Equivalent linear limit states

The replacement of any limit state function by an equivalent linear function is discussed in detail and it is shown that there are several methods by which such an equivalence may be established. In the case of multiple failure mode problems the definition of fully equivalent linear functions requires the additional consideration of mode correlations. The manner in which this may be carried out is discussed and it is shown that, for most practical cases, a relatively simple analysis is likely to be sufficient to define the set of equivalent linear limit states, with the advantage that the established theory of such linear limit states may then be employed in the majority of reliability analyses.     

Removal of Lissamine Red From Wastewater Using Waste Materials

Feasibility of a waste material, flyash, as a material for purification of wastewater containing Lissamine Red has been studied. Effects of time and concentration, temperature and pH on the removal of the dye have been studied. Lower concentrations favour the uptake of dye from water and the maximum removal was observed at a dye concentration of 20 mgL m 1 , 30°C, pH of 7 and adsorbent particle size of 53 µm. Dynamics of the uptake was studied using Lagergren's equation. The mass transfer coefficient was found to be 0.05 cmmin m 1 at a concentration of 20 mgL m 1 , 30°C and 53 µm particle size.     

Water treatment with silicofluorides and lead toxicity

Toxic metals like lead, manganese, copper and cadmium damage neurons and deregulate neurotransmitters like serotonin and dopamine (which are essential to normal impulse control and learning). Earlier studies show that — controlling for socio‐economic and demographic factors — environmental pollution with lead is a highly significant risk factor in predicting higher rates of crime, attention deficit disorder or hyperactivity, and learning disabilities. Exposure and uptake of lead has been associated with industrial pollution, leaded paint and plumbing systems in old housing, lead residues in soil, dietary habits (such as shortages of calcium and iron), and demographic factors (such as poverty, stress, and minority ethnicity). We report here on an additional “risk co‐factor” making lead and other toxic metals in the environment more dangerous to local residents: the use of silicofluorides as agents in water treatment. The two chemicals in question — fluosilicic acid and sodium silicofluoride — are toxins that, despite claims to the contrary, do not dissociate completely and change water chemistry when used under normal water treatment practices. As a result, water treatment with siliconfluorides apparently functions to increase the cellular uptake of lead. Data from lead screening of over 280,000 children in Massachusetts indicates that silicofluoride usage is associated with significant increases in average lead in children's blood as well as percentage of children with blood lead in excess of 10μg/dL. Consistent with the hypothesized role of silicofluorides as enhancing uptake of lead whatever the source of exposure, children are especially at risk for higher blood lead in those communities with more old housing or lead in excess of 15 ppb in first draw water samples where silicofluorides are also in use. Preliminary findings from county‐level data in Georgia confirm that silicofluoride usage is associated with higher levels of lead in children's blood. In both Massachusetts and Georgia, moreover, behaviors associated with lead nurotoxicity are more frequent in communities using silicofluorides than in comparable localities that do not use these chemicals. Because there has been insufficient animal or human testing of silicofluoride treated water, further study of the effect of silicofluorides is needed to clarify the extent to which these chemicals are risk co‐factors for lead uptake and the hazardous effects it produces.     

Retail Change in Southern Sydney: Lifestyle-Linked Restructuring?

Examination of the changing composition of shopping centres in suburban Sydney between 1969 and 1998 suggests that retail restructuring is linked to lifestyle changes. The growth in the number of shops appears to have matched population growth in the 1990s, suggesting that the suburbanisation of retailing has stabilised. At the same time there has been increasing diversification in terms of the retail functions which are available and in terms of the places where these are available. These changes appear linked to a blurring of the distinction between shopping and leisure and to the use of shopping as a way of signifying identity.     

Development of a continuous respirometer

A continuous oxygen uptake meter or continuous respirometer was developed which produced a rapid and reliable response to systemic shocks. The respirometer basically is a 101. Plexiglas laboratory activated sludge unit with a variable volume air tight side car. The feed enters the completely mixed aeration basin and is pumped into the side car. The side car is the site of the oxygen uptake measurements as indicated by a continuously monitoring dissolved oxygen probe. The system was most sensitive to changes in influent concentrations when run at an F/M = 0.1. Response time for a change in DO of 0.1 ppm was less than 4 min. The continuous respirometer was tested employing both synthetic and raw industrial wastes.     

Modification of Polycaproamide Composites Based on 1H,1H,13H-rihydroperfluorotridecan-1-ol and Montmorillonite

Fibre Chemistry - Modification of polycaproamide by 1H,1H,13H-trihydroperfluorotridecan-1-ol immobilized on montmorillonite produced an F-containing polymer composite. The structure of the...     

Improving the Quality of Cellulose for Use in Disposable Sanitary and Hygiene Products

Fibre Chemistry - Under modern conditions the creation of materials for sanitary hygiene and medical products based on cellulose is of paramount importance. Development and improvement in this area...     

Investigation of 12 – 15 Kev Electron Transmission Through Tapered Glass Capillaries

Glass and Ceramics - The results of experimental studies of the transmission of 12 and 15 keV electron beams through tapered glass macro-capillaries are presented. Measurements showed that there is...     

Mechanical and Tribological Properties of Ca/P-Doped Titanium Dioxide Layer Produced by Plasma Electrolytic Oxidation: Effects of Applied Voltage and Heat Treatment

Plasma electrolytic oxidation (PEO) is a technique that produces a hard oxide layer on the titanium surface where its properties can be tailored by changing the process parameters or by a posterior heat treatment (HT). In this work, a TiO₂ layer with different crystallinity was produced by PEO with different applied voltages (250 to 400 V) and post-HT at 600°C. Our aim was to evaluate the influence of the PEO voltage and HT on the mechanical and tribological properties of anodized Ti. There is an increase in pore size, oxide thickness, and Ca/P ratio for the oxide layer with the applied voltage during the PEO process. X-ray diffraction (XRD) results indicated an increase in the crystalline rutile phase in the oxide layer with voltage and HT. Nanoindentation shows an increase in the oxide hardness and elastic modulus with increased voltage and HT, leading to an improvement in the wear resistance.     

Machining of NiTi-shape memory alloys-A review

The emerging trends in the development of advanced smart materials with better unique properties under different environments for a particular application fascinate the researchers and industrialists. Nickel-Titanium based shape memory alloys are exotic materials due to their unique properties such as SME, SE, high damping characteristics, high corrosion and wear resistance and biocompatibility. This article presents an overview of machining processes that can be used to machine the NiTi and its surface induced characteristics such as microhardness, surface roughness, topography, induced layer, residual stress, fatigue and phase transformation. The surface integrity characteristics are discussed for machining of NiTi-SMAs under the category of traditional, non-traditional and micro-machining with the effect of input parameters such as cutting speed, feed, depth of cut, type of lubricant and type of coating material on cutting tool. The conventional machining of NiTi alloys are quite complicated due to high toughness, severe strain hardening, fatigue hardening and distinctive property of NiTi-SMAs such as pseudoelastic and shape memory effect. From this study, non-traditional process is significantly used to machine the NiTi-SMAs due to its better results on surface integrity characteristics. Consequently, future trends are also identified for machining the NiTi-SMAs and to improve the surface integrity characteristics.