Effect of Wall Surface Properties at Different Drying Kinetics on the Deposition Problem in Spray Drying

Current methods in alleviating the wall deposition problem in spray drying emphasize mainly controlling the stickiness of the drying particles and less attention is placed on the properties of the dryer wall. In this experimental study, the effect of wall surface properties on the deposition mechanism has been investigated. Properties considered in classifying different wall materials were surface energy, roughness, and dielectric properties. The model solution contained sucrose, representing low-molecular-weight sugars commonly encountered in spray drying of fruit and vegetable juices. The effect of wall properties on deposition was explored at different drying rates producing particles of different surface rigidity. Larger surface roughness produced higher deposition fluxes for particles with high impact velocity and moisture. Surface energy and surface roughness were found to have no significant effect for dry rigid particles at the middle and bottom elevation of the drying chamber. However, material with lower surface energy (Teflon) exhibited less deposition for rubbery particles at such elevations. Analysis shows that dielectric wall material (Teflon) tends to enhance deposition of dry particles because of attrition at the surface. Higher wall temperature was found to produce slightly more deposition. The results of this work give a general indication of the effect of wall material on the deposition problem and provide the fundamental understanding for further studies along this line. Proper selection of dryer wall material will provide potential alternatives for reducing the deposition problem.     

Enhanced direct stiffness method for finite element analysis of textile composites

Traditional homogenization techniques are not useful when the microstructural scale of a material is of the same order of magnitude as the structural scale of a component. Such is the case for many textile composites. Since discrete modeling of the microstructure throughout a component is prohibitively expensive, continuum finite elements are needed which account for the microstructure within a single element. This paper describes a simple substructuring technique for formulating these special elements.     

Serum amyloid P component scintigraphy and turnover studies for diagnosis and quantitative monitoring of AA amyloidosis in juvenile rheumatoid arthritis

OBJECTIVE: To evaluate aspects of the natural history of AA amyloidosis complicating juvenile rheumatoid arthritis (JRA), and its response to therapy with chlorambucil. METHODS: Scintigraphy and 7-day turnover studies were performed in JRA patients with histologically proven (n = 35) or clinically suspected (n = 30) AA amyloidosis, following intravenous injection of 123I and 125I-labeled serum amyloid P component (SAP). Prospective monitoring studies were performed over 2-3 years in 20 patients with amyloidosis. All but 2 amyloidosis patients were treated with chlorambucil. RESULTS: Positive scanning results were obtained in all patients in whom imaging was performed within 12 years of positive biopsy findings of amyloid and in 5 patients with clinically suspected amyloidosis. Negative scanning results with normal SAP metabolism, indicating regression of amyloid, were obtained in 4 patients whose amyloidosis had been in full clinical remission for more than 12 years. Prospective monitoring studies in patients whose JRA-associated inflammatory activity was in remission demonstrated regression of amyloid in 8 patients and no substantial changes in 8 others; however, in 4 further patients with active inflammation, there was accumulation of amyloid. There was a very poor correlation between the amount of amyloid present at a particular site and the resultant organ dysfunction. CONCLUSION: Radiolabeled SAP scintigraphy and turnover studies are useful complementary tools in the diagnosis, screening, and quantitative monitoring of type AA amyloidosis in JRA. The amyloid deposits may progress and/or regress at different rates in different anatomic sites over short periods.     

Decreasing miscibility with greater heterogeneity in ternary polymer blend: poly(cyclohexyl methacrylate), poly(α‐methyl styrene) and poly(4‐methyl styrene)

A ternary blend system comprising poly(cyclohexyl methacrylate) (PCHMA), poly(α‐methyl styrene) (PαMS) and poly(4‐methyl styrene) (P4MS) was investigated by thermal analysis, optical and scanning electron microscopy. Ternary phase behaviour was compared with the behaviour for the three constituent binary pairs. This study showed that the ternary blends of PCHMA/PαMS/P4MS in most compositions were miscible, with an apparent glass transition temperature (T_g) and distinct cloud‐point transitions, which were located at lower temperatures than their binary counterparts. However, in a closed‐loop range of compositions roughly near the centre of the triangular phase diagram, some ternary blends displayed phase separation with heterogeneity domains of about 1 µm. Therefore, it is properly concluded that ternary PCHMA/PαMS/P4M is partially miscible with a small closed‐loop immisciblity range, even though all the constituent binary pairs are fully miscible. Thermodynamic backgrounds leading to decreased miscibility and greater heterogeneity in a ternary polymer system in comparison with the binary counterparts are discussed. © 2003 Society of Chemical Industry     

The oxidative inducation test applied to medical PVC and other polymers

We have examined the applicability of this simple and effective test to polymer systems widely used in the medical industry. First, it was found that not every polymer examined exhibited a distinct onset of autocatalytic oxidation detectable by DSC. However, for cases where distinct onsets are found, powerful insights can be obtained. These included activation energy of the degradation, thermal oxidative shelf life prediction, and correlation, with product performances. Actual examples are presented to illustrate the utility of the test.     

Decision-directed maximum-likelihood estimation of OFDM framesynchronisation offset

The authors propose a method to estimate the synchronisation offset for orthogonal frequency division multiplexing (OFDM) frame alignment without resort to pilot tones. A decision-directed maximum-likelihood estimation of frame synchronisation offset is derived, and the performance of the proposed scheme is confirmed by computer simulation for QAM systems     

Modeling the I-V characteristics of fully depleted submicrometerSOI MOSFET's

In this paper, an analytic current-voltage model for submicrometer fully-depleted (FD) silicon-on-insulator (SOI) MOSFET's is presented. This model takes into account the source/drain series resistances which can be especially high in thin film SOI devices. The effect of drain induced conductivity enhancement is also included, which is important for submicrometer channels. The model is verified by comparison to measured SOI I-V characteristics. Good agreement is obtained for SOI film thicknesses ranging from 40 to 220 nm and effective channel lengths down to 0.25 μm     

A quadruple well, quadruple polysilicon BiCMOS process for fast 16Mb SRAM's

An advanced, high-performance, quadruple well, quadruple polysilicon BiCMOS technology has been developed for fast 16 Mb SRAM's. A split word-line bitcell architecture, using four levels of polysilicon and two self-aligned contacts, achieves a cell area of 8.61 μm² with conventional I-line lithography and 7.32 μm² with I-line plus phase-shift or with deep UV lithography. The process features PELOX isolation to provide a 1.0 μm active pitch, MOSFET transistors designed for a 0.80 μm gate poly pitch, a double polysilicon bipolar transistor with aggressively scaled parasitics, and a thin-film polysilicon transistor to enhance bitcell stability. A quadruple-well structure improves soft error rate (SER) and allows simultaneous optimization of MOSFET and bipolar performance     

Effects of α‐form or β‐form nuclei on polymorphic crystalline morphology of poly(butylene adipate)

The effects of α‐form and β‐form nuclei on polymorphic morphology of poly(butylene adipate) (PBA) upon recrystallization from the molten state up to various T_max values were examined by differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD) and polarized light microscopy (PLM). In this study, PBA with complex melting and polymorphism behaviour was used as a model for examining different types and extents of residual nuclei. As the PBA initially containing the sole α‐crystal was brought to a molten state of various T_max, the extents of trace α‐form crystal nuclei varied and were dependent on T_max. Furthermore, it did not matter whether, initially, the PBA contained α‐ or β‐form crystals (or both) because only a single type of α‐nuclei could be left upon treatment to the molten liquid state at T_max. Therefore, only the α‐crystal in PBA had ‘memory capacity’ in the molten liquid state while the β‐crystal did not. This was so because the latter had been completely transformed into the solid state prior to being heated into a liquid. PBA crystallized before α‐nuclei could be packed into α‐crystal, regardless of the crystallization temperature (T_c). For recrystallization from molten PBA without any nuclei, the crystalline polymorphism was correspondingly influenced by T_c. Copyright © 2005 Society of Chemical Industry     

New approach to enhance adhesions between carbon nanotube emitters and substrate by the combination of electrophoresis and successive electroplating

Complementary electroplating combined with electrophoresis enhanced the field emission characteristics of emitters by improving the adhesions between CNT emitters and substrate. The emitting current of the CNT emitters prepared by our combined method increased nine times higher than that of CNT emitters prepared by electrophoresis only, since electroplating improved the adhesion of CNT emitters. During the life-time measurement for 10 h, the emitting current of CNT emitters fabricated by electrophoresis only was drastically decreased to 13% of the initial current, while that prepared by the combination of electrophoresis and successive electroplating decreased to 64% of the initial current. We suggest that our method is a promising approach for the efficient fabrication of reliable CNT emitters.