Microstrip reflectarray antenna with offset feed

The authors derive and verify the concept of antenna focusing by a planar 'microstrip reflectarray' antenna. Experimental results from schematically distributed patch radiators with microstrip delay lines are consistent with the simulation results. The advantages and disadvantages of such an antenna are described. The measured overall antenna efficiency is approximately 48% at scan angles up to 30 degrees . These results demonstrate the feasibility of such an antenna.<>     

Fourier-transform-limited pulses from gain-switched distributed-Bragg-reflector lasers using simultaneous modulation of gain and phase sections

Fourier-transform-limited pulses ( Delta tau . Delta nu approximately=0.35) have been obtained from a microwave-modulated DBR laser at 1.56 mu m. The chirp of the gain-switched pulse is compensated for by applying a fraction of the microwave signal to the phase section, thereby creating an instantaneous frequency shift of opposite sign. The generation of short coherent pulses from such a monolithic source can be of great interest for long haul soliton transmission.<>     

New wire interface for graded 3-D TLM

A new 3-D graded TLM model for thin radiating wires is presented. The model differs from previous TLM models because the wire is modelled at the interfaces between cells, rather than through the centre of the node. The connection between the TLM symmetrical condensed-node link lines and the line forms a 'wire interface'. The scattering algorithm for the interface and simulation results are given.<>     

Über die Eignung der Wechselbiegemaschine „WEBI”︁ zur Ermittlung von Ermüdungskennwerten

On Alternating Bending Machine WEBI's Suitability for Determination of Fatigue Characteristics Already in 1966, experimental investigations revealed that the flat bending torsion testing machine ?FLATO”? (Schenck, Darmstadt) doesn't keep constant its torsional moment amplitude in case of specimen's fatigue softening or hardening, respectively. Thus. conclusions concerning the material's fatigue characteristics drawn from such experimental results might therefore be seriously false. Furthermore, also the alternating bending testing machine ?WEBI”? (Schenck, Darmstadt) shows an equivalent behaviour concerning its bending moment amplitude. For this reason. the main findings of a comprehensive experimental study carried out on WEBI with an unalloyed steel C 45 (0.45 mass perccnl C) in different heat treatment conditions are reported in this paper.     

A novel technique for fabrication of metallic structures on polyimide by selective electroless copper plating using ion implantation

The successful use of palladium ion implantation into polyimide to seed an electroless plated film of copper on the polyimide surface is reported. Polyimide (Hitachi PIX 3400) was implanted with palladium ions to doses of 1.5 × 10¹⁵ − 1.2 × 10¹⁷ ions cm⁻² using a MEVVA ion implanter. The implanted ions acted as sites for nucleation of copper film. A copper film was then deposited on implanted polyimide using a commercial electroless plating solution. The ion energy was kept low enough to facilitate a low critical ‘seed’ threshold dose that was measured to be 3.6× 10¹⁶ Pd ions cm⁻². Test patterns were made using polyimide to study the adaptability of this technique to form thick structures. Plated films were studied with optical microscopy, Rutherford Backscattering Spectrometry (RBS) and Profilometry. The adhesion of films was qualitatively assessed by a ‘scotch tape test’. The film growth (thickness) was observed to be linear with plating time. A higher implantation dose led to greater plating rates. The adhesion was found to improve with increasing dose.     

Life quality index for the estimation of societal willingness-to-pay for safety

The engineering and management of human safety is an important societal objective that includes extensive efforts by governments, both legislative and administrative, to enhance the health and safety of the public. Although the achievement of safety goals depend primarily on individuals and organizations responsible for safety, much support is drawn from expertise in diverse scientific and engineering disciplines. The activities range from structural safety (dams, tunnels, bridges to tall buildings) to safe operation of hazardous industrial installations (energy generation facilities, LNG terminals, petrochemical plants) to transportation systems (airline, rail, car safety) to technologies designed to minimize adverse impacts on the environment. All these activities are crucially concerned with risk: with the likelihood and the probable effects of various measures on life and health. We have developed a unified rationale and a clear basis for effective strategic management of risk across diverse sectors. Safety is an important objective in society but it is not the only one. The allocation of society's resources devoted to safety must be continually appraised in light of competing needs, because there is a limit on the resources that can be expended to extend life. The paper presents the Life Quality Index (LQI) as a tool for the assessment of risk reduction initiatives that would support the public interest and enhance safety and quality of life. The paper provides an intuitive reformulation of the LQI as equivalent to a valid utility function that is consistent with the principles of rational decision analysis. The LQI is further refined to consider the issues of discounting of life years, competing background risks, and population age and mortality distribution. The LQI is applied to quantify the societal willingness-to-pay, which is an acceptable level of public expenditure in exchange for a reduction in the risk of death that results in improved life-quality.     

Manufacture of a high-quality alkylsalicylate additive at the Novokuibyshevsk Petroleum Refinery

Translated from Khimiya i Tekhnologiya Topliv i Masel, No. 4, pp. 16–17, April, 1992.