燃气管网动态仿真的研究及应用

研究和了解燃气在管道中的流动，是进行燃气管网系统优化和提高管网输运系统安全性的前提和基础。以流体力学三大守恒方程为基础，建立了等温和非等温条件下的燃气管网稳态和动态仿真理论模型。以有限差分法为基础，得到了上述模型的求解方法，并加入了耗散项，提高了求解方法的稳定性。通过增加初始点和延长出口点的方法，简化了模型的求解。通过在北京六环天然气管网中的初步应用，分别得到了与实际值综合相对误差为1.21％和2.62％的压力和流量仿真值，从而验证了模型及求解方法的可靠性。     

丙烯腈装置回收塔内聚合物生成原因的分析

针对丙烯腈生产过程中回收塔内聚合物堵塞降液管造成回收塔运行周期短的问题,通过对丙烯腈回收塔内各组分分布的模拟计算,直观显示了回收塔内各组分的浓度分布,发现了回收塔的聚合段与丙烯醛的富集段相吻合的现象,初步得出了回收塔内局部聚合的原因;通过对塔内聚合物的特性分析和评判,进一步证实了“回收塔内局部聚合严重是由于在聚合段丙烯醛聚集引起”这一现象;根据模拟计算结果和实际运行经验,提出了预防聚合物堵塞降液管的措施,并进行了部分生产验证,为丙烯腈生产企业延长装置运行周期提供了理论指导。     

一种零知识证明协议的安全分析与改进

论文指出了文献[1]中的零知识证明协议在公钥参数选取上的安全漏洞,并从求解离散对数的角度进行了分析证明。然后吸取了DSA数字签名算法中安全密钥选取高效简单的优点,提出了一种比Schnorr身份识别方案快1／3的简单、安全、高效的零知识证明身份识别方案。     

TUD-DNS3脱硝助剂在催化裂化装置的工业应用

TUD-DNS3脱硝助剂在中韩（武汉）石油化工有限公司1号催化裂化装置上进行了工业应用。结果表明：针对两段再生工艺，当系统中助剂占总催化剂藏量的质量分数为2.6%时，烟气脱硫装置外排污水中的氨氮质量浓度由加剂前的100 mg/L下降至40 mg/L以内；助剂的加入降低了CO焚烧炉的炉膛温度，有利于烟气的合格排放，并对装置操作、产品分布及汽油、柴油产品质量无不良影响。     

微制造平台微振动的最优控制

采用混合隔振技术建立了微制造平台隔振系统。该系统以空气弹簧和橡胶层作为被动隔振元件、超磁致伸缩致动器作为主动隔振元件，并采用最优控制理论设计其主动控制器。研究了在不同的性能指标加权阵的情况下，该主动振动控制系统对基础干扰和由微制造设备产生的直接干扰所引起的微制造平台振动的控制效果。研究表明性能指标加权阵对振动控制效果影响非常大。通过大量的仿真实验确定了一组性能指标加权阵，使所设计的主动控制系统能在较宽的频率范围对基础干扰和直接干扰所引起的微制造平台振动进行有效的控制。     

Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry     

DSP--数字化时代的基因芯片

DSP是当今发展最为迅速的和最有发展前景的技术之一。与普通CPU和MCU相比 ,DSP在数字信号处理方面有着无可比拟的优势 ,特别适合网络、通信、控制等需要进行大量数字信号处理的应用场合。今天DSP已经成为通信、计算机、网络、工业控制以及家用电器等电子产品中不可或缺的基础器件 ,DSP在通信、计算机、网络、工业控制以及消费类电子产品等领域有着非常广泛的应用 ,本文阐述了DSP的特点、应用和市场以及DSP技术的发展前景。     

Study of Disk-Loaded Waveguide Filled with Plasma

Recently disk-loaded waveguide has been widely used in high-power traveling wave tubes (HPTWT). It has been shown in many experiments that the interaction efficiency and output power can be increased greatly by injecting plasma into the vacuum microwave device. Using field analysis, the dispersion characteristics and the interaction impedance of the disk-loaded waveguide filled with plasma are analyzed in a strong longitudinal magnetic field. In conclusion, the frequency of the TM₀₁ mode increases as the density of the plasma increases. It also can be found when the plasma density increases to a large scale, the TM₀₁ mode of the disk-loaded waveguide overlaps the TG mode, these two modes couple each other and form the new hybrid modes.     

N-苄基丙烯酰胺的合成

以丙烯腈和苯甲醇为原料，浓硫酸作催化剂，合成了N-苄基丙烯酰胺（N-BAA）。考察了反应温度、反应时间和催化剂用量等因素对产物收率的影响，得出了最佳反应条件：n（丙烯腈）：n（苯甲醇）：n（浓硫酸）=3：1：1．2，反应时间3h，反应温度60℃。在最佳条件下，N-BAA的收率可达92％。每100g粗产物用10％氢氧化钠溶液提纯，精制产物纯度可达99．80％，熔点为64～65℃。通过红外光谱对产物结构进行了表征。     

Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry