Differential current switch logic: a low power DCVS logic family

Differential current switch logic (DCSL), a new logic family for implementing clocked CMOS circuits, has been developed. DCSL is in principle a clocked differential cascode voltage switch logic circuit (DCVS). The circuit topology outlines a generic method for reducing internal node swings in clocked DCVS logic circuits. In comparison to other forms of clocked DCVS, DCSL achieves better performance both in terms of power and speed by restricting internal voltage swings in the NMOS tree. DCSL circuits are capable of implementing high complexity high fan-in gates without compromising gate delay. Automatic lock-out of inputs on completion of evaluation is a novel feature of the circuit. Three forms of DCSL circuits have been developed with varying benefits in speed and power. SPICE simulations of circuits designed using the 1.2 μm MOSIS SCMOS process indicate a factor of two improvement in speed and power over comparable DCVS gates for moderate tree heights     

A local theory of heating in cross-ply carbon fiber thermoplastic composites by magnetic induction

For joining and repair of continuous fiber thermoplastic composites, induction heating has been viewed a strong candidate. Induction heating employs an applied alternating magnetic field, which induces a rotational emf in a grid of conductive carbon fibers, which are then used to carry resulting currents. In continuous carbon fiber crossply composites the available paths for “eddy current” loops are along the network of conductive carbon fibers. For this to occur, an electrical transfer must take place between crossing fibers in adjacent plies. Tests involving variable thicknesses of interply neat film layers have been performed to provide insight into the mechanisms taking place. These tests indicate that the primary mechanism for heating in such laminates is dielectric losses in the polymeric region between fibers in adjacent planes that form the conductive loop. Therefore, heating is not uniform in such composites despite a uniform magnetic flux. Heating patterns were viewed using liquid crystal materials and E-type thermocouples. Several factors leading to nonhomogeneous thermal distributions have been considered, including current density effects, internal emf cancellation, and rotational field effects. Global and local considerations are addressed, a localized model is proposed, and the corresponding theory is developed qualifying the early results. Additional testing has supported the theory.     

Thermal stability in bulk cryomilled ultrafine-grained 5083 Al alloy

Thermal stability in bulk ultrafine-grained (UFG) 5083 Al that was processed by gas atomization followed by cryomilling, consolidation, and extrusion, and that exhibited an average grain size of 305 nm, was investigated in the temperature range of 473 to 673 K (0.55 to 0.79 T _m , where T _m is the melting temperature of the material) for different annealing times. Appreciable grain growth was observed at temperatures > 573 K, whereas there was limited grain growth at temperatures < 573 K even after long annealing times. The values of the grain growth exponent, n, deduced from the grain growth data were higher than the value of 2 predicted from elementary grain growth theories. The discrepancy was attributed to the operation of strong pinning forces on boundaries during the annealing treatment. An examination of the microstructure of the alloy suggests that the origin of the pinning forces is most likely related to the presence of dispersion particles, which are mostly introduced during cryomilling. Two-grain growth regimes were identified: the low-temperature region (<573 K) and the high-temperature region (>573 K). For temperatures lower than 573 K, the activation energy of 25 ± 5 kJ/mol was determined. It is suggested that this low activation energy represents the energy for the reordering of grain boundaries in the UFG material. For temperatures higher than 573 K, an activation energy of 124 ± 5 kJ/mol was measured. This value of activation energy, 124 ± 5 kJ/mol, lies between that for grain boundary diffusion and lattice diffusion in analogous aluminum polycrystalline systems. The results show that the strength and ductility of bulk UFG 5083 Al, as obtained from tensile tests, correlate well with substructural changes introduced in the alloy by the annealing treatment.     

Electrical and optical studies of ZnO:Ga thin films fabricated via the sol–gel technique

The effects of dopant (Ga) concentration, post-heat treatment temperatures, and different heat treatment environments on the morphology, electrical and optical properties of ZnO films were studied. ZnO films doped with Ga are derived from non-alkoxide zinc acetate via the alcoholic route by a sol–gel dip-coating technique. Introduction of Ga, as a dopant, can reduce crystallite size, which is attributed to the increased number of nucleation centers. Grain growth was also observed at high post-heat treatment temperature. It was discovered that different post-heat treatment environments (air or reduced atmosphere) did not change the structure orientation, microstructure shapes and size. It was found that the sheet resistance, R_s could be reduced by an order of magnitude, using post-heat treatment in reduced atmosphere (4%H₂–96%N₂).     

Regeneration studies on nickel molybdate catalysts used for the upgrading of coal-derived liquids

Nickel molybdate catalysts used in several different upgrading reactions of coal-derived materials from low-rank Australian coals have been regenerated and their activity assessed using a number of physical and chemical techniques. Regeneration of spent coked catalysts for 20 hours in air at 450°C was sufficient to restore chemical hydrogenation activity to catalyst used for pre-asphaltene, asphaltene and oil upgrading, provided poisoning of the catalyst surface by other impurities, principally chlorine-containing molecules, had not occurred.     

Origin of visible photoluminescence from porous silicon as studied by Raman spectroscopy

In this paper we discuss the different models proposed to explain the visible luminescence in porous silicon (PS). We review our recent photoluminescence and Raman studies on PS as a function of different preparation conditions and isochronal thermal annealing. Our results can be explained by a hybrid model which incorporates both nanostructures for quantum confinement and silicon complexes (such as SiH _x and siloxene) and defects at Si/SiO₂ interfaces as luminescent centres.     

On joint transmitter and receiver optimization formultiple-input-multiple-output (MIMO) transmission systems

The problem of joint transmitter and receiver optimization for MIMO systems under the mean-squared error (MSE) criterion is revisited. We address the general problem of N (number of users) ≠M (number of channel inputs) ≠P (number of channel outputs) when the system is Nyquist bandlimited and obtain analytical solutions for the optimal transmit-receive pair. Next, we demonstrate how the above result is directly applicable to the problem where the system has excess bandwidth, thereby generalizing the results of Salz (1985). In conclusion, several numerical examples are included to demonstrate the performance gains obtainable with jointly optimized MIMO systems vis-a-vis systems based only on receiver optimization     

Design of linear phase FIR filters using the LMS algorithm

The application of the stochastic gradient (least mean square) algorithm, the design of linear phase finite impulse response (FIR) filters, is discussed. Analytical results are presented and supported by simulation experiments to demonstrate the superior performance of the LMS algorithm equipped with the linear phase constraint as compared to the standard LMS algorithm