Tube-shaping unit — A way of improving the quality of shaped tubes

Lenin Dnepropetrovsk Pipe Plant. Translated from Metallurg, No. 8, p. 39, August, 1989.     

Three ways to implement interfacial techniques: application tomeasurements of chromatic dispersion, birefringence, and nonlinearsusceptibilities

Depending on the spectal width of the source illuminating an interferometer, measurement procedures can utilize either the whole interferogram, or only the fringe envelope, or only the fringe quick oscillations. With an ultraband spectrum source, a simplified adaptation of the methods of Fourier transform spectroscopy yields the variations of the test-fiber propagation constant over the whole wavelength-interval of the source. Chromatic dispersion can then be computed from a single interferogram. With narrower spectrum sources, only the fringe envelopes are utilized and yield measurements of mode delay, with application to chromatic and polarization mode dispersion. In this case, however, interferograms at several wavelengths are necessary. With even narrower spectrum sources, the fringe quick oscillations provide measurements of phase shifts, related to changes in the mode propagation constant, when outside perturbations are applied to the test fiber. A direct method for measuring the third-order nonlinear susceptibilities is discussed. In this case the outside perturbation is an intense pump laser field     

Continuous phase quadrature phase shift keyed signaling techniquewith coding

A continuous phase quadrature phase shift keyed (CPQPSK) modulation technique is presented. This method utilizes a conventional QPSK modulator and a phase trajectory converter to approximate M=4, h=1/4 continuous phase signal and allows low cost, low complexity, and high rate (>1 Gbit/s) CPM modem implementation for bandwidth efficient transmission through nonlinear satellite channels. Using a communications analysis computer program it has been found that CPQPSK has 99 percent out-of-band power of 0.8R (MSK has 99 percent out-of-band power of 1.2 R where R is defined as bit rate), continuous phase trajectories, and nearly constant envelope amplitude. Simulation of realistic hardware designs indicate that the CPQPSK will require an Eb/No of 14 dB to achieve a bit error rate (BER) of 10^-6. Forward error correcting techniques using block codes with an overhead of 10 percent indicate that the Eb/No requirements can be reduced to 11.2 dB for 10^-6 BER     

Half-bridge inverter using 4H-SiC gate turn-off thyristors

This paper reports on the first demonstration of a half-bridge power inverter constructed from silicon carbide gate turn-off thyristors (GTOs) operated in the conventional GTO mode. This circuit was characterized with input bus voltages of up to 600 VDC and 2 A (peak current density of 540 A/cm²) with resistive loads using a pulse-width modulated switching frequency of 2 kHz. We discuss the implications of the thyristor's electrical characteristics and the circuit topology on the overall operation of the half-bridge circuit. This work has determined the conservative critical rate of rise value of the off-state voltage to be 200 V/μs in these devices     

Interactions of electron beams with surfaces of MgO crystals

The strong interaction of electrons with the flat surfaces of small crystals has been investigated by high resolution CTEM and STEM instruments. When cubic crystals of MgO smoke with edges 20–300 nm are oriented so that the ?001? or ?011? zone axis is parallel to the optical axis, then two kinds of external fringes are observed at (100) surfaces. One kind is parallel to the surface, having spacings up to 0.4 nm. These are caused by interference among the electron channelled along the surface. Fresnel-diffracted ones and the remnant of the incident beam. Fringes of the other kind, which appear as fine structure in the first kind of fringes, are perpendicular to the crystal edge. When an electron beam is parallel to the ?011? axis, the second kind of fringe, whose spacing is 0.3 nm corresponding to d₀₁₁, shows the difference of the surface potential between magnesium atoms and oxygen atoms. Selected area diffraction patterns and microdiffraction patterns also show the same periodicities as in the two kinds of fringes. Simulated images, using the scattering amplitudes for ions, are compared with observations.     

Effect of facet coatings on far fields of semiconductor lasers

A theoretical expression is derived for the far fields of semiconductor lasers with coated facets. It is shown that the far fields are different for uncoated, antireflection-coated and high-reflection-coated lasers. The correction factor for the far fields is shown to depend on the transmission coefficient of the facets.     

Implementation of a self-timed segmented bus

We propose an asynchronous structure for implementation on a SoC. An intersegment topological arrangement preserves parallelization and, through a so-called central arbiter, efficiently organizes communication with high signaling speed in the proposed structure. Researchers proposed the concept of segmenting buses primarily for multicomputer architectures. More recent approaches address on-chip implementation of segmented buses. We present an asynchronous segmented-bus architecture targeted for the modular design of high-performance SoC applications. The structure not only enables faster operation than a conventional bus system but also offers lower power consumption per transferred data item. This is possible because segmentation is realized in such a way that the majority of data transfers in the system are intrasegment transactions on relatively short wires with low or moderate capacitive loads.     

A Distributed State Estimator Utilizing Synchronized Phasor Measurements

With the creation of balancing authorities by the North American Reliability Council that span large portions of the North American interconnection, and stringent requirements for real time monitoring of power system evolution, faster and more accurate state estimation algorithms that can efficiently handle systems of very large sizes are needed in the present environment. This paper presents a distributed state estimation algorithm suitable for large-scale power systems. Synchronized phasor measurements are applied to aggregate the voltage phase angles of each decomposed subsystem in the distributed state estimation solution. The aggregated state estimation solution is obtained from the distributed solution using a sensitivity analysis based update at chosen boundary buses. Placement of synchronized phasor measurements in the decomposed subsystems is also investigated in this paper. Test results on the IEEE 118-bus test bed are provided