New wire interface for graded 3-D TLM

A new 3-D graded TLM model for thin radiating wires is presented. The model differs from previous TLM models because the wire is modelled at the interfaces between cells, rather than through the centre of the node. The connection between the TLM symmetrical condensed-node link lines and the line forms a 'wire interface'. The scattering algorithm for the interface and simulation results are given.<>     

Über die Eignung der Wechselbiegemaschine „WEBI”︁ zur Ermittlung von Ermüdungskennwerten

On Alternating Bending Machine WEBI's Suitability for Determination of Fatigue Characteristics Already in 1966, experimental investigations revealed that the flat bending torsion testing machine ?FLATO”? (Schenck, Darmstadt) doesn't keep constant its torsional moment amplitude in case of specimen's fatigue softening or hardening, respectively. Thus. conclusions concerning the material's fatigue characteristics drawn from such experimental results might therefore be seriously false. Furthermore, also the alternating bending testing machine ?WEBI”? (Schenck, Darmstadt) shows an equivalent behaviour concerning its bending moment amplitude. For this reason. the main findings of a comprehensive experimental study carried out on WEBI with an unalloyed steel C 45 (0.45 mass perccnl C) in different heat treatment conditions are reported in this paper.     

A novel technique for fabrication of metallic structures on polyimide by selective electroless copper plating using ion implantation

The successful use of palladium ion implantation into polyimide to seed an electroless plated film of copper on the polyimide surface is reported. Polyimide (Hitachi PIX 3400) was implanted with palladium ions to doses of 1.5 × 10¹⁵ − 1.2 × 10¹⁷ ions cm⁻² using a MEVVA ion implanter. The implanted ions acted as sites for nucleation of copper film. A copper film was then deposited on implanted polyimide using a commercial electroless plating solution. The ion energy was kept low enough to facilitate a low critical ‘seed’ threshold dose that was measured to be 3.6× 10¹⁶ Pd ions cm⁻². Test patterns were made using polyimide to study the adaptability of this technique to form thick structures. Plated films were studied with optical microscopy, Rutherford Backscattering Spectrometry (RBS) and Profilometry. The adhesion of films was qualitatively assessed by a ‘scotch tape test’. The film growth (thickness) was observed to be linear with plating time. A higher implantation dose led to greater plating rates. The adhesion was found to improve with increasing dose.     

Manufacture of a high-quality alkylsalicylate additive at the Novokuibyshevsk Petroleum Refinery

Translated from Khimiya i Tekhnologiya Topliv i Masel, No. 4, pp. 16–17, April, 1992.     

Multigigabit/s demultiplexing in optical domain using coherence properties of pulse trains from multiple, asynchronous mode-locked lasers

It is shown that the unique coherence properties of mode-locked lasers can be exploited to provide new opportunities for high-speed data transmission. Using passive Mach-Zehnder optical delay stages, very high bit rate optical data streams constructed from asynchronously combined transmitters can be demultiplexed directly in the optical domain, without imposing restrictions on the source wavelength. Potential implementation and performance of the technique are discussed.<>     

Crystallinity and lateral crystallite size of different UHMW PE materials

Nascent high-molecular-weight (UHMW) polyethylene (PE) samples of different origins show a rather high crystallinity of about 70–75% and contain both a major portion of orthorhombic extended chain crystallites and a minor portion of triclinic crystallites. The triclinic content is greater the higher the molecular weight of the sample and the higher the activity of the used catalyser. A melting / recooling treatment results in a reduction of crystallinity by about 15–25% and disappearance of the triclinic phase. Further, an irreversible conversion of nascent orthorhombic extended chain crystallites to orthorhombic folded chain crystallites of increased lateral dimensions and crystalline perfections takes place during the melting / recooling treatment. The results are compared to those obtained for lower-molecular-weight PE samples and for high-strength / modulus PE fibers of different origins.     

A machine vision system for high speed object tracking using a moments algorithm

A system has been developed for tracking the motion of objects in two dimensions in real-time. The system consists of a conventional CCD camera linked to a transputer-based frame grabber and an array of nine transputers. A parallel moments algorithm is used to extract the co-ordinates of the object's centre of gravity and orientation at field rate, i.e. 60 Hz. Since the position data are made available in real-time—with a small time delay—the system has the potential for inclusion in a feedback loop. Results are presented for tracking the trajectory of a chocolate bar diverted by an air jet. The potential of the system for higher sampling rates—up to 200 Hz—is discussed.     

Current distribution, resistance, and inductance forsuperconducting strip transmission lines

A method for the calculation of the current distribution, resistance, and inductance matrices for a system of coupled superconducting transmission lines having finite rectangular cross-section is presented. These calculations allow accurate characterization of both high-T_c and low-T _c superconducting strip transmission lines. For a single stripline geometry with finite ground planes, the current distribution, resistance, inductance, and kinetic inductance are calculated as functions of the penetration depth for various film thicknesses. These calculations are then used to determine the penetration depth for Nb, NbN, and YBa₂Cu₃O_7-x superconducting thin films from the measured temperature dependence of the resonant frequency of a stripline resonator. The calculations are also used to convert measured temperature dependence of the quality factor to the intrinsic surface resistance as a function of temperature for an Nb stripline resonator