A 1.5-V 45-mW direct-conversion WCDMA receiver IC in 0.13-/spl mu/m CMOS

A 2-GHz direct-conversion receiver for wide-band code division multiple access (WCDMA) is presented. It includes two low-noise amplifiers (LNAs), an I/Q demodulator, and two sixth-order baseband channel select filters with programmable gain. Quadrature local oscillator (LO) signals are generated on chip in a frequency divider flip-flop. An external interstage filter between the LNAs rejects transmitter leakage to relax demodulator linearity requirements. A low-voltage demodulator topology improves linearity as well as demodulator output pole accuracy. The active-RC baseband filter uses a programmable servo loop for offset compensation and provides an adjacent channel rejection of 39 dB. Programmable gain over 71-dB range in 1-dB steps is merged with the filter to maximize dynamic range. An automatic on-chip frequency calibration scheme provides better than 1.5% corner frequency accuracy. The receiver is integrated in a 0.13-/spl mu/m CMOS process with metal-insulator-metal (MIM) capacitors. Measured receiver performance includes a 6.5-dB noise figure, IIP2 of +27 dBm, and IIP3 of -8.6 dBm. Power consumption is 45 mW.     

Randomized scheduling algorithms for high-aggregate bandwidth switches

The aggregate bandwidth of a switch is its port count multiplied by its operating line rate. We consider switches with high-aggregate bandwidths; for example, a 30-port switch operating at 40 Gb/s or a 1000-port switch operating at 1 Gb/s. Designing high-performance schedulers for such switches with input queues is a challenging problem for the following reasons: (1) high performance requires finding good matchings; (2) good matchings take time to find; and (3) in high-aggregate bandwidth switches there is either too little time (due to high line rates) or there is too much work to do (due to a high port count). We exploit the following features of the switching problem to devise simple-to-implement, high-performance schedulers for high-aggregate bandwidth switches: (1) the state of the switch (carried in the lengths of its queues) changes slowly with time, implying that heavy matchings will likely stay heavy over a period of time and (2) observing arriving packets will convey useful information about the state of the switch. The above features are exploited using hardware parallelism and randomization to yield three scheduling algorithms - APSARA, LAURA, and SERENA. These algorithms are shown to achieve 100% throughput and simulations show that their delay performance is quite close to that of the maximum weight matching, even when the traffic is correlated. We also consider the stability property of these algorithms under generic admissible traffic using the fluid-model technique. The main contribution of this paper is a suite of simple to implement, high-performance scheduling algorithms for input-queued switches. We exploit a novel operation, called MERGE, which combines the edges of two matchings to produce a heavier match, and study of the properties of this operation via simulations and theory. The stability proof of the randomized algorithms we present involves a derandomization procedure and uses methods which may have wider applicability.     

Oxidative degradation of polyamide reverse osmosis membranes: Studies of molecular model compounds and selected membranes

Selected aromatic amides were used to model the chemical reactivity of aromatic polyamides found in thin‐film composite reverse osmosis (RO) membranes. Chlorination and possible amide bond cleavage of aromatic amides upon exposure to aqueous chlorine, which can lead to membrane failure, were investigated. Correlations are made of the available chlorine concentration, pH, and exposure time with chemical changes in the model compounds. From the observed reactivity trends, insights are obtained into the mechanism of RO membrane performance loss upon chlorine exposure. Two chemical pathways for degradation are shown, one at constant pH and another that is pH‐history dependent. An alternative strategy is presented for the design of chlorine‐resistant RO membranes, and an initial performance study of RO membranes incorporating this strategy is reported. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1173–1184, 2003     

AIRS/Vis near IR instrument

A component of the Atmospheric Infrared Sounder (AIRS) instrument system is the AIRS/Visible Near InfraRed (Vis/NIR) instrument. With a nadir ground resolution of 2.28 km and four channels, the Vis/NIR instrument provides diagnostic support to the infrared retrievals from the AIRS instrument and several research products, including surface solar flux studies. The AIRS Vis/NIR is composed of three narrowband (channel 1: 0.40-0.44 /spl mu/m; channel 2: 0.58-0.68 /spl mu/m, and channel 3: 0.71-0.92 /spl mu/m) and one broadband (channel 4: 0.49-0.94 /spl mu/m) channel, each a linear detector array of nine pixels. It is calibrated onboard with three tungsten lamps. Vicarious calibrations using ground targets of known reflectance and a cross-calibration with the Moderate Resolution Imaging Spectroradiometer (MODIS) augment the onboard calibration. One of AIRS Vis/NIR's principal supporting functions is the detection of low clouds to flag these conditions for atmospheric temperature retrievals. Once clouds are detected, a cloud height index is obtained based on the ratio (channel 2 - channel 3)/channel 1 that is sensitive to the partitioning of water vapor absorption above and below clouds. The determination of the surface solar radiation flux is principally based on channel 4 broadband measurements and the well-established relationship between top-of-the atmosphere (broadband) radiance and the surface irradiance.     

Effect of film thickness on hydrogen content in a-Si : H

The hydrogen content, its depth distribution, and its bonding configuration have been studied in hydrogenated amorphous silicon prepared by plasma-enhanced chemical vapor deposition with hydrogen-diluted silane. Nuclear reaction analysis and infrared spectroscopy were used to determine the total amount of hydrogen and its bonded component, respectively. It has been established that the total concentration of hydrogen does not depend on the film thickness, and has a uniform depth profile. The concentration of bonded hydrogen changes with the film thickness within the measurement accuracy. The data obtained suggest the presence of molecular (non-bonded) hydrogen, uniformly distributed in concentration across the film thickness.     

Lateral ion implant straggle and mask proximity effect

Lateral scattering of retrograde well implants is shown to have an effect on the threshold voltage of nearby devices. The threshold voltage of both NMOSFETs and PMOSFETs increases in magnitude for conventional retrograde wells, but for triple-well isolated NMOSFETs the threshold voltage decreases for narrow devices near the edge of the well. Electrical data, SIMS, and SUPREM4 simulations are shown that elucidate the phenomenon.     

Correction to "Comments on 'On the connectivity in finite ad hoc networks'"

The probability of connectivity of a one-dimensional finite ad hoc network was derived by Desai and Manjunath, and further analyzed by Gore. In this letter, we point out a discrepancy, thus corroborating the original result. However, it provides the exact interpretation of the recursion and derives the probability of connectivity of a one-dimensional finite sensor network.     

Operating Penalties in Single-Fiber Operation 10-Gb/s, 1024-Way Split, 110-km Long-Reach Optical Access Networks

We report for the first time optical signal-to-noise penalties which lead to performance degradations in single-fiber long-reach optical access networks when compared to identical dual-fiber systems. A simplified architecture, with reduced optical amplifier count compared to previous work, for single-fiber operation of a symmetrical 10-Gb/s, 1024-way split, 110-km long-reach optical access network is presented and demonstrated. In addition, a possible solution to remove the optical signal-to-noise penalty is suggested     

A possibilistic clustering approach to novel fault detection and isolation

In this paper, a new approach for fault detection and isolation that is based on the possibilistic clustering algorithm is proposed. Fault detection and isolation (FDI) is shown here to be a pattern classification problem, which can be solved using clustering and classification techniques. A possibilistic clustering based approach is proposed here to address some of the shortcomings of the fuzzy c-means (FCM) algorithm. The probabilistic constraint imposed on the membership value in the FCM algorithm is relaxed in the possibilistic clustering algorithm. Because of this relaxation, the possibilistic approach is shown in this paper to give more consistent results in the context of the FDI tasks. The possibilistic clustering approach has also been used to detect novel fault scenarios, for which the data was not available while training. Fault signatures that change as a function of the fault intensities are represented as fault lines, which have been shown to be useful to classify faults that can manifest with different intensities. The proposed approach has been validated here through simulations involving a benchmark quadruple tank process and also through experimental case studies on the same setup. For large scale systems, it is proposed to use the possibilistic clustering based approach in the lower dimensional approximations generated by algorithms such as PCA. Towards this end, finally, we also demonstrate the key merits of the algorithm for plant wide monitoring study using a simulation of the benchmark Tennessee Eastman problem.