The Moldflow system of computer aided polymer flow analysis

The problems associated with injection moulding are listed. The uses of the Moldflow program to assist in the practical solution of these are described.     

Simultaneous determination of proline and betaines by high performance liquid chromatography

A method is described for the simultaneous determination by reversed-phase h.p.l.c. of proline, glycinebetaine, trigonelline and stachydrine. The mobile phase was water containing 0.02M dibutylamine phosphate at pH 3.0. The compounds were separated in a Dextropak Radial-PAK Cartridge and were detected by a differential refractometer. Total time of elution was 8 min. The method was applied to the analysis of leaves of two tropical grasses and a tropical legume which had been subjected to water stress.     

Base metal Co-fired (Na,K)NbO3 structures with enhanced piezoelectric performance

A NaF-Nb₂O₅ flux doped (Na,K)NbO₃ (NKN) based lead-free ceramic was successfully co-fired with nickel inner electrodes in reduced atmospheres. No chemical reactions and/or inter-diffusion were detected at the interface between the nickel (Ni) electrodes and the NKN-based piezoelectrics. Dielectric, resistivity, and electromechanical performance were measured with processing under different firing conditions and flux additions to obtain high densities. Ceramics are obtained with submicron grain structures with the NaF-Nb₂O₅ sintering aids (2 and 4 wt%) fluxes, and high densities when firing at low pO₂ (10^?10 atms) atmospheres at sintering temperatures ~1150 °C for 2 hours. High resistivities and low losses can be obtained through a second annealing condition at 850 °C and 10^?7 atms at 8 hours. High d ₃₃ values (over 350 pm/V) determined under unipolar converse electromechanical measurements were obtained in the simple prototyped co-fired structures to show feasibility towards base metal electrodes in multilayer actuators.     

MECHANISMS OF DRYING OF SKIN-FORMING MATERIALS.III. DROPLETS OF NATURAL PRODUCTS.

ABSTRACT

Drying studies were carried out on single droplets suspended from a rotating nozzle in a horizontal wind tunnel. Droplets were of solution of a third type of skin-forming material, namely the natural products skim milk or fructose. Droplet weight and temperature were measured during the drying process. Dried crusts were recovered and examined by Scanning Electron Microscopy.

With this type of material a skin first forms at any drying condition on the surface of the droplet at a cerlain stage of drying. A crust subsequently forms beneath the skin. The final dried panicle retains the structure and properties of the original powder, unless the material is dried at very high temperatures. e.g. >300 °C. which result in burning.

An increase in air temperature resulted in the formation of a smoother skin offering a higher resistance to vapour diffusion. At temperatures over 100 °C droplets exhibited puffing or ballooning phenomena; i.e. they inflated and deflated many times before forming the final dried particles.     

Structural evolution of a Ta-filament during hot-wire chemical vapour deposition of Silicon investigated by electron backscatter diffraction

We report on the application of electron backscatter diffraction to investigate the structural changes of a tantalum filament operated at typical hot-wire chemical vapour deposition conditions for the synthesis of hydrogenated nanocrystalline silicon. Various tantalum-silicides, identified by electron backscatter diffraction, form preferentially along the length of the filament. The filament has a recrystallized Ta inner core and a TaSi₂ layer encapsulated with a Si layer at the cooler ends. The αTa₅Si₃, metastable Ta₅Si₃ and Ta₂Si phases formed in addition to recrystallized Ta and TaSi₂ at the centre regions. Cracks and porosity were prevalent throughout the length of the filament. The microstructural evolution of the aged tantalum filament can be ascribed to the thermal gradient along the filament length, recrystallization of Ta and the variation of silicon content within the filament.     

PRELIMINARY PHASE DIAGRAMS FOR BITUMEN/ HEAVY OILS AND RELATED MIXTURES

ABSTRACT

The phase behaviour of heavy oil mixtures was studied using an X-ray imaging system. Batch phase experiments were performed at temperatures and pressures up to 725 K and 7 MPa. Complex phase behaviour such as liquid-liquid-vapour and solid-liquid-liquid-vapour were observed and preliminary experimental phase diagrams were constructed. This observed complex phase behaviour is consistent with thermodynamic theory and such phase behaviour can be modelled using the Peng-Robinson equation of state and the tangent plane criterion. These latter points are illustrated through the phase diagram for a model reservoir fluid (ethane + propane + n-butane + phenanthrene) which exhibits solid-liquid-liquid-vapour phase behaviour. Example predicted and experimental phase diagrams are presented for this model system.     

Effect of Cr additions on the electrical properties of Ni–BaTiO3 ultra-thin multilayer capacitors

Multilayer ceramic capacitors based on BaTiO₃ dielectric compositions and Ni inner electrodes have complex interfacial reactions that impact the continuity of the inner electrode microstructure. Previously we demonstrated that through the addition of Cr to Ni, a significant improvement in the continuity of ultra-thin Ni electrodes in Ni–BaTiO₃ multilayer capacitors could be achieved. Here, the effect of the Cr addition to the nickel electrode pastes is studied with regard to the electrical properties. Low-field electrical measurements demonstrate no major differences between Cr doped Ni and undoped Ni. However, high-field measurements show a significant decrease to the total capacitor resistance. Under a critical electrical bias the conductivity significantly increases due to a Fowler–Nordheim tunneling conduction though the interfacial Schottky barrier at the dielectric–electrode interface; the onset voltage of this conduction is much lower than with the undoped nickel. Based on these results, we evaluate criteria for the selection of an appropriate refractory metal in order to improve the Ni electrode continuity.     

Automatic speech recognition in practice

There is a growing interest in the commercial possibilities offered by automatic speech recognition (ASR) technology. Unfortunately the prospective user has little independent guidance with respect to the potential success of any proposed implementation. There do exist a few general human factors guidelines on the use of ASR, but most of the corpus of knowledge that forms part of the lore within the ASR community is based on the unpublished experiences of system.developers and users themselves. The present paper attempts to redress this balance; it is a summary of the experiences of users and system designers at 30 research and commercial sites in the UK and USA where ASR has been extensively used or tested. The application represented were classified as vehicle, office, industrial, and aids for disabled people. A number of important human factors issues were identified, and the relative success of the various applications are discussed.