Corrosion Condition Evaluation at Muddy Creek Bridge

Corrosion rates were measured at the exposed spots of rebars near three corners of Muddy Creek Bridge located in northern West Virginia using a 3LP device. Also, chloride contents of the concrete samples taken from the vicinity of the spots were analyzed using a wet chemical method that had been developed in this study. The average corrosion rate over the three spots was 4.66 mA/m2, which is in the range of corrosion damage possible in 10–15 years. The average chloride content of the concrete over the three spots was 703 parts per million (ppm), which is well above the threshold limit value of 260 ppm. Although the corrosion rate measurement method using a 3LP device is by manual operation, it is found to be reliable and effective, and, thus, recommended for future studies of this kind of research. The wet chemical method developed in this study is found to be effective.     

Floating-patch MEMS antennas on HRS substrate for millimetre-wave applications

Novel floating-patch micro-electro-mechanical system (MEMS) antennas are proposed for millimetre-wave applications. The floating-patch MEMS antennas are fabricated on a high resistivity silicon (HRS) substrate using surface micromachining technology. Simulation and experimental results for reflection coefficients and radiation patterns are presented.     

Effects of reducing and oxidizing atmospheres on the PTCR characteristics of porous n-BaTiO3 ceramics by adding polyethylene glycol

Donor doped BaTiO₃ (n-BaTiO₃) ceramics were fabricated by adding polyethylene glycol (PEG) at 20 wt %. The effects of reducing and oxidizing atmospheres on the PTCR characteristics of the porous n-BaTiO₃ ceramics were investigated. The PTCR characteristics of the porous n-BaTiO₃ ceramics is strongly affected by chemisorbed oxygen at the grain boundaries and are recovered as the atmosphere is changed from the reducing gas to oxidizing gas. The low room-temperature resistivity of the porous n-BaTiO₃ ceramics in reducing atmospheres may be caused by the decrease in potential barrier height, which originates from an increase in the number of electrons owing to the desorption of chemisorbed oxygen atoms at the grain boundaries. In addition, the high room-temperature resistivity of the porous n-BaTiO₃ ceramics in oxidizing atmospheres may be caused by the increase in potential barrier height, which results from the adsorption of chemisorbed oxygen atoms at the grain boundaries.     

Bias-temperature instabilities of polysilicon gate HfO/sub 2/ MOSFETs

Bias-temperature instabilities (BTI) of HfO/sub 2/ metal oxide semiconductor field effect transistors (MOSFETs) have been systematically studied for the first time. NMOS positive BTI (PBTI) exhibited a more significant V/sub t/ instability than that of PMOS negative BTI (NBTI), and limited the lifetime of HfO/sub 2/ MOSFETs. Although high-temperature forming gas annealing (HT-FGA) improved the interface quality by passivating the interfacial states with hydrogen, BTI behaviors were not strongly affected by the technique. Charge pumping measurements were extensively used to investigate the nature of the BTI degradation, and it was found that V/sub t/ degradation of NMOS PBTI was primarily caused by charge trapping in bulk HfO/sub 2/ rather than interfacial degradation. Deuterium (D/sub 2/) annealing was found to be an excellent technique to improve BTI immunity as well as to enhance the mobility of HfO/sub 2/ MOSFETs.     

Influence of aggregate content on the migration coefficient of concrete materials using electrochemical method

In order to investigate the effect of coarse aggregate content on the chloride ion migration coefficient of concrete, specimens with different coarse aggregate volume fractions and two water/cement (w/c) ratios of mortar matrix were used. The chloride ion migration coefficient of concrete is obtained using the electrochemical technique to accelerate chloride ion migration in cement-based material and the experimental results were plotted as a function of the fine aggregate volume fraction. The results are analyzed comparing experimental results and theoretical models that represent the concretes as three-phase composite materials. The three phases are the mortar matrix, the coarse aggregate, and the interfacial transition zone between the two. The chloride ion migration coefficient is used to assess the dilution, tortuosity, interfacial transition zone (ITZ) and, percolation effects of coarse aggregate in concrete. It appears that the dilution and tortuosity effects are a dominant factor affecting the chloride ion migration coefficient of concrete in the low volume fraction of coarse aggregate. As the volume fraction of coarse aggregate increases to 40 and 20% in concrete of w/c ratio 0.35 and 0.45, respectively, the ITZ with percolation effects are significantly.     

Robust Space Time Receiver for CDMA-based Antenna Arrays

In this paper, we propose a new robust code division multiple access (CDMA) receiver of which weight vector is obtained by projecting the effective spatio-temporal signature waveform onto the signal subspace of the data covariance matrix. We verified our proposed algorithm by the field measured data obtained with a custom-built wideband CDMA test-bed. It will be shown that the proposed algorithm is robust to the signal mismatch.     

Protective effects of green tea extracts (polyphenon E and EGCG) on human cervical lesions

We investigated clinical efficacy of green tea extracts (polyphenon E; poly E and (-)-epigallocatechin-3-gallate [EGCG]) delivered in a form of ointment or capsule in patients with human papilloma virus (HPV) infected cervical lesions. Fifty-one patients with cervical lesions (chronic cervicitis, mild dysplasia, moderate dysplasia and severe dysplasia) were divided into four groups, as compared with 39 untreated patients as a control. Poly E ointment was applied locally to 27 patients twice a week. For oral delivery, a 200 mg of poly E or EGCG capsule was taken orally every day for eight to 12 weeks. In the study, 20 out of 27 patients (74%) under poly E ointment therapy showed a response. Six out of eight patients under poly E ointment plus poly E capsule therapy (75%) showed a response, and three out of six patients (50%) under poly E capsule therapy showed a response. Six out of 10 patients (60%) under EGCG capsule therapy showed a response. Overall, a 69% response rate (35/51) was noted for treatment with green tea extracts, as compared with a 10% response rate (4/39) in untreated controls (P<0.05). Thus, the data collected here demonstrated that green tea extracts in a form of ointment and capsule are effective for treating cervical lesions, suggesting that green tea extracts can be a potential therapy regimen for patients with HPV infected cervical lesions.     

Multi-level simulation of metal-forming processes

The IBF has for some years made use of finite element programmes to solve metal-forming problems. In the course of this investigation, it has become evident that a problem-oriented adaptation of FEM simulation to the problem in hand is beneficial in terms of computation effort. The computation time for the process parameters is optimised in a multi-level simulation. At level 1 (global analysis) integral parameters such as the required force and required work are computed using a coarse FEM mesh. At level 2 (local analysis) an optimised number of elements is used to determine continuum mechanics parameters like stress, strain and temperature. Microscopic phenomena are simulated at level 3 (microscopic analysis), using special micro-material elements and thermodynamic models.     

A typed functional extension of logic programming

A logic language is suitable for specification if it is equipped with features for data abstraction and modularization. In this paper, an effective mechanism to incorporate function and type into logic programming is presented as the means to embed data abstraction mechanism into logic programming. This incorporation is essentially based on Horn clause logic with equality and a polymorphic type system that is an extension of Mycroft and O’Keefe’s system. This paper also presents an implementation based on Warren Abstract Machine (WAM) and shows the performance, along with a comparison with WAM.