High-gain pseudomorphic InGaAs base ballistic hot-electron device

A high-gain ballistic hot-electron device is described. The GaAs-AlGaAs heterostructure device, with a 21-mm-thick pseudomorphic In _0.12Ga_0.88As base, had a current gain of 27 at 77 K and 41 at 4.2 K. As characteristically seen in ballistic devices, transfer into the L valley limited the maximum gain. The Γ-L valley separation in the strained In_0.12Ga_0.88As was estimated to be about 380 meV     

The impact of new product development acceleration approaches on speed and profitability: lessons for pioneers and fast followers

This work investigates the impact of nine new product development (NPD) acceleration approaches (supplier involvement, lead user involvement, speeding up activities and tasks, reduction of parts and components, training and rewarding of employees, implementation of support systems and techniques, stimulating interfunctional cooperation, emphasis on the customer, and simplification of organizational structure) on development speed and new product profitability. Our findings from 233 manufacturing firms show that lead user involvement and training/rewarding of employees increase both development speed and profitability. Supplier involvement, speeding up activities and tasks, and a simplification of the organizational structure also enhance development speed, while an emphasis on the customer has an additional positive impact on new product profitability. Both new product speed and profitability increase firm financial performance. Our results further show that pioneers and fast followers should not select the same NPD acceleration approaches as the speed and profitability impact of the majority of the acceleration approaches depends on the new product strategy of the firm. These results are important as they provide guidance for pioneers and fast followers regarding which NPD acceleration approaches to select in order to enhance speed and profitability and, hence, firm financial performance.     

An integrated system to remote monitor and control anaerobic wastewater treatment plants through the internet.

The TELEMAC project brings new methodologies from the Information and Science Technologies field to the world of water treatment. TELEMAC offers an advanced remote management system which adapts to most of the anaerobic wastewater treatment plants that do not benefit from a local expert in wastewater treatment. The TELEMAC system takes advantage of new sensors to better monitor the process dynamics and to run automatic controllers that stabilise the treatment plant, meet the depollution requirements and provide a biogas quality suitable for cogeneration. If the automatic system detects a failure which cannot be solved automatically or locally by a technician, then an expert from the TELEMAC Control Centre is contacted via the internet and manages the problem.     

The effect of plastic deformation on Al2CuLi (T 1) precipitation

The enhancement ofT ₁ precipitation in Al-Li-Cu alloys by plastic deformation prior to aging (that is, cold work) and the subsequent increase in alloy strength is investigated. The increased understanding of the role of matrix dislocations in the nucleation and growth ofT ₁ plates, discussed in the previous paper,^[1] permits a detailed study of the phenomenon. In this paper, the effect of different levels of plastic strain on theT ₁ particle distributions as a function of aging time at 190 °C is quantified, and the subsequent influence on tensile properties is thereby described. The effect of plastic deformation is shown to decrease theT ₁ plate length and thickness, increase the number density by almost two orders of magnitude, increase the yield strength by 100 MPa, while simultaneously reaching peak strength in 20 pct of the time required without plastic deformation. Formerly Graduate Student, Department of Materials Science, University of Virginia,     

Construction and performance of a multiparameter focal plane detector for use on a QMG/2 magnetic spectrometer

The design, construction and performance of a modular, two pressure focal plane detector, 550 mm long, 1000 mm deep and with an active height of 60 mm are described. The detector has been operated with ions ranging from 50 MeV ¹H to 200 MeV ³⁶S. Typical results achieved are 0.5 mm and 0.3° for the spatial and angular resolutions, and 0.7% and 3% for the total energy and energy loss measurements. A height signal is also provided.     

Electrochemical Faceting of polycrystalline platinum in HF solutions

The electrochemical faceting of polycrystalline (pc) platinum yielding a (100)-preferred oriented electrode surface was accomplished in HF solutions by applying to the pc platinum electrode a square wave potential perturbation at 1 kHz in the 0.2 to 1.3 V range (vs rhe). SEM patterns of the resulting surfaces were also obtained. For HF concentrations up to 2 M no appreciable influence of the electrolyte concentration on the electrochemical faceting was noticed. Otherwise, the voltammetric response of the (100)-type preferred oriented platinum surface in the H-adatom potential range when compared to previously reported data resulted remarkably sensitive to the electrolyte composition. The discussion of results was based on the non-equilibrium adsorption conditions for anions under the periodic perturbation.     

Epoxy paint failure in B-52 fuel tanks: Part II. Influence of DIEGME concentration in the fuel on the failure process

A model has been proposed to explain the failure of the original BMS10-39 epoxy paint on upper vertical surfaces in B-52 fuel tanks. The model involves interaction of the paint with DIEGME, a fuel system ice inhibitor (FSII) in jet fuel, that is distilled from the liquid fuel. In this communication, distillation experiments used to support the model are refined to better match the mass transfer of vapor from fuel in a B-52 fuel tank at close to room temperature. The interaction of these lower temperature distillates with the paint affirms the earlier model. On the basis of these experiments it is proposed that paint failure may be controlled or eliminated by reducing the level of DIEGME in the fuel. Proposed changes in military jet fuel composition are detailed.     

Asset-Management of Transformers Based on Condition Monitoring and Standard Diagnosis [Feature Article]

In this paper, a methodology is developed to use data acquisition derived from condition monitoring and standard diagnosis for rehabilitation purposes of transformers. The interpretation and understanding of the test data are obtained from international test standards to determine the current condition of transformers. In an attempt to ascertain monitoring priorities, the effective test methods are selected for transformer diagnosis. In particular, the standardization of diagnostic and analytical techniques are being improved that will enable field personnel to more easily use the test results and will reduce the need for interpretation by experts. In addition, the advanced method has the potential to reduce the time greatly and increase the accuracy of diagnostics. The important aim of the standardization is to develop the multiple diagnostic models that combine results from the different tests and give an overall assessment of reliability and maintenance for transformers.     

Total and Fractional Performance of Granular Dust Traps in Refractory Production

Methods are proposed for designing interpolation models for the preliminary determination and subsequent forecasting of general and fractional breakthrough coefficients for dust used with granular filters, as employed in energy-saving and high-performance dust trapping from technological gases and ventilation discharges in refractory production. The models are supplied with nomograms, which makes them widely suitable for experts working in environmental protection at refractory-producing organizations. The main factors are identified that influence the performance. The results are of interest to experts in related areas of industry such as building materials and engineering ceramics and so on. Translated from Novye Ogneupory, No. 4, pp. 64–67, April, 2008.     

Production and structural features of a water-soluble polysaccharide from a mutant strain of Agrobacterium sp.

We have developed a mutant strain derived from Agrobacterium sp. ATCC 31750, which produces a water-soluble polysaccharide having potential utility to the food, feed, pharmaceutical and cosmetic industries. A high concentration of product (15 g/L) is obtained by 48 h cultivation of the mutant strain under optimized fermentation conditions. The water-soluble polysaccharide obtained from cultures of the mutant strain beta82 has Glc:Man:Gal in approximate molar ratios of 5.8:6.7:1.0. The molecular weight of the polysaccharide was determined to be approximately 1000 kDa by HPSEC analysis. Linkage analysis contained 3-Glcp, 3-Manp, terminal Glcp and terminal Manp, as well as a small proportion of 3- and 3,4-Galp, and 4,6-Manp residues. Based on analyses using FT-IR and ¹³C NMR spectrometers, most glycosidic bonds joining these sugar residues are of the α-type, and acetyl groups are apparently attached to the polymer chain at random.