One-side value-added service investment and pricing strategies for a two-sided platform

To widen user participation and increase profit, two-sided platforms may invest on value-added services (VASs) for users. Due to the cross-market network externality, the investment for one side would affect the utility of users on two sides, thus affect the demand and profit of the platform. In this paper, we investigate one-side VAS investment and pricing strategies for a two-sided platform. It is revealed that it is optimal to invest at the maximum level for any marginal investing cost below a certain threshold, and to decrease the investment when the marginal investing cost increases above the threshold. We find that compared with the case of no investment, the invested user side will always be priced higher, while the uninvested user side may either be priced higher or lower, depending on the relative magnitude of mutual cross-market network externalities. If both sides are priced higher after the investment, the price increment for uninvested user side could be larger than that for invested user side.     

含纳米Co的新型PDC复合片性能试验研究

提出了用纳米钴代替微米钴作为粘结剂的PDC复合片制备新方法及配套的制备新工艺,并对新型PDC复合片的微观组织结构及性能进行了研究。微观分析结果表明,纳米钴较于微米钴更密实地填充在金刚石颗粒间,有效促进了金刚石颗粒间D-D键的形成,且添加纳米钴的金刚石层对金刚石颗粒的把持力更好,同时纳米钴在金刚石层中形态较小且分布均匀,这些均对提高复合片综合性能有积极作用。性能测试结果表明,相对于传统复合片,新型复合片抗冲击性能提高了1.13倍,其耐磨性和热稳定性也得到了一定的提高,这与微观分析的结论一致。研究成果不仅为提升复合片综合性能提供了新思路,也对实现钻井提速增效、提高PDC钻头使用寿命有重要意义。     

Engineering High‐Performance MoO2‐Based Nanomaterials with Supercapacity and Superhydrophobicity by Tuning the Raw Materials Source

Herein, a simple self‐assembly method is proposed for the fabrication of MoO₂‐based superhydrophobic material with record high contact angles (contact angle up to about 173°) for conductive metal oxides on hard/soft substrates. The spin‐coated surface demonstrates excellent oil–water separation efficiency (>98%) after 50 cycles and robust corrosion resistance after immersion into different pH solutions for 20 d. These water‐resistant coatings retain excellent superhydrophobicity after oil immersion, knife‐scratch, and long‐cycle sandpaper abrasion, which is not observed on most artificial surfaces. Meanwhile, the functionality switching from superhydrophobicity to supercapacity, which have an inverse relationship in aqueous solutions because of poor electrode wettability, is achieved simply by editing the raw materials source. Tuning of the raw materials leads to the same product MoO₂/graphitic carbon with different morphologies and functionalities. Different from superhydrophobic MoO₂/carbon ball flowers, MoO₂ nanotubes with carbon exhibit excellent supercapacity with a large gravimetric capacitance and great cycling stability.     

Fabrication of Titanium Aluminides via Powder-Cored Wire Arc Additive Manufacturing: Microstructural and Mechanical Characterization

Herein, an innovative powder-cored wire arc additive manufacturing (PC-WAAM) process is proposed to fabricate γ-TiAl thin-walled intermetallic alloy. The metallography, phase composition, and mechanical properties at different thin-wall locations are characterized. The results show that the alternatively distributed layer-like microstructure composed of α₂ (Ti₃Al) and γ (TiAl) phases is obtained along the building direction. The content of α₂ phase exhibits the tendency of decreasing from the bottom to top region. This unique microstructure characteristic is closely related to the typical thermal cycling history during deposition. Moreover, the tensile strength and microhardness of the top region are lower than the middle and bottom region. In general, the current PC-WAAM technique shows promising capability of fabricating γ-TiAl intermetallic alloy with low cost. This work becomes a valuable reference for understanding the evolution mechanism of microstructure and paves the way for the flexible and customized additive manufacturing of γ-TiAl alloy.     

Quantitative analysis of metabolic gases by multichannel Raman spectroscopy: use of a newly designed elliptic-spherical integration type of cell holder

We describe the quantitative analysis of some metabolic gases bymultichannel Raman spectroscopy. Raman spectra were measured forair, acetone, ammonia, carbon dioxide, and mixed gas consisting ofacetone, ammonia, and air. We designed a new elliptic-sphericalintegration type of cell holder to obtain the Raman spectra of gaseswith a high signal-to-noise ratio. Concentrations of acetone, ammonia, and carbon dioxide were determined by the peak intensities ofRaman bands at 2940, 3228, and 1385 cm(-1), respectively. To compensate for the fluctuations of Ramanintensities caused by several factors, such as the fluctuations oflaser power, the peak intensity of a band at 2324 cm(-1) dueto nitrogen gas was used as an internal intensity standard. Thecorrelation coefficient between the corrected Raman intensity at 2940cm(-1) and the concentration of acetone was calculated to be0.984 for a concentration range of 2-12 ppm. The detection limitof acetone gas was found to be 2 ppm.     

Study of delay-independent decentralized guaranteed cost control for large scale systems

This study introduces delay independent decentralized guaranteed cost control design method based on two controller structures for nonlinear uncertain interconnected large scale systems with time delays. First, a set of equivalent Takagi-Sugeno (T-S) fuzzy models are extended to represent the systems. Then a decentralized state-feedback guaranteed cost performance controller is proposed for the fuzzy systems. Based on delay independent Lyapunov functional approach, some sufficient conditions for the existence of the controller can be cast into the feasible problem of LMIs irrespective of the sizes of the time delays so that the system can be asymptotically stabilized for all considered uncertainties whose sizes are not larger than their bounds. Finally, the minimizing approach is proposed to search the suboptimal upper bound value of guaranteed cost function. Moreover, the corresponding conditions are extended into the generalized dynamic output-feedback close-loop system. Finally, the better control performances of the proposed methods are shown by the simulation examples.     

均衡不完全区组设计的满秩LDPC码构造及快速编码

为了降低准循环低密度奇偶校验（Low-Density Parity-Check,LDPC）码编码的复杂度,提出了一种基于均衡不完全区组设计（Balanced Incomplete Block Designs,BIBD）满秩LDPC码的构造及快速编码方法。基于BIBD构造的满秩校验矩阵可以快速得到系统循环阵形式的生成矩阵。此方案设计不但可以实现线性化编码,而且编出的码字都为系统码。仿真结果表明,构造出的LDPC码具有很好的误码率性能和收敛特性,而其满秩的编码方法具有较好的通用性和实用价值。     

Digital time‐modulation pixel memory circuit in LTPS technology

Abstract— A digital time‐modulation pixel memory circuit on glass substrate has been designed and verified for a 3‐μm low‐temperature polysilicon (LTPS) technology. From the experimental results, the proposed circuit can generate 4‐bit digital codes and the corresponding inversion data with a time‐modulation technique. While the liquid‐crystal‐display (LCD) panel operates in the still mode, which means the same image is displayed on the panel, a data driver for an LCD panel is not required to provide the image data of the frame by the proposed pixel memory circuit. This pixel memory circuit can store the frame data and generate its corresponding inversion data to refresh a static image without activating the data driver circuit. Therefore, the power consumption of a data driver can be reduced in the LCD panel.     

Near-Entropy Hotlink Assignments

Consider a rooted tree T of arbitrary maximum degree d representing a collection of n web pages connected via a set of links, all reachable from a source home page represented by the root of T. Each web page i carries a probability p _i representative of the frequency with which it is visited. By adding hotlinks—shortcuts from a node to one of its descendents—we wish to minimize the expected number of steps l needed to visit pages from the home page, expressed as a function of the entropy H(p) of the access probabilities p. This paper introduces several new strategies for effectively assigning hotlinks in a tree. For assigning exactly one hotlink per node, our method guarantees an upper bound on l of 1.141H(p)+1 if d>2 and 1.08H(p)+2/3 if d=2. We also present the first efficient general methods for assigning at most k hotlinks per node in trees of arbitrary maximum degree, achieving bounds on l of at most \frac2H(p)log(k+1)+1\frac{2H(p)}{\log(k+1)}+1 and \fracH(p)log(k+d)-logd+1\frac{H(p)}{\log(k+d)-\log d}+1 , respectively. All our methods are strong, i.e., they provide the same guarantees on all subtrees after the assignment. We also present an algorithm implementing these methods in O(nlog n) time, an improvement over the previous O(n ²) time algorithms. Finally we prove a Ω(nlog n) lower bound on the running time of any strong method that guarantee an average access time strictly better than 2H(p).     

基于小波分析的交通数据自适应消噪算法研究

针对实际采样环境中存在的各种干扰,以及交通数据的非平稳特性,在交通数据小波变换特性分析的基础上,提出基于小波分析的交通数据自适应消噪算法:对交通数据进行小波分解,然后对高频系数的自相关函数进行白噪声检验,从而确定小波分解的层数和阈值。采用实际检测交通流数据,对算法的有效性进行了验证分析。