1/f noise in large-area Hg<Subscript>1−x</Subscript>Cd<Subscript>x</Subscript>Te photodiodes

The 1/f noise in photovoltaic (PV) molecular-beam epitaxy (MBE)-grown Hg_1−xCd_xTe double-layer planar heterostructure (DLPH) large-area detectors is a critical noise component with the potential to limit sensitivity of the cross-track infrared sounder (CrIS) instrument. Therefore, an understanding of the origins and mechanisms of noise currents in these PV detectors is of great importance. Excess low-frequency noise has been measured on a number of 1000-μm-diameter active-area detectors of varying “quality” (i.e., having a wide range of I-V characteristics at 78 K). The 1/f noise was measured as a function of cut-off wavelength under illuminated conditions. For short-wave infrared (SWIR) detectors at 98 K, minimal 1/f noise was measured when the total current was dominated by diffusion with white noise spectral density in the mid-10⁻¹⁵A/Hz^1/2 range. For SWIR detectors dominated by other than diffusion current, the ratio, α, of the noise current in unit bandwidth i_n(f = 1 Hz, V_d = −60 mV, and Δf = 1 Hz) to dark current I_d(V_d = −60 mV) was α_SW-d = i_n/I_d ∼ 1 × 10⁻³. The SWIR detectors measured at 0 mV under illuminated conditions had median α_SW-P = i_n/I_ph ∼ 7 × 10⁻⁶. For mid-wave infrared (MWIR) detectors, α_MW-d = i_n/I_d ∼ 2 × 10⁻⁴, due to tunneling current contributions to the 1/f noise. Measurements on forty-nine 1000-μm-diameter MWIR detectors under illuminated conditions at 98 K and −60 mV bias resulted in α_MW-P = i_n/I_ph = 4.16 ± 1.69 × 10⁻⁶. A significant point to note is that the photo-induced noise spectra are nearly identical at 0 mV and 100 mV reverse bias, with a noise-current-to-photocurrent ratio, α_MW-P, in the mid 10⁻⁶ range. For long-wave infrared (LWIR) detectors measured at 78 K, the ratio, α_LW-d = i_n/I_d ∼ 6 × 10⁻⁶, for the best performers. The majority of the LWIR detectors exhibited α_LW-d on the order of 2 × 10⁻⁵. The photo-induced 1/f noise had α_LW-P = i_n/I_ph ∼ 5 × 10⁻⁶. The value of the noise-current-to-dark-current ratio, α appears to increase with increasing bandgap. It is not clear if this is due to different current mechanisms impacting 1/f noise performance. Measurements on detectors of different bandgaps are needed at temperatures where diffusion current is the dominant current. Excess low-frequency noise measurements made as a function of detector reverse bias indicate 1/f noise may result primarily from the dominant current mechanism at each particular bias. The 1/f noise was not a direct function of the applied bias.     

Characteristic Features of the Optimal Processing of the Results of Measurements in the Case of a Random Observation Function

An analysis is made of the characteristic features and problems of the optimal processing of the results of measurements in the case of a random observation function utilizing a nonlinear Kalman filter. A method is proposed for increasing the convergence domain of the filter with additional processing of measurements in the frequency domain.     

Inside Front Cover: The Elastic Properties and Plastic Behavior of Two‐Dimensional Polymer Structures Fabricated by Laser Interference Lithography (Adv. Funct. Mater. 10/2006)

The probing of the micromechanical properties within a two‐dimensional polymer structure with sixfold symmetry fabricated via interference lithography reveals a nonuniform spatial distribution in the elastic modulus “imprinted” with an interference pattern in work reported by Tsukruk, Thomas, and co‐workers on p. 1324. The image prepared by M. Lemieux and T. Gorishnyy shows how the interference pattern is formed by three laser beams and is transferred to the solid polymer structure. The elastic and plastic properties within a two‐dimensional polymer (SU8) structure with sixfold symmetry fabricated via interference lithography are presented. There is a nonuniform spatial distribution in the elastic modulus, with a higher elastic modulus obtained for nodes (brightest regions in the laser interference pattern) and a lower elastic modulus for beams (darkest regions in the laser interference pattern) of the photopatterned films. We suggest that such a nonuniformity and unusual plastic behavior are related to the variable material properties “imprinted” by the interference pattern.     

Spinel Phase Relations in the Fe3O4–CuFe2O4 System

Phase equilibria involving spinel solid solutions, delafossite, and hematite in the Fe–Cu–O system are studied by emf measurements in solid-electrolyte galvanic cells. The results demonstrate that, above 1250 K, Fe₃O₄ and CuFe₂O₄ form a continuous series of solid solutions. At lower temperatures, the solid solution disproportionates with the formation of delafossite and Fe₂O₃, and two spinel solid solutions appear: one based on Fe₃O₄ and the other based on Cu₂FeO₄. The compositions of the spinel phases in equilibrium with delafossite and Fe₂O₃ are determined in the range 1100–1250 K.     

Management gaps analysis: a case study of groundwater resource management in New Zealand

The primary objective of this project is to identify gaps, whether real or perceived, that hinder effective groundwater management in New Zealand. These gaps show as gaps in information, gaps in implementation, gaps in technological and management tools, and gaps in understanding of fundamental processes. The secondary objective is to propose a management strategy to close the identified gaps. Several methods are used to meet these objectives: surveys distributed to selected staff in each regional council; the review of various written reports; the analysis of land-use databases; and private consultation within each regional council. Results show that groundwater management in New Zealand is generally reactionary with the main gaps being in strategic planning and national guidelines. Most gaps appear to be predominantly information and implementation issues. In some cases there are gaps in the understanding of fundamental processes within an aquifer system, including the long-term effects of land-use on groundwater quality. An adaptive management approach is suggested as a means of closing these gaps.     

Modeling aviation baggage screening security systems: a case study

Aviation security protects vital national interests, as well as passengers and aircraft. Key components of an aviation security system include baggage and passenger screening devices and operations. Determining how and where to assign (deploy) such devices can be quite challenging. Moreover, even after such systems are in place, it can be difficult to measure their effectiveness. This paper describes how discrete optimization models can be used to address these questions, based on three performance measures that quantify the effectiveness of airport baggage screening security device systems. These models are used to solve for optimal airport baggage screening security device deployments considering the number of passengers on a set of flights who have not been cleared using a security risk assessment system in use by the Federal Aviation Administration (i.e., passengers whose baggage is subjected to screening), the number of flights in this set, and the size of the aircraft for such flights. Several examples are provided to illustrate these results, including an example that uses data available from the Official Airline Guide.     

Fifty Years On: Brown v. Board of Education and American Psychology, 1954-2004 An Introduction.

Introduces the current issue of the American Psychologist, which examines the ramifications of the Brown vs. Board of Education decision and its sequelae over the last 50 years, with a special focus on the mixed role of psychological research and practice. Despite the great strides toward a more just society since May 17, 1954, inequities remain in schooling, in social relations, and in economic opportunity. How will history judge American psychology 50 years from now vis-a-vis the possibilities it helped create via Brown? The articles in this special issue suggest several important directions of research and action our field will need to take if the verdict of history is to be a positive one. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

A new microcalorimeter for measurements in 3.5-mm coaxial line

A new microcalorimeter has been realized for implementing the national power standard up to 26.5 GHz in a 3.5-mm coaxial line at the Istituto Elettrotecnico Nazionale (IEN) Galileo Ferraris, Turin, Italy. The system is based on a dry thermostatic cell controlled by Peltier elements. The thermal load consists of a twin sensor system that is alternately supplied with high frequency test power and low frequency or direct current (DC) reference power through adiabatic coaxial lines. This microcalorimeter was originally designed for calibrating bolometric mounts. Recently, it has been modified for thermocouple power sensors, which can operate from DC to 26.5 GHz in a 3.5-mm coaxial line.