A facile antistatic modification of polyester fiber based on ion-exchange reaction of sulfonate-modified polyester and various cationic surfactants

A new technique for imparting antistatic properties to poly(ethylene terephthalate) (PET) fiber has been developed. In this technique, blend polyester fibers containing poly(ethylene terephthalate/5-sulfoisophthalate) (SIP-PET) were prepared by blend spinning and then treated with various cationic surfactants in the process of dyeing. The surfactants could effectively be immobilized on the fiber as the counter cations of the sulfonate groups of the 5-sulfoisophthalate (SIP) units and aid the release of static electrons formed in the fiber. Thus, the half-life time (t_1/2) of leakage of static charge and the surface resistivity (Rs) of the blend PET fibers became much lower after treating. The best result was obtained with a methylated quaternary ammonium salt of a stearylamine-ethylene oxide (EO) adduct or hydrochloride of a laurylamine-EO adduct as the surfactant of which the number of EO units was around ten. Even after five washing cycles the t_1/2 value of the fibers treated with these surfactants was kept lower than 30 s with the Rs value maintained in the order of 10¹³ Ω cm^-2. Therefore, the present technique could be useful for practical production of polyester fibers with “semi-permanent” antistatic properties which can be recovered by re-treatment even if they were lost.     

A survey on video content rating: taxonomy,challenges and open issues

Multimedia Tools and Applications - Rating a video based on its content is one of the most important solutions to classify videos for audience age groups. In this regard, Film content rating and TV...     

Winglet geometry effects on tip leakage loss over the plane tip in a turbine cascade

The effects of winglet offset distance, winglet coverage, and winglet cross section on the over-tip leakage loss for the plane tip have been investigated experimentally in a turbine blade cascade for a tip gap height-to-span ratio of h/s = 1.36 %. The results show that the over-tip leakage loss for the full coverage winglet increases steeply with increasing the winglet offset distance. This loss generation is attributed to flow disturbances over the forward-facing and backward-facing steps within the tip gap. The winglet flush mounted to the tip surface provides the best result. With the leading edge winglet portion or without it, the both-side winglet always provides better aerodynamic performance than the corresponding pressure-side winglet or suction-side winglet. Longer coverage of the both-side winglet leads to lower loss. Therefore, the full coverage winglet performs best in the loss reduction for the plane tip. In general, thinner winglet leads to better aerodynamic result, and the winglet cross section having a slant bottom surface with the smallest thickness at its outer end is recommended.     

Temperature and grain size dependence of superplasticity in a Zn−0.3wt.%Al alloy

The superplastic deformation behavior of quasi-single phase Zn-0.3 wt. %Al was investigated. A series of load relaxation and tensile tests was conducted at various temperatures ranging from RT (20 °C) to 200 °C. The recently proposed internal variable theory of structural superplasticity was applied. The flow curves obtained from load relaxation tests were shown to consist of contributions from interface sliding (IS) and accommodating plastic deformation. In the case of quasi-single phase Zn-0.3 wt.% Al alloy with an average agrain size of 1 μm, the IS behavior could be described as a viscous flow process characterized by a power index of M_g=0.5. A large elongation of about 1400% was obtained at room temperature and the strain rate sensitivity parameter was about 0.4. Although relatively large-grained (10 μm) single phase alloy showed a high value of strain rate sensitivity comparable to that of fine-grained alloy at very low strain rate range, IS was not expected from the analysis based on the internal variable theory of structural superplasticity at room temperature. As the temperature increased above 100 °C, however, the contribution from IS was observed at a very low strain rate range. A high elongation of ∼400% was obtained in a specimen of 10-μm-grain-size at 200 °C under a strain rate of 2×10⁻⁴/sec. Jointly appointed at Center for Advanced Aerospace Materials (CAAM)     

Effect of yttrium on the stability of aluminide-yttrium composite coatings in a cyclic high-temperature hot-corrosion environment

A composite coating of aluminide-yttrium has shown excellent corrosion resistance in a cyclic high-temperature hot-corrosion environment. To understand the effect of yttrium on the stability of the composite coating, the specimens were prepared with various coating parameters of Y thickness, sequence of post heat treatment and surface condition before Y-ion plating. Performance of the composite coating was evaluated by isothermal oxidation and cyclic high-temperature hot corrosion. Isothermal-oxidation-test results show that the Y in the composite coating helps to form a thick and dense Al₂O₃ scale which is ductile and resistant to thermal stress. The Y in Al₂O₃ may act as a donor which leads to an increase in concentration of interstitial oxygen and, thus, increases in oxidation rate. The presence of Y₂O₃ and (Y, Al) O-type compounds in grain boundaries of Al₂O₃ and boundaries between the Al₂O₃ and NiAl effectively prohibits the fast diffusion of oxidants (such as O and S) and Al along grain boundaries. Consequently, it may induce slow diffusion through the matrix, and thus the corrosion resistance of the composite coating under cyclic hot corrosion increases substantially.     

Effect of rinsing and drying on silicon surface cleaning for epitaxial growth

We investigated the effect of the rinsing and drying technique on the oxygen and carbon concentration on a silicon surface. Rinsing in deionized water increased the interfacial oxygen concentration and helped generate defects. Blow-drying was more efficient than spin-drying in reducing interfacial oxygen concentration. Exposure to the atmosphere was detrimental to obtaining high crystallinity in the epitaxial layer. We evaluated the effectiveness of the cleaning process by observing the grown epilayer and the epilayer/substrate interface.     

Process for dense 2D SiC fiber-SiC matrix composites

A new process using SiC fiber fabrics and SiC tapes to produce dense 2D SiC fiber-SiC (SiC/SiC) composites is demonstrated. The strategy for fabricating the SiC/SiC composites involves: (i) alternately stacking the SiC fiber fabrics and SiC tapes at room temperature, (ii) pyrolyzing of the stacked composites, and (iii) hot-pressing the pyrolyzed composites. By controlling the hot-pressing temperature, it is possible to obtain dense 2D SiC/SiC composites with relative densities of >98%. The 2D SiC/SiC composites show no degradation of the SiC fibers and a higher mechanical strength.     

Effects of anodizing voltage on the anodized and hydrothermally treated titanium surface

Anodic oxidation is the process of creating a titanium oxide layer with various defects more dense and stable. In this study, a dense, stable and porous oxide layer was formed using anodic spark oxidation on pure titanium surface and hydroxyapatite crystals were formed on its surface via a hydrothermal treatment. A mixture of 0.02M−GP (Glycerolphosphate disodium salt) and 0.2M-CA (Calcium acetate) was used as an electrolyte. By increasing the anodizing voltage to 220, 260, 300, and 360 V, the effects of the anodizing voltage were examined by evaluating the film properties after anodization and a hydrothermal treatment. Breakdown occurred around 230 V. As the voltage increased after breakdown, the pore size increased. After the hydrothermal treatment, the amount of HA crystal precipitation was also increased as the voltage increased. The mean surface roughness (Ra) of the anodizing surface was also increased as the voltage increased. The Ra value was larger in the hydrothermally treated group compared with the group treated with anodization as a result of the HA crystals present on the surface after the hydrothermal treatment. Corrosion resistance of the surface modified by anodization was significantly increased in a saline solution compared to that for the non-treated group; this increased further after the hydrothermal treatment. These increases were most likely due to a thick stable oxide layer formed through anodization. Thus, it is believed that titanium with its surface modified through anodic spark oxidation would be a suitable biomaterial due to its corrosion resistance and biocompatibility.     

Galvanic coupling effect on corrosion behavior of Al alloy-matrix composites

Galvanic coupling effect on the corrosion of SiC-reinforced aluminum alloy-matrix composites was investigated in a sodium chloride solution. The potentiodynamic polarization measurement indicated that pitting potentials of metal matrix composites (MMCs) and AA2124 matrix alloy were similar, and pitting potential of MMCs was almost same as corrosion potential, while pitting susceptibility of MMCs was higher than that of AA2124 alloy. Galvanic current by formation of galvanic couple between SiCw and matrix reveals very low value because of large cathodic polarization of SiC. However, by increasing potential of matrix to pitting potential by this galvanic couple and thus, forming pits easily at the weak passive film near SiC reinforcing phase preferentially, it is concluded that pitting susceptibility of MMCs increases highly than AA2124 alloy of matrix composition.     

Effect of silicon content and annealing temperature on formation of retained austenite and mechanical properties in multi-phase steels

Cold-rolled and annealed ultra-high strength sheet steels with good ductility accompanied by TRIP of retained austenite have received considerable attention in recent years. This paper discusses the effect of silicon content and annealing temperature on the formation of retained austenite and the mechanical properties in Fe-0.34%C-1.7% Mn steels whose structure consists of ferrite, bainite and retained austenite. Silicon inhibited the cementite formation in bainite during isothermal holding and partitioned carbon from bainite to austenite, resulting in an increase in retained austenite content. When the silicon content was increased to 1.0 wt.% or higher, the amount of retained austenite markedly increased leading to good mechanical properties. 0.34%C-1.03%Si-1.7%Mn steel showed a high tensile strength of 1,030 MPa and a total elongation of 34.5% when annealed at 780°C for 5 min followed by isothermal holding at 400°C for 5 min. In this case, the amount of retained austenite was about 25%. The variation in tensile strength-elongation combination had good correlation with that in the amount of retained austenite with both annealing temperature and silicon content. The most retained austenite was obtained in the steel annealed at just above A_C1 temperature. The annealing temperature which gives the most retained austenite was decreased with decreasing the silicon content.