Occurrence and characterisation of the hydrogen-evolving enzyme in Frankia sp.

An increase in hydrogen evolution from the hydrogen-evolving enzyme in the actinomycete Frankia was recorded in the presence of nickel. Immunogold localisation analysis of the intracellular distribution of hydrogenase proteins indicated that they were evenly distributed in the membranes and cytosol of both hyphae and vesicles. In addition, molecular characterisation of the hydrogen-evolving enzyme at the proteomic level, using two-dimensional gel electrophoresis combined with mass spectrometry, confirmed that the Frankia hydrogen-evolving enzyme is similar to the cyanobacterial bidirectional hydrogenase of Anabena siamensis.     

Visible transmission spectroscopy for the assessment of egg freshness

The objective of this research was to investigate the feasibility of visible transmission spectroscopy for the non‐destructive assessment of the freshness of an individual egg. A total of 600 intact white‐shelled eggs of the same flock (Lohmann, 40 weeks of age) were measured. To obtain a considerable variation in freshness, groups consisting of 60 eggs were stored (18 °C, 55% RH) for 0, 2, 4, 6, 8, 10, 12, 14, 16 and 18 days. The non‐destructive spectral measurements were compared with the two most widely used destructive freshness parameters, namely Haugh units and albumen pH. A partial least squares (PLS1) model was built in order to predict Haugh units and pH of the albumen based on the transmission spectra. The correlation coefficients between the predicted value and the measured value were 0.842 and 0.867 for Haugh unit and pH of the albumen, respectively. These results show that the light transmission spectrum of an egg provides quantitative information about egg freshness. Relevant information concerning egg freshness is restricted to the interval between 570 and 750 nm. Furthermore, the models obtained for both destructive parameters were strikingly similar, indicating that Haugh unit and pH have the same physico‐chemical background. Copyright © 2006 Society of Chemical Industry     

Prediction of brittle-to-ductile transitions in polystyrene

In this study it is attempted to predict brittle-to-ductile transitions (BDTs) in polystyrene blends, induced either by an increase in temperature or by a decrease in inter-particle distance. A representative, two-dimensional volume element (RVE) of a polystyrene matrix with 20% circular voids, is deformed in tension. During deformation a hydrostatic-stress based craze-nucleation criterion [1] is evaluated. The simulations demonstrate that crazes initiate at low temperatures while a transition from crazing to shear yielding (BDT) is found around 75 °C. The numerical results correlate well with tensile tests on similar heterogeneous polystyrene. The presence of an absolute length, as experimentally found, is more difficult to explain. Near a free surface a T_g-depression is measured for polystyrene and also the resistance to indentation in polystyrene is lower than expected from bulk properties. Both observations are rationalised by an enhanced segmental mobility of chains near a free surface. As a consequence of these findings, an absolute length-scale could be incorporated in the numerical simulations. For simplicity, the length-scale is modelled by taking a temperature gradient over a thin layer near the internal free surfaces of the RVE. Deformation of the RVE with different absolute length-scales shows that indeed also the experimentally found brittle-to-ductile transition can be predicted if the ligament thickness between the inclusions (‘voids’) in polystyrene is below a critical value of ca. 15 nm.     

Formulation of a ceramic ink for a wide-array drop-on-demand ink-jet printer

This paper describes the methodology for simulating a reprographic ink with a ceramic ink based on a commercially available zirconia powder for direct ceramic ink-jet printing. Of over-riding importance was matching viscosity and this was tested systematically by using a mineral oil–hexane binary system. Of secondary importance was adjustment of the pressure defect behind the nozzle to compensate for small differences in surface tension. The inks tested in the wide array print-head were based on low electrical conductivity liquids to avoid damage to the electroding system. The organic binder for the zirconia ink was paraffin wax and the dispersant was a hydroxystearic acid based polyester.     

Practical OSPF traffic engineering

Open Shortest Path First (OSPF) traffic engineering (TE) is intended to bring long-awaited traffic management capabilities into IP networks, which still rely on today's prevailing routing protocols: OSPF or IS-IS. In OSPF, traffic is forwarded along, and split equally between, equal cost shortest paths. In this letter, we formulate the basic requirements placed on a practical TE architecture built on top of OSPF and present a theoretical framework meeting these requirements of practicality. The main contribution of our work comes from the recognition that coupled with an instance of the maximum throughput problem there exists a related inverse shortest-path problem yielding optimal OSPF link weights.     

Techniques for high-frequency integrated test and measurement

This paper describes techniques for the on-chip measurement of high-frequency and/or high-bandwidth electrical phenomena in ultra large-scale integration environments. The techniques rely on the integration of multiple compact and robust electronic test devices, or cores, at various locations within an integrated circuit. The cores consist primarily of signal generators that approximate the output of a sigma-delta modulator using finite repetitious bit patterns and a small set of highly robust analog components. They are capable of digitizing on-chip signals at gigahertz rates even using low-cost manufacturing processes. Simple communication between the multiple cores enables the migration of many "board-level" type measurements down to the chip level.