Fuel modelling in fast reactor whole core accident calculations

Transient fuel pin behaviour and fuel motion models are of major importance for the analysis of the initiation phase of unprotected whole-core LOF and TOP accidents in LMFBRs. The role played by these models is highlighted by discussing LOF and TOP accident sequences. This is followed by an overview of present whole-core fuel pin behaviour and fuel motion models and also a critical evaluation of these models.     

Simulation of the initial stages of nucleation and growth of Au/NaCl(100)

The results of a computer simulation of the initial stages of the nucleation and growth of gold on NaCl(100) are presented. A potential energy scaling Monte Carlo model employing a 50 × 50 array, mobile monomers, dimers and trimers, and gold atom vertical “roll up” was used. The parameters in the model were obtained from the work of Robinson and Robins, other published sources and/or found by calculation. Simulations of the migration of single gold adatoms over the surface permitted the determination of the diffusion coefficient as a function of the reciprocal temperature which returned the same activation energy given by the potential field, thus indicating the consistency of the model. Initial cluster densities were determined using deposition rates of R_d = 10¹⁵cm^-2s^-1 and R_d = 10¹⁴cm^-2s^-1 over the temperature range T=200–425 K. Initial cluster growth was found to occur primarily by surface phase transport and resulted in clusters that were shaped like very thin disks. Using the equations from the work of Velfe and coworkers, calculations were made to extrapolate the computer simulation data in order to permit an indirect comparison with the data of Robinson and Robins. Good agreement was achieved. Initial condensation coefficients determined over a 250 ms interval showed that α ≈ 0 at T > 425 K and α ≈ 1 at T < 325 K for a deposition rate of R_d=10¹⁵ cm^-2 s^-1.     

Effects of flux enhancing polymer on the characteristics of sludge in membrane bioreactor process.

A newly developed membrane performance enhancer (MPE) was used to prevent membrane fouling in a membrane bioreactor (MBR) process. It transpired that 1,000 mg/l of MPE reduced polysaccharide levels from 41 mg/I to 21 mg/I on average under the experimental condition. Repeated experiments also confirmed that 50-1,000 mg/l of MPE could reduce membrane fouling significantly and increase the intervals between membrane cleanings. Depending on MPE dosages and experimental conditions, trans-membrane pressure (TMP) increase was suppressed for 20-30 days, while baseline TMP surged within a few days. In addition, MPE allowed MBR operation even at 50,000 mg/l of total solid and reduced permeate COD. However, no evidence of toxicity for sludge was found from respiratory works.     

An integrated system to remote monitor and control anaerobic wastewater treatment plants through the internet.

The TELEMAC project brings new methodologies from the Information and Science Technologies field to the world of water treatment. TELEMAC offers an advanced remote management system which adapts to most of the anaerobic wastewater treatment plants that do not benefit from a local expert in wastewater treatment. The TELEMAC system takes advantage of new sensors to better monitor the process dynamics and to run automatic controllers that stabilise the treatment plant, meet the depollution requirements and provide a biogas quality suitable for cogeneration. If the automatic system detects a failure which cannot be solved automatically or locally by a technician, then an expert from the TELEMAC Control Centre is contacted via the internet and manages the problem.     

A process-dependent real-time controller for sequencing batch reactor plants: results of full-scale operation.

This paper presents results of a research project, in which a process-dependent real-time control (RTC) strategy for a sequencing batch reactor plant was realised in full-scale. The cycle controller is based on NH4 analysers, NO3 probes, TSS probes and sludge level probes. With this new RTC strategy it was possible to increase the treatment capacity by 50%. By implementation of the new controller the TN, TP and NH4-N treatment efficiency could be improved significantly, too. The treatment efficiency concerning COD is comparable.     

Standby power system VRLA battery reserve life estimation scheme

This paper presents a valve-regulated lead acid (VRLA) battery reserve life estimation scheme. The scheme is adaptive in both type and frequency of involvement. The scheme is based on capacity trending with the support of a number of state-of-health (SOH) indicators. These SOH indicators include accumulated thermal stress, float voltage, and indicators acquired from the start-of-discharge (coup de fouet) region. An implementation test case is given, indicating that the scheme is capable of providing an accurate estimation of reserve life long before the end of life. Furthermore, the estimation accuracy improves as the end of battery life approaches.     

Learning with belief levels

We study learning of predicate logics formulas from “elementary facts,” i.e. from the values of the predicates in the given model. Several models of learning are considered, but most of our attention is paid to learning with belief levels. We propose an axiom system which describes what we consider to be a human scientist's natural behavior when trying to explore these elementary facts. It is proved that no such system can be complete. However we believe that our axiom system is “practically” complete. Theorems presented in the paper in some sense confirm our hypothesis.     

Integrating trust into the CyberCraft Initiative via the Trust Vectors model [Application Notes]

This research supports the hypothesis that the Trust Vector model can be modified to fit the CyberCraft Initiative, and that there are limits to the utility of historical data. This research proposed some modifications and expansions to the Trust Model Vector, and identified areas for future research.     

Modelling and simulation of KNbO3 ceramics dispersion

The dispersion of potassium niobate (KNbO₃) ceramics is analysed using the multiple-arc approach. This has revealed a high frequency arc that is unattainable by the Cole-Cole single arc analysis. The temperature dependence of the new arc is derived through the spread parameter of the relaxation distribution and interpreted in terms of the ferroelectric property of the KNbO₃ ceramics. It is shown that the overall dispersion behaviour of the ceramics is mainly due to the existence of two distinctly different polarisation mechanisms. The arc approach has also provided an effective tool for network simulation of dispersion whereby the ceramics are modelled by nine parallel R-C branches over the frequency range 10²-10⁵ Hz used