constructing a serviceable diagnosis procedure seem to be scant. Thus, Park et al. have suggested a systematic framework that can be used to construct a useful diagnosis procedure. In addition, the diagnosis procedure that is currently in use at the reference nuclear power plant (NPP) is reformed in order to demonstrate the appropriateness of the suggested framework. However, the necessity of a well-designed experiment is proposed to confirm the appropriateness of the suggested framework.In this regard, in this study, an experiment is conducted using a full-scope simulator of the reference NPP. From the experiment, two sets of operators' diagnosis performance data are collected, and then they are compared to investigate the change of an operator's diagnosis performance with respect to two types of diagnosis procedures.As a result, it is shown that an operator's diagnosis performance is improved when the revised diagnosis procedure is used. Therefore, it is reasonable to conclude that the suggested framework is useful in constructing an effective diagnosis procedure.     

Fabrication of high current and low profile micromachined inductorwith laminated Ni/Fe core

A new process for the fabrication of high current and very low profile micromachined inductors has been developed. This process involves the combination of mechanical lamination and electrodeposition of copper windings by means of LIGA-like lithography through thick epoxy photoresists. The dimension of the fabricated inductor is 16 mm×19 mm×1 mm. The fabricated inductor has an inductance value of 1.2 μH with DC saturation current of 3 A and an electrical resistance of less than 30 mΩ at 10 kHz     

A novel phase noise reduction technique in oscillators usingdefected ground structure

A new technique to reduce the phase noise in microwave oscillators is developed using the resonant characteristic of the defected ground structure (DGS). Two kinds of oscillators have been designed and measured for the examination of the reduction of phase noise by the DGS. The first adopts the DGS section under the microstrip line at the gate circuit, while the second has only the conventional microstrip line. Measurement shows reduced phase noise by 10-15 dB in the oscillator with the DGS compared to the conventional one     

A study on the degree of deliberation and meditation of cyber poll respondents for nuclear-related decision making

Public participation is essential in each step of the nuclear-related decision-making process. Recently, the electronic systems using the Internet have become quite popular, and have emerged as a good medium for communicating with the public. In this study, a comprehensive utilization of electronic public participation was used to analyze public opinion on a given nuclear-related decision-making process. The degree of deliberation and meditation of the public participating in an electronic poll survey was evaluated, and the decision-making factors representing the personal characteristics of the poll respondents such as age, income, education, residence, degree of knowledge and concern were carefully incorporated when preparing the poll-survey questionnaire for its evaluation. Fuzzy analysis was used to assess and aggregate the responses to each decision-making factor. As a case study, this procedure was used to analyzing public opinion on the location of a low-level radioactive waste disposal facility on the campus of Seoul National University. The results show that there is a tendency of respondents who are on the negative side of the argument to be more deliberate and meditative in their decision-making process than those on the positive side. Knowledge and residence were found to be important decision-making factors.