Thermal and mechanical analysis of the ITER plasma-position reflectometry antennas

The antennas of the ITER plasma-position reflectometer are the components most exposed to the plasma. High thermal loads can cause high temperatures and excessive stress, so the first constrains on the antenna design arise from thermal simulations results. Therefore, the first step of the analysis is to develop a finite element thermal model with ANSYS. Once the temperatures are kept at acceptable levels, structural analysis is performed to know the thermal stress. Simulations performed using different materials and support structure geometries are discussed. Further, it has been checked that the components can withstand the electromagnetic loads expected during disruptions and vertical displacement events. The stress due to these electromagnetic loads is calculated analytically as well as with ANSYS simulations. The proposed antenna arrangement is properly designed against thermal and mechanical loads.     

A general theory of force balancing using counterweights

Three equations are derived in this paper from which the force balance conditions of multi-degree of freedom multi-bar planar linkages may be obtained. The linkages can contain both revolute and prismatic joints, though, as discussed in this paper, there force-balance restrictions associated with prismatic joints.     

Effects of boundary conditions on testing of pipes and finite element modelling

The design of many submarine pipelines, especially for operating in deep water, relies on accurate test results for the local buckling collapse of pipes subjected to bending loading. Recent test results have shown apparently anomalous values of axial tensile and compressive strains in comparison to the values that would be expected on the basis of simple bending theory. This could have important consequences for the efficacy of the design factors derived using these anomalous results. Examples of anomalous test results are given in the paper and the cause of the differences between the strain values obtained in the tests and those expected on the basis of simple bending theory are explained using finite element modelling.The major point is that the general application of the simplified engineering theory of bending can be erroneous when ovalisation is imposed or, on the contrary, the boundary conditions of the section are restrained from ovalising deformations.This is a crucial limit state for the design of onshore and offshore pipelines.     

A pilot study of the efficacy of residuum lodges for managing sediment delivery to impoundment reservoirs

Residuum lodges comprise small dams constructed on feeder streams immediately before they enter a reservoir, behind which ponds form, where sediment is deposited. Despite their construction on many impoundment reservoirs (IRE) and catchwaters, little research has previously investigated their efficacy at removing sediments from feeder streams. The current pilot study has, therefore, been carried out at an IRE supplying Halifax, West Yorkshire, UK, where a residuum lodge was recently cleaned out. Sediment concentrations reaching the reservoir were reduced by up to 42% although no certain impacts were noted on the other water quality variables that were measured. Moreover, it was found that the clearance operation did not result in the release of excessive quantities of sediment into the reservoir. It was estimated that the cleared residuum lodge would take 12 years to refill. A survey of other residuum lodges in the Yorkshire region showed there to be considerable differences in their remaining capacities.     

Meta-bromobiphenol epoxy resins: Applications in electronic packaging and printed circuit board

Novel 2,2′,6,6′-tetrabromo-3,3′,5,5′-tetramethyl-4,4′-biphenol (TBTMBP), and its epoxy derivatives, were synthesized to incorporate the stable meta-brominated phenol moiety into epoxy resin systems. In electronic encapsulation and laminate applications, epoxy systems derived from TBTMBP have exhibited superior hydrolytic and thermal stability as compared with the conventional ortho-brominated epoxy resins. These properties have resulted in an extended device life for semiconductors and a high T_g with excellent blister resistance for the printed circuit board, while meeting flame retardancy requirements as well.     

Surface modification of polyethylene by photochemical grafting with 2-hydroxyethylmethacrylate

The photochemical grafting of 2-hydroxyethylmethacrylate onto low-density polyethylene film is described. The grafting technique employed involved irradiating a solution of 2-hydroxyethylmethacrylate and benzophenone in acetone spread between films of poly(ethylene terephthalate) or glass and low-density polyethylene. After irradiation for 2 min, the contact angle of the polyethylene films with water fell from 97° to about 50°. The contact angle of the poly(ethylene terephthalate) substrate also fell during grafting. X-ray photoelectron spectroscopy was consistent with the presence of poly(2-hydroxethylmethacrylate) at the surface of the polyethylene. The effect of solvent on the photochemical grafting of 2-hydroxyethylmethacrylate onto low-density polyethylene is discussed. © 1993 John Wiley & Sons, Inc.     

Differential scanning calorimetry studies on coal. 1. Pyrolysis in an inert atmosphere

Results of thermal changes involved during the pyrolysis of twelve US coals of various ranks in a helium atmosphere at 5.6 MPa (gauge) and temperatures up to 580 °C are reported. Thermal effects during pyrolysis of coals ranging in rank from anthracite to HVC bituminous are endothermic in nature over the temperature range investigated. Exothermic heats are observed only in the case of sub-bituminous and lignitic coals. The net thermal effects, that is the resultant of endothermic and exothermic heats, go from endothermic to exothermic with increase in carbon content, a transition occurring around 66% carbon and another in the reverse direction at about 75% carbon. A maximum in exothermicity occurs around 71% carbon and in endothermicity at about 81% carbon. Results have been compared with published DTA data on coals. The fallacy in the interpretation of published DTA thermograms of coals, where weight changes accompany thermal effects, is discussed.     

Economics of liquid hydrogen from water electrolysis

Using the data from vendors and open literature, we have constructed a preliminary cost model to predict the cost of liquid hydrogen (LH₂) from water electrolysis. The model has been applied to two LH₂ plants. Both have a production rate of 10 886 kg day⁻¹. The first plant (Plant 1) consists of a tank-type electrolyzer and a liquefier and runs all day at the base-load (or equivalent base-load) power rate. The second (Plant 2) consists of a tank-type electrolyzer, a liquefier, a compressor, and storage vessels. The electrolyzer and the compressor shall run only during the off-peak hours at the off-peak power rate. However, the liquefier shall run all day at the base-load (or equivalent base-load) power rate. The costs of LH₂ from both plants are presented. Unless the base-load power rate is high and the off-peak power rate is substantially low, Plant 1 appears to be economically more feasible than Plant 2.     

Preliminary studies of the relation between the carbon texture and the strength of metallurgical coke

Preliminary attempts to relate the carbon texture to the tensile strength of metallurgical cokes are described. Two series of cokes made by carbonizing blended coal charges in pilot scale ovens were examined. The diametral compression test was used to determine the tensile strength of the cokes and the composition of the coke carbon was measured by applying a point-counting technique to the examination of atomic-oxygen etched surfaces. The strengths and textural compositions could be related by a single equation derived by multi-linear regression analysis.     

Some aspects of the role of coal thermoplasticity and coke structure in coal gasification. 2. The effects of pressure and heating rate on dilatometric parameters and optical anisotropy development

An examination of the influence of pressure and heating rate on the thermoplastic properties of a weakly coking coal and of coal with various pitch-like additives was carried out using a high pressure dilatometer. Pressure up to 4 MPa markedly increased the swelling properties and increased the plastic range by decreasing the softening temperature, but the effects of pressure were strongly influenced by rate of heating with high heating rates enhancing the effects. Additions of tar or pitch also enhanced swelling at low pressure. The solid carbonization residues from the dilatometer were examined by polarized light microscopy to determine the content and composition of optically anisotropic species. The anisotropic content was increased by increases in pressure and heating rate and pitch additives enhanced the anisotropic content, especially at low pressure, without affecting the composition of the anisotropy. No direct correlations exist between the dilatometric parameters and the optical anisotropy but their dependence on the conditions emphasizes that when considering high pressure gasification of coal, it is necessary to obtain data under appropriate conditions.