Ionic conductivity in poly(vinyl butyral) based polymeric electrolytes: Effect of solvents and salts

Li⁺ conductive solid polymeric electrolytes (SPEs) have been prepared by complexing Li salts LiX (X = I, SCN, CLO4, CF3SO3) with poly(vinyl butyral) (PVB) an amorphous polymer with a low T_g value and well known for its outstanding laminating properties. These self-supporting SPEs have been prepared by the solution cast technique using cyclohexanone, tetrahydrofuran, and n-butyl alcohol as solvents. The XRD and DSC investigations correlated to measured ionic conductivities have revealed that in addition to the amorphous nature of the resulting complex, its T_g value, the concentration and the values of the lattice energies of the complexing salts, the solvent used in making the SPEs also govern the value of ionic conductivity. Highest ionic conductivity values attained in SPEs made with n-butyl alcohol are explained in terms of the interception of the hydrogen bonding due to solvation.     

Electroluminescent zinc sulphide devices produced by sol-gel processing

Zinc sulphide thin film electroluminescent devices doped with Mn or Tb have been produced on p-type Si substrates using a process in which doped zinc oxide films are deposited by a sol-gel drain coating method from a solution of zinc acetate containing a manganese or terbium dopant. The films are then converted to ZnS by heating them in an atmosphere containing hydrogen sulphide which replaces the oxygyn with sulphur. The composition, crystalline structure and optical properties of films have shown that complete conversion from the oxide to the sulphide takes place. The luminescent characteristics of the devices so produced have been measured as a function of the doping concentrations, film thickness, insulator thickness and driving voltage and frequency. It has been found that yellow or green luminescence can be obtained using Mn or Tb doping respectively.     

Representing context, cognition, and crew performance in a shutdown risk assessment

This paper presents a potentially practical treatment of dynamic operator-system interactions. The approach employs a dynamic event tree framework to explicitly address plant dynamics, system indications, crew-plant interactions, time available, crew cognition, errors of commission (mistakes), and multiple planning and diagnosis possibilities. The approach is applied in an analysis of a hypothesize medium break loss of coolant accident for a test reactor that occurs during plant shutdown. This transient was selected on the basis of: a significant cognitive component being present, high consequences being associated with operator actions, and the importance of event timing to scenario progression. The results presented show how quantitative risk predictions are affected by the treatment of dynamics, and demonstrate how non-proceduralized recovery actions and a number of performance shaping factors (e.g., crew experience, stress, and confidence) can be explicitly treated. Insights and lessons learned regarding the performance of a dynamic assessment are also presented.     

Effect of beam voltage on the properties of aluminium nitride prepared by ion beam assisted deposition

The effects of nitrogen-beam voltage on the structure, stress, energy band gap and hardness of AIN thin films deposited on Si (111), Si (100) and sapphire (0001) by ion beam assisted deposition (IBAD) are reported. As the nitrogen-beam voltage was increased from 50 to 200 V, the stress and disorder in the AIN films increased as determined by X-ray diffraction, FTIR and Raman spectroscopy. The preferred orientation of the film's c-axis changed from completely normal to the film at 100 V, to a mixture of normal and in the plane of the film at 200 V. For AIN films deposited under the same conditions, the films were more highly oriented on sapphire (0001) than in Si (111). The hardness of the films increased from 18.2 to 23.7 GPa with the nitrogen-beam voltage, and possible reasons for this change in hardness are considered.     

Interfacing systems LOCA (ISLOCA) component pressure capacity methodology and typical plant results

A proposed methodology and sample results from several plant investigations are presented for evaluating the expected pressure capacity of nuclear power plant components which could potentially be subjected to Interfacing Systems LOCA (ISLOCA) conditions. Included in this evaluation are tanks, heat exchangers, filters, pumps, valves and flanged connections for systems designed for relatively low-pressure, low temperature conditions, but which could possibly be exposed to reactor coolant conditions, either through human error or isolation valve failures. The probabilities of failure, as a function of internal pressure, are evaluated as well as the variabilities associated with them. Leak rates or leak areas are estimated for the controlling modes of failure. Pressure capacities for the pipes and vessels are evaluated using limit-state analyses for the various failure modes considered. The capacities are dependent on several factors, including the material properties, modeling assumptions, and the postulated failure criteria. The failure modes for gasketed-flange connections, valves and pumps do not lend themselves to evaluation by conventional structural mechanics techniques and evaluation must rely primarily on the results from ongoing gasket research test programs and available vendor information and test data.     

Structure and surface properties of diaminocyclohexane plasma polymer films

Plasma polymers of three isomers of diaminocyclohexane (DACH) were deposited on polyethylene, SiO₂, and mica at 20°C. The deposition rate was measured as a function of plasma density and power; a maximum was observed in the latter function. The deposition rate was highest for the monomer with the highest flow rate. The film refractive index was observed to increase with both power density and the degree of fragmentation in the plasma. Film composition was measured by elementary analysis, and was found to be almost identical for each of the three isomers; a mechanism for the polymerization reaction is proposed. The percentage of primary amino groups decreased with increasing power density and with film thickness. Surface force measurements of the thickness and refractive index agreed well with the corresponding ellipsometry values in dry air, and am adhesive force, independent of power density, was measured. When the film was exposed to water vapor, it swelled considerably and the adhesion was determined by capillary forces. Associated with swelling, at high power, was an extremely regular 2-ply rope pattern of protruding material. © 1993 John Wiley & Sons. Inc.     

Synthesis and characterization of poly(ethylene aspartate)-metal complexes

Poly(ethylene aspartate) [PEA] was synthesized by the melt condensation of D,L-aspartic acid and ethylene glycol. PEA containing pendent amino and carbonyl groups in its repeating chain was used as the polymeric ligand for complexation with transition metal ions, viz. Co(II), Ni(II), Cu(II), Mn(II), Zn(II), Cd(II), Ca(II), Mg(II), Pb(II) and Hg(II). Complexation was found to be most effective in DMSO. The resulting polyester-metal complexes were solid coloured materials which have been characterized by IR spectroscopy, elemental analysis and magnetic susceptibility measurements. The thermal stability of the polyester-metal complexes was investigated by thermogravimetric analysis (TGA). On the basis of the physico-chemical studies, an oxygen and nitrogen coordinated structure for the polyester-metal complexes is proposed.     

Packed hyper-ellipsoid classifiers

Pattern classification is frequently performed using the k-nn algorithm or a neural network. The choice of parameters for the former is often difficult and the amount of data which has to be stored in the classifier can be high. Neural network classifiers can overcome some of these problems but learning is often unreliable and slow. An alternative which combines some of the best features of the k-nn and neural network classifier is described by the authors. The classifier is called a packed hyper-ellipsoid classifier     

Void fraction and pressure drop in two-phase liquid metal flows in channels

Experimental results on void fraction and friction pressure drop in vapour-potassium flows in the high-vapour-quality region up to unity are presentéd. The experimental data obtained and the pertinent results of other authors are generalized, and empirical relationship are suggested to calculate void fraction and pressure drop in two-phase liquid metal flows for channels of various configurations and orientations. The relationships are valid within the range of vapour qualities from almost zero to unit. The experimental data prove the mass velocity to have no influence on the hydrodynamic characteristics within the range of the parameters investigated. It is found in the experiments with heat supply that friction pressure losses are smaller than those for adiabatic conditions. It is shown that this result is in good correspondence with the model of the effect of injection in a boundary layer on the value of shear stresses between cases.