含钒铁水中硅,钛含量对炼钢,炼铁工序指标的影响

利用生产实践数据，分析了铁水中Ｓｉ＋Ｔｉ含理对炼铁焦比、产量、生铁Ｓ以及提钒时的钒回收率、钒渣品位、白灰消耗等工序指标的影响，提出了适合于承钢铁水的Ｓｉ＋Ｔｉ含量。     

Ceramics based on mixed zirconium phosphate prepared by solar-furnace melting

A solar technology to synthesize an NZP structure using the example of Zr(PO₄) was developed. The method is based on high-temperature chemical reactions in the melt and subsequent crystallization of the hexagonal structure of the compounds of this class. Ceramic samples were prepared from the material obtained, and the processes of their sintering were studied.     

基于Web GIS的移民信息管理系统设计

基于在线地图服务,ArcGIS js for API提供的接口,以征地移民信息数据为基础,开发了基于Web GIS的移民信息管理系统.系统基于B/S架构,提供全面的地图操作、数据录入、红线内查询检索、汇总统计、综合分析等功能,实现移民实物指标调查数据的集中存储,确保数据处理的准确性,满足征地移民智能化管理的需要.     

Adaptive synchronization of master-slave large-scale systems against bias actuators and network attenuations

This paper utilizes the adaptive technique to design a class of active synchronizing masterslave large scale systems against imperfect actuators and networked interconnections with bias faults and signal attenuations, respectively. Without the requirement of knowledge of eventual faulty factors of bias-actuators on systems, and attenuation factors of connected networks, an adaptive mechanism is designed to estimate each unknown faulty factor on-line for constructing a class of distributed adaptive controllers. Then based on the adaptive adjustment parameters and Lyapunov stability theory, Lyapunov functions are addressed to prove that the proposed adaptive master-slave large-scale system can be guaranteed to be asymptotic synchronization with the improper actuator and faulty transmitted signals. Finally, a multiple vehicle large-scale system is used to verify the efficiency of the method.     

用数值模拟方法研究水驱特征曲线的结果

本文用数值模拟方法,按照大庆油田的油层条件,系统研究了水驱特征曲线的一般特征、出现直线段的时间及直线最小适用范围,同时重新评价了小井距试验区的水驱特征曲线,从而为在本油田正确使用水驱特征曲线提供了依据。文中用中期采油量倍增法估算的可采储量也可为开发决策提供参考数据。     

ZrB2-SiC基超高温陶瓷（UHTCs）的反应烧结及SHS粉体制备

用普通反应热压方法（RHP）和反应放电等离子体方法（R-SPS）原位反应制备了ZrB2-SiC，ZrB2-SiC—ZrC，ZrB2-SiC-ZrN，以及ZrB2-SiC-AIN4种复合材料。从密度，物相以及显微结构等方面比较了两种烧结方式之间的差别，对于升温速度较慢的普通热压方法，反应分步进行，显微结构不均匀；对于升温速度快的放电等离子体烧结，原料间的自蔓延反应被点着，反应速度快，显微结构均匀。同时以红外灯的热量为点火源，引发了Zr，Si及B4C间在空气气氛下的自蔓延反应，制备了较纯及粒径约为1μm的活性粉体。     

A study of the properties of ink-jet printed cotton fabric following low-temperature plasma treatment

This paper studies the effect of low-temperature plasma treatment on an ink-jet printed cotton fabric. Due to the specific printing and conductivity requirements for ink-jet printing, not all conventional printing chemicals, such as sodium alginate and urea, used for cotton fabric can be directly incorporated into the ink formulation. As a result, the cotton fabric requires pretreatment with the printing chemicals prior to the stage of ink-jet printing. Cotton is pretreated with the printing chemicals by means of a coating method. The aim of this paper was to study the possibility and effectiveness of applying low-temperature plasma treatment to enhance the performance of pretreatment paste containing sodium alginate so as to improve the properties of the ink-jet printed cotton fabric. Experimental results revealed that a low-temperature plasma pretreatment coupled with the ink-jet printing technique could improve the final printed properties of cotton fabric.     

纳米技术在涂料中的产业化应用

介绍了国内外纳米涂料的现状及其产业化进展。     

Orthogonal and fine lithographic structures attained from the next generation proton beam writing facility

A second generation proton beam writing (PBW) system has been built at the Centre for Ion Beam Applications at the National University of Singapore for fabrication of high aspect ratio 3D nano lithographic structures. System improvements and a few lithographic structures obtained with this facility are presented in this paper. Through accurate alignment of the magnetic quadrupole lenses and the electrostatic scanning system, orthogonal beam scanning has been achieved. The earlier constrain of limited beam scan area has been overcome by adopting a combination of beam and stage scanning as well as stitching. With these improvements smallest ever Ni structure of 65 nm in width has been fabricated using nickel electroplating on a proton beam written PMMA sample in the second generation PBW facility. Using this improved PBW facility, we have also demonstrated the fabrication of fine lithographic patterns with 19 nm line width and 60 nm spacing in 100 nm thick negative high resolution hydrogen silsesquioxane resist. Future possible system improvements leading to finer resolution will be discussed briefly.