A randomized double‐blind crossover study of indoor air filtration and acute changes in cardiorespiratory health in a First Nations community

Few studies have examined indoor air quality in First Nations communities and its impact on cardiorespiratory health. To address this need, we conducted a crossover study on a First Nations reserve in Manitoba, Canada, including 37 residents in 20 homes. Each home received an electrostatic air filter and a placebo filter for 1 week in random order, and lung function, blood pressure, and endothelial function measures were collected at the beginning and end of each week. Indoor air pollutants were monitored throughout the study period. Indoor PM_2.5 decreased substantially during air filter weeks relative to placebo (mean difference: 37 μg/m³, 95% CI: 10, 64) but remained approximately five times greater than outdoor concentrations owing to a high prevalence of indoor smoking. On average, air filter use was associated with a 217‐ml (95% CI: 23, 410) increase in forced expiratory volume in 1 s, a 7.9‐mm Hg (95% CI: ?17, 0.82) decrease in systolic blood pressure, and a 4.5‐mm Hg (95% CI: ?11, 2.4) decrease in diastolic blood pressure. Consistent inverse associations were also observed between indoor PM_2.5 and lung function. In general, our findings suggest that reducing indoor PM_2.5 may contribute to improved lung function in First Nations communities.     

Town and Country Planning in England's Northeast Section

Abstract

A SYMPOSIUM OF CURRENT PLANNING THEORY: Planning for America , By GEORGE B. GALLOWAY AND ASSOCIATES. Henry Holt and Co., New York; 713 pages, price $3.

A TEXTBOOK ON SUBDIVISION: Subdivision Regulations: An Analysis of Land Subdivision Control Practices. By HAROLD W. LAUTNER. Public Administration Service; 346 pages, price $3.75.

EMPLOYMENT IN THE REGIONAL DEVELOPMENT OF RESOURCES: Development of Resources and Stabilization of Employment in the United States. By THE NATIONAL RESOURCES PLANNING BOARD; 409 pages, price $1.20.     

Partnerships for disability-inclusive road development in Papua New Guinea: Unusual suspects and equivocal gains

This article examines how an action research partnership developed and then influenced social justice outcomes during a 3-year research project to promote disability-inclusive road development in Papua New Guinea. The purpose of this article is to reflect on possible reasons why this partnership obtained certain positive results and not others. By reflecting on how the partnership developed, transformed over time, engendered achievements and failures, and affected the individuals and organizations involved in it, I aim to contribute to the understanding of how collaborative research partnerships can better promote the rights of those who are often marginalized from public space and decision-making. In this case study, neo-colonialism and underlying tensions between engineering and social development “world views”, both within and between partners, affected both positive outcomes and lost opportunities in terms of improving the lives of people with disabilities.     

Poly(methyl methacrylate)‐grafted cellulose nanocrystals: One‐step synthesis,nanocomposite preparation,and characterization

Cellulose nanocrystals (CNCs) are ideal reinforcing agents for polymer nanocomposites because they are lightweight and nano‐sized with a large aspect ratio and high elastic modulus. To overcome the poor compatibility of hydrophilic CNCs in non‐polar composite matrices, we grafted poly(methyl methacrylate) (PMMA) from the surface of CNCs using an aqueous, one‐pot, free radical polymerization method with ceric ammonium nitrate as the initiator. The hybrid nanoparticles were characterized by CP/MAS NMR, X‐ray photoelectron spectroscopy, infrared spectroscopy, contact angle, thermogravimetric analysis, X‐ray diffraction, and atomic force microscopy. Spectroscopy demonstrates that 0.11 g/g (11 wt %) PMMA is grafted from the CNC surface, giving PMMA‐g‐CNCs, which are similar in size and crystallinity to unmodified CNCs but have an onset of thermal degradation 45 °C lower. Nanocomposites were prepared by compounding unmodified CNCs and PMMA‐g‐CNCs (0.0025–0.02 g/g (0.25–2 wt %) loading) with PMMA using melt mixing and wet ball milling. CNCs improved the performance of melt‐mixed nanocomposites at 0.02 g/g (2 wt %) loading compared to the PMMA control, while lower loadings of CNCs and all loadings of PMMA‐g‐CNCs did not. The difference in Young's modulus between unmodified CNC and polymer‐grafted CNC composites was generally insignificant. Overall, ball‐milled composites had inferior mechanical and rheological properties compared to melt‐mixed composites. Scanning electron microscopy showed aggregation in the samples with CNCs, but more pronounced aggregation with PMMA‐g‐CNCs. Despite improving interfacial compatibility between the nanoparticles and the matrix, the effect of PMMA‐g‐CNC aggregation and decreased thermal stability dominated the composite performance.     

Response of real-time black carbon mass instruments to mini-CAST soot

Soot is a climate forcer and a dangerous air pollutant that has been increasingly regulated. In aviation, regulatory measurements of soot mass concentration in the exhaust of aircraft turbine engines are to be based on measurements of black carbon (BC) calibrated to elemental carbon (EC) content of diffusion flame soot. The calibration soot must currently meet only one criterion: minimum EC to total carbon (TC) ratio of 0.8. However, not including soot properties other than the EC/TC ratio may potentially lead to discrepancies between different BC measurements. We studied the response of two instruments, the AVL Micro-Soot Sensor (MSS) and the Artium Laser-Induced Incandescence 300 (LII), to soot from two miniature combustion aerosol standard (mini-CAST) burners. By changing the air-fuel ratio, premixing nitrogen into the fuel, and using a catalytic stripper to remove volatile compounds, we produced a wide range of particle morphologies and EC contents. As the EC content decreased, both the instruments underreported the EC mass, but the LII diverged more severely. Upon closer investigation of eight conditions with EC/TC > 0.8, the LII underreporting was found independent of primary particle size, but increased with decreasing geometric mean diameter of the soot agglomerates. As the geometric mean diameter decreased from 160 nm to 50 nm, the differences between the LII and MSS increased from 15% to 50%. The results suggest that in addition to EC content, calibration procedures for the regulatory BC measurements may need to take particle size distributions into account.

© 2016 American Association for Aerosol Research     

Use of Steel Slag Leach Beds for the Treatment of Acid Mine Drainage

Steel slag from the Waylite steel-making plant in Bethlehem, Pennsylvania was leached with acidic mine drainage (AMD) of a known quality using an established laboratory procedure. Leaching continued for 60 cycles and leachates were collected after each cycle. Results indicated that the slag was very effective at neutralizing acidity. The AMD/slag leachates contained higher average concentrations of Ba, V, Mn, Cr, As, Ag, and Se and lower average concentrations of Sb, Fe, Zn, Be, Cd, Tl, Ni, Al, Cu, and Pb than the untreated AMD. Based on these tests, slag leach beds were constructed at the abandoned McCarty mine site in Preston County, West Virginia. The leach beds were constructed as slag check dams below limestone-lined settling basins. Acid water was captured in limestone channels and directed into basins to leach through the slag dams and discharge into a tributary of Beaver Creek. Since installation in October 2000, the system has been consistently producing net alkaline, pH 9 water. The treated water is still net alkaline and has a neutral pH after it encounters several other acidic seeps downstream.     

Fractality of tics as a quantitative assessment tool for Tourette syndrome

Tics manifest as brief, purposeless and unintentional movements or noises that, for many individuals, can be suppressed temporarily with effort. Previous work has hypothesized that the chaotic temporal nature of tics could possess an inherent fractality, that is, have neighbour-to-neighbour correlation at all levels of timescale. However, demonstrating this phenomenon has eluded researchers for more than two decades, primarily because of the challenges associated with estimating the scale-invariant, power law exponent—called the fractal dimension D_f—from fractional Brownian noise. Here, we confirm this hypothesis and establish the fractality of tics by examining two tic time series datasets collected 6–12 months apart in children with tics, using random walk models and directional statistics. We find that D_f is correlated with tic severity as measured by the YGTTS total tic score, and that D_f is a sensitive parameter in examining the effect of several tic suppression conditions on the tic time series. Our findings pave the way for using the fractal nature of tics as a robust quantitative tool for estimating tic severity and treatment effectiveness, as well as a possible marker for differentiating typical from functional tics.     

A cathode support structure for use in a magnetron oscillator experiment

A low temperature co-fired ceramic (LTCC) material system has been used to develop a protype field emission cathode structure for use in an experimental magnetron oscillator. The structure is designed for used with 30 gated field emission array (GFEA) die electrically connected through silver metal traces and electrical vias. To approximate a cylinder, the cathode structure (48 mm long and 13.7 mm in diameter) is comprised of 10 faceted plates which cover the GFEA dies. Slits in the facet plates allow electron injection. The GFEA die (3 mm × 8 mm) are placed in axial columns of 3 and spaced azimuthally around a cylindrical support structure in a staggered configuration resulting in 10 azimuthal locations. LTCC manufacturing techniques were developed in order to fabricate the newly designed cathode with seven layers wrapped to form the cylinder with electrical traces and vias. Two different cathode wrapping techniques and two different via filling techniques were studied and compared. Two different facet plate manufacturing techniques were studied. Finally, four different support stand configurations for firing the cylindrical structure were also compared with a square post stand having the best circularity and linearity measurements of the fired structure.