Standby power system VRLA battery reserve life estimation scheme

This paper presents a valve-regulated lead acid (VRLA) battery reserve life estimation scheme. The scheme is adaptive in both type and frequency of involvement. The scheme is based on capacity trending with the support of a number of state-of-health (SOH) indicators. These SOH indicators include accumulated thermal stress, float voltage, and indicators acquired from the start-of-discharge (coup de fouet) region. An implementation test case is given, indicating that the scheme is capable of providing an accurate estimation of reserve life long before the end of life. Furthermore, the estimation accuracy improves as the end of battery life approaches.     

An Experimental Investigation into the Feed Rate Capacity of Rotary Valve and Blow Tank Feeders

Industry widely uses rotary valves and blow tanks for the pneumatic conveying of products, each having their pros and cons depending on the specific application. This article shows the differing results obtained when low-velocity conveying a product through a common pipeline using both a drop-through rotary valve and a bottom-discharge blow tank feeder. A number of issues arise in the rotary valve system, the main one being rotary valve air leakage. A blow tank system, on the other hand, does not leak, as it is an enclosed system. The experimental results show dramatic differences in product throughput. Further exploration leads to a novel modification being made to the rotary valve system in an attempt to increase its capacity. The result of this modification shows a slight increase in output tonnage, but still significantly less than that obtained from the blow tank.     

Organic matter release in low temperature thermal treatment of biological sludge for reduction of excess sludge production.

Thermal treatment applied in association with a biological system allows for a significant reduction in excess sludge production (approximately 50%). In general, heat treatment is described as a sludge disintegration technique. This paper offers a thorough study on the impact of heat treatment, at temperatures below 100 degrees C, on the solubilisation of the sludge COD and its biodegradability. Discontinuous heating experiments were performed on activated and digested sludge. At all temperatures tested the released COD for digested sludge was systematically higher than that for activated sludge (15 and 40%, respectively, at 95 degrees C for 40 min of contact time). For the first 30 min, a 1st order kinetic, with respect to the residual COD, was systematically found. In the range of 40-95 degrees C, digested sludge had a lower activation energy than activated sludge (26 kcal/mol compared to 70-160 kcal/mol). COD solubilisation is thus more positively influenced by temperature in the case of activated sludge. This may be due to the significant difference in the ratio of protein/carbohydrate in digested and activated sludge (1-5 and 0.2-0.7, respectively). The increase in the COD/TKN ratio in the solubilised fraction after thermal treatment of activated sludge suggests a preferential solubilisation of proteins over carbohydrates. Respirometric tests performed on the solubilised COD showed that whatever the sludge origin, only 40-50% of released COD is biodegradable at a conventional hydraulic retention time (i.e., 24 h). Hence, heat treatment would act more through organic matter solubilisation rather than by a biodegradability increase.     

Effect of broaching on high-temperature fatigue behavior in notched specimens of INCONEL 718

Notches were machined in specimens of INCONEL 718 by a broaching process, where differing broaching runs led to differing extents of subsurface deformation and surface roughness. Fatigue tests were carried out at 600 °C with a trapezoidal loading waveform at 0.25 Hz. The broaching process that led to the more severe subsurface deformation (but lower surface roughness) showed the worst fatigue performance. Analysis of total strain amplitude in the notch root with the aid of an elastoplastic finite-element (FE) model showed that the work hardening related to the subsurface deformation caused by the different broaching can account for the difference in fatigue lives. Differences in initiation and growth behavior were seen for the two broached finishes as well as for broached and subsequently polished samples. These differences are discussed in terms of a change in crack growth initiation and growth mechanisms due to the presence of the work-hardened layer.     

Performance of simple response method for the establishment and adjustment of calibration intervals

Managing calibration intervals in order to fulfill requirements of quality-oriented organizations is discussed in this paper. In particular, the simple response method is considered. According to this technique, the interval between successive calibrations is adjusted adaptively on the basis of the outcome of the last calibration process. An original analysis is presented about the properties of such calibration interval handling methods. Finally, directions are given on how to tune its parameters optimally, in order to meet desired levels of long-term measurement reliability.     

Use of electrochemical oxidation process as post-treatment for the effluents of a UASB reactor treating cellulose pulp mill wastewater.

The main purpose of this study was to evaluate the performance of the electrochemical oxidation process as a post-treatment for the effluents of a bench-scale UASB reactor treating simulated wastewater from an unbleached pulp plant. The oxidation process was performed using a single compartment cell with two plates as electrodes. The anode was made of Ti/Ru0.3Ti0.7O2 and the cathode of stainless steel. The following variables were evaluated: current density (75, 150 and 225 mA cm(-2)) and recirculation flow rate in the electrochemical cell (0.22, 0.45 and 0.90 L h(-1)). The increase in current density from 75 to 225 mA cm(-2) did not increased the color removal efficiency for the tested flow rates, 0.22, 0.45 and 0.90 L h(-1), however the energy consumption increased significantly. The results indicated the technical feasibility of the electrochemical treatment as post-treatment for UASB reactors treating wastewaters from pulp and paper plants.     

Static and pulsed pressures measured using electrically conducting rubbers

A method of measuring static and pulsed pressures using electrically conducting rubber sensors is proposed. The method is based on a change in the volume resistivity of a filled rubber under the action of external pressure. The pressure-induced change in resistance of the rubber sensor is proportional to the applied pressure and can be measured by a bridge circuit. Using this method, it is possible to evaluate the degree of homogeneity of the pressure distribution over a solid surface. This is achieved by distributing rubber sensors over the given surface.