A small-angle X-ray scattering study of powder compaction

This work demonstrated a novel and potentially important application of two-dimensional small-angle X-ray scattering (2D-SAXS) to investigate powder compaction. SAXS from powder compacts of three materials commonly used for pharmaceutical tabletting exhibited azimuthal variations, with stronger intensity in the direction of the applied compaction force, relative to the transverse direction. This implied that compaction of a (macroscopic) powder could also produce changes on the molecular (nanometre) scale, which can be probed by 2D-SAXS. Two possible explanations for this effect were suggested. A combination of anisometric (i.e. elongated or flattened) granules with anisotropic morphologies could result in azimuthal variation in X-ray scattering due to granule orientation. It is expected that this mechanism would require relatively low packing density, so may operate during die filling. Granule re-orientation appeared less likely at higher packing densities and compaction pressures, however. Under these conditions, the changes in the 2D-SAXS patterns would be consistent with the powder granules becoming relatively flattened in the compression direction, with corresponding changes in their nano-scale morphology. The magnitude of this effect was found to vary between the materials used and increased with compaction pressure. This suggested that 2D-SAXS studies could provide useful information on force-transmission within a compressed powder. Further analysis of the data also suggested differences in the compaction mechanisms (i.e. granule re-orientation, deformation or fragmentation) between the materials studied.     

Some sulfides of gold and silver: Composition,mineral mineral assemblage,and conditions of formation

Characteristic mineral assemblage and special features of the composition of Au and Ag sulfides of gold-silver deposits have been established. The forms of the occurrence of Au and Ag in the minerals of the early and last stages have been analyzed. The conditions for the formation of uytenbogaardtite and petrovskaite in supergene and low-temperature hydrothermal processes have been considered. A thermodynamic model explaining their genesis in the oxidation zones is presented.     

Kinetics of the reaction of olefin synthesis from methanol and dimethyl ether

The kinetics of the reaction of olefin synthesis from dimethyl ether and methanol is studied. A kinetic model of the nine-route reaction under study is constructed. The constants of the model are estimated using experimental data. The adequacy of the model to the results of experiments is shown     

Corundum concretes based on modified phosphate-containing binders

Physicotechnical properties are provided for concretes based on mechanically-activated phosphate suspensions previously modified with magnesium and aluminum hydroxides and silicic acid. The results obtained demonstrate the efficiency of using modifying additions in order to increase the strength and heat resistance of corundum concretes. Translated from Novye Ogneupory, No. 5, pp. 32–35, May 2008.     

Online and Offline Rotary Regression Analysis of Torque Estimator for Switched Reluctance Motor Drives

A new torque estimator for switched reluctance motor (SRM) drives based on 2-D rotary regression analysis is presented in this paper. The proposed torque estimator is composed of a bicubic regressive polynomial as a function of rotor position and input current. The regressive coefficients can be computed offline or online from the torque characteristics acquired either experimentally or from numerical computation. Furthermore, a torque estimation method by taking mutual coupling into consideration is proposed. It can be seen that the estimated and experimentally obtained self-coupling and mutual-coupling torque characteristics are in good agreement with each other. In addition, the dynamic torque waveforms with and without the mutual coupling, estimated by the proposed estimator, are found to be virtually the same as those obtained from the bicubic spline interpolation for SRM drives with single-pulse voltage, hysteresis current chopping, as well as with voltage pulse width modulation control. The success of all the case studies being reported is a good validation of the usefulness and accuracy of the proposed real-time torque estimator that, as described in this paper, can be used to quickly estimate the instantaneous output torque of SRM drives.     

Optical properties of doped bismuth telluride crystals in the region of plasma effects

The optical properties of bismuth telluride crystals doped with donor-and acceptor-type impurities are studied. The fact that energy corresponding to the resonance frequency of plasma oscillations of free charge carriers (plasmons) approaches the band-gap energy is detected in the infrared spectral region, where the main elementary excitations in the electronic system of these materials are observed. The mentioned approach of energies varies the intensity of electron-plasmon interaction, which affects the recombination processes in the materials widely used for the fabrication of thermoelectric energy converters.     

Synthesis and physicochemical characterization of a well-defined poly(butadiene 1,3)-block-poly(dimethylsiloxane) copolymer

For the first time, order-order and order-disorder transitions were detected and characterized in a model diblock copolymer of poly(butadiene-1,3) and poly(dimethylsiloxane) (PB-b-PDMS). This model PB-b-PDMS copolymer was synthesized by the sequential anionic polymerization (high vacuum techniques) of butadiene 1,3 (B) and hexamethylciclotrisiloxane (D₃), and subsequently characterized by nuclear magnetic resonance (¹H and ¹³C NMR), size exclusion chromatography (SEC), Fourier Transform infrared spectroscopy (FTIR), Small-Angle X-ray scattering (SAXS) and rheology. SAXS combined with rheological experiments shows that the order-order and order-disorder transitions are thermoreversible. This fact indicates that the copolymer has sufficient mobility at the timescale and at the temperatures of interest to reach their equilibrium morphologies.     

3D velocity from 3D Doppler radial velocity

We present local least squares and regularization frameworks for computing 3D velocity (3D optical flow) from 3D radial velocity measured by a Doppler radar. We demonstrate the performance of our algorithms quantitatively on synthetic radial velocity data and qualitatively on real radial velocity data, obtained from the Doppler radar at Kurnell Radar station, Botany Bay, New South Wales, Australia. Radial velocity can be used to predict the future positions of storms in sequences of Doppler radar datasets.© 2005 Wiley Periodicals, Inc. Int J Imaging Syst Technol, 15, 189–198, 2005     

Thomson scattering diagnostic systems in the ITER divertor

A diagnostic array has been developed for studying the operating modes of the divertor in the ITER tokamak-reactor using the Thomson scattering technique. The aim of this study is to measure the spatial profiles of the electron temperature and density. The structure of the diagnostic setup was selected on the basis of a classical diagnostic geometry and the high-resolution LIDAR system, which provide access to different regions of the divertor plasma. A severe radiation environment, limited access to the plasma in the ITER divertor, and a high-dust environment (the divertor plate erosion material) in the divertor volume pose many problems for performing diagnostics under unique conditions having no analogs in the tokamaks that are now in operation. Different methods for protecting optical surfaces from plasma-enriched deposition are proposed and analyzed. The efficiency of these methods has been demonstrated in bench tests. The concept of laser and detector systems and diffraction polychromators capable of operating at different electron temperatures with a lower limit of 1 eV, has been justified and approved.