Analytic investigation of effect of electric field on elasto-plastic response of a functionally graded piezoelectric hollow sphere

In this work, the effect of electric potential on the mechanical (Stresses, strains, displacement) and electrical (electrical displacement and intensity) response of a Functionally graded piezoelectric (FGP) hollow sphere is analytically investigated. The sphere is under the action of internal/external pressure and temperature gradient as well. The inhomogeneity is based on power law in radial direction. The analysis is done in two parts: elastic response and plastic response, using Tresca yield criterion. It is shown by illustrative example that under internal pressure and assumed model parameters, the commencement of plastic region is from outside surface towards inside in the plastic zone is extended with the increase of electric potential. Interestingly, radial stress and displacement have an extreme not on the boundaries, but on the inside.     

CFD modeling of a radiant tube heater

This paper reports experimental and Computational Fluid Dynamics (CFD) studies on combustion and radiation heat transfer from a real radiant tube heater. The temperature along the radiant tube as well as at different positions in a test room has been measured. A good agreement between the experimental and predicted results has been found. Based on this validation, the effect of excess air, presented by Air Factor (AF) on efficiency of heater has been studied, theoretically. Moreover, the effect of inlet air preheating on heater efficiency has been examined. The results show that the higher values of excess air can reduce the heater efficiency. The air preheating temperature caused positive effect on heater efficiency. In addition, the results show at higher preheating temperature the effect of AF value on heater efficiency is negligible.     

Grooving as Alternative Method of Surface Preparation to Postpone Debonding of FRP Laminates in Concrete Beams

Structural repair and strengthening have long been dynamic and challenging activities in construction work. One of the most commonly used methods for such repairs is the application of fiber-reinforced polymer (FRP) sheets to strengthen RC or even steel structure members. A major issue of concern in flexural strengthening of RC beams with FRP laminates is the debonding of the concrete substrate, which leads to premature failure of the structural member thus strengthened. One reason for this premature rupture may be the lack of proper preparation of the concrete surface in contact with the FRP sheet. Surface preparation is typically associated with such constraints as adverse environmental impacts, economic losses due to stoppage of activities, repair costs, or even inaccessibility of the member(s) to be strengthened. This study aims to investigate surface preparation for application of FRP sheets in an attempt to develop substitute methods for conventional surface preparation methods. The experimental specimens used for the purposes of this study included a minimum of 100 prism specimens of dimensions 100×100×500?mm subjected to four-point flexural loading. The specimens were divided into the two control and experimental groups. The control group lacked FRP sheets, while the experimental one had FRP sheets tested for their ultimate failure strength as a result of both surface preparation and transverse, longitudinal, and diagonal grooves as substitutes for surface preparation. The results indicated that surface preparation prior to bonding of FRP sheets increased ultimate rupture strength. It was also found that the substitute preparation methods greatly compensated for the lack of conventional surface preparation such that they changed, in some cases, the ultimate failure behavior of the member.     

Control of morphological properties of porous biodegradable scaffolds processed by supercritical CO2 foaming

A low cost supercritical CO₂ foaming rig with a novel design has been used to prepare fully interconnected and highly porous biodegradable scaffolds with controllable pore size and structure that can promote cancellous bone regeneration. Porous polymer scaffolds have been produced by plasticising the polymer with high pressure CO₂ and by the formation of a porous structure following the escape of CO₂ from the polymer. Although, control over pore size and structure has been previously reported as difficult with this process, the current study shows that control is possible. The effects of processing parameters such as CO₂ saturation pressure, time and temperature and depressurisation rate on the morphological properties, namely porosity, pore interconnectivity, pore size and wall thickness- of the scaffolds have been investigated. Poly(d,l)lactic acid was used as the biodegradable polymer. The surfaces and internal morphologies of the poly(d,l)lactic acid scaffolds were examined using optical microscope and micro computed tomography. Preosteoblast human bone cells were seeded on the porous scaffolds in vitro to assess cell attachment and viability. The scaffolds showed a good support for cell attachment, and maintained cell viability throughout 7 days in culture. This study demonstrated that the morphology of the porous structure can be controlled by varying the foaming conditions, allowing the porous scaffolds to be used in various tissue engineering applications.     

Aliphatic polyurethane–montmorillonite nanocomposite coatings: Preparation,characterization, and anticorrosive properties

Polyurethane (PU)–clay nanocomposite coatings were prepared by a sonication method. The stability and morphology of these coatings was characterized by turbidometry, X‐ray diffraction, and transmission electron microscopy. The anticorrosive properties of these coatings were investigated by salt‐spray and electrochemical impedance spectroscopy methods. According to the results, dispersed nanoclay layers in the matrix of the nanocomposite coating compositions led to superior anticorrosive characteristics compared to those of pure PU coatings. The best results were obtained with coatings containing about 5 wt % clay. The resistance of the coating containing 5% clay was about 9.002 GΩ after 225 days of immersion in a 3.5 wt % NaCl solution, whereas it was only 97 kΩ for the pure PU coating. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis of magnesium hydroxide nanofiller and its use for improving thermal properties of new poly(ether‐amide)

A new poly(ether‐amide; PEA) as a source of polymeric matrix, containing flexible ether group in the main chain was synthesized by direct polycondensation reaction of 1,2‐(4‐carboxy phenoxy)ethane with 4,4‐diaminodiphenyl ether in a medium consisting of N‐methyl‐2‐pyrrolidone, triphenyl phosphite, calcium chloride, and pyridine. The resulting PEA was characterized by gel permeation chromatography (GPC), ¹H NMR and FT‐IR spectroscopy. Magnesium Hydroxide (MH) nanostructure was synthesized by the reaction of magnesium sulfate and sodium hydroxide by sonochemical method. The MH particle was characterized by X‐ray diffraction (XRD) and scanning electron microscopy (SEM). Then Mg(OH)₂ nanostructure was added to poly(ether‐amide) matrix and resulting nanocomposites were characterized by XRD, SEM, and Thermogravimetry Analysis (TGA). Thermal decomposition of the PEA shifted towards higher temperature in the presence of the magnesium hydroxide nanoparticles. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Electrochemical effects of silane pretreatments containing cerium nitrate on cathodic disbonding properties of epoxy coated steel

In the recent years, silane materials, because of their environmental friendly nature and ease of application have been attended as an alternative for chromate conversion coatings. Different materials were searched for improvement of the efficiency of silane formulation. In this research, pretreatment of carbon steel substrates was carried out using γ-glycidoxypropyl-trimethoxysilane (γ-GPS) as functionalized silane. Cerium nitrate as a corrosion inhibitor material was introduced into the silane material and epoxy resin was applied on the pretreated steel substrates. Effects of the pretreatment on electrochemical properties, cathodic disbondment, dry and wet adhesion strength, and surface morphology of resultant epoxy coating were investigated. Results showed that pretreatment of steel substrate with γ-glycidoxypropyl-trimethoxysilane (γ-GPS) doped with cerium nitrate leads to improvement of cathodic disbondment and also dry and wet adhesion of epoxy coating. Furthermore, this type of pretreatment reduced the disruption of interfacial bonds at the binder/substrate interface. Addition of 2?wt% cerium nitrate into the silane formulation led to the maximum efficiency of resultant coating.     

CuIns2/Cus Nanocomposite: Synthesis via Simple Microwave Approach and Investigation Its Behavior in Solar Cell

CuInS₂/CuS nanocomposite were synthesized by a copper complex, [bis(ethylenediamine)copper(ΙΙ)] sulfate. Eight sulfur sources were used for this experiment. The products were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray analysis spectroscopy, and room temperature photoluminescence spectroscopy. Thin film of nanocomposite powder was fabricated and its feature (V_oc, J_sc and FF) was calculated by current–voltage (I–V) curve.     

A comparative study on optimised and non‐optimised axial flow,spherical reactors in naphtha reforming process

In this study, the operating conditions of an axial flow spherical reactor have been optimised using a reliable optimisation technique and the results are compared with the results of non‐optimised conditions. The dynamic behaviour of the reactor has been considered in the optimisation process and orthogonal collocation method has been used in order to solve the obtained equations from mathematical modelling of the process. The goal of this study is to maximise the aromatics and hydrogen production rate. Therefore, the objective function is the combination of two terms which include the production rate of the mentioned components. The catalyst distribution for each reactor, the inlet pressure of the system, Length per radius for each reactor, the naphtha feed molar flow rate and the hydrogen mole fraction in the recycle stream as well as the inlet temperature of each reactor have been optimised in this study. © 2011 Canadian Society for Chemical Engineering     

The effect of MIO pigments on corrosion resistance and adhesion of synthetic rubber-based primer

In this research, the corrosion resistance and adhesion property of a synthetic rubber-based primer reinforced with different ratios of micaceous iron oxide (MIO) pigments were studied. Coatings were applied on carbon steel panels and also on steel pipes of 219.1 mm outer diameter. Scanning electron microscopy (SEM) was used to investigate the dispersion of MIO particles in the rubbery matrix. The anticorrosion performance of the coatings was studied, using electrochemical impedance spectroscopy (EIS) and salt spray tests. In addition, the adhesion of primers to carbon steel substrates was evaluated by pull-off test. In order to investigate the effect of MIO particles on the flexibility of the pigmented primers, a cupping test was conducted. The adhesion of cold-applied tape to the formulated primers was assessed by peel adhesion test using hanging mass method. The results indicated that adding 5, 10, and 15 wt% of MIO pigments into the primer improved corrosion resistance of the coatings. An increase in the MIO loading up to 10 wt%, improved the adhesion of the primer to both steel substrate and cold-applied tape.