Measurements of Stress Intensity Factors of an Interface Crack Under Mixed Mode Loading

The optical method of caustics has been utilised to measure both the stress intensity factor for a crack lying along the interface of an aluminium/epoxy bimaterial specimen, and the mode mixity arising from the difference in the elastic properties across the interface. Measurements were carried out by using a novel modification to the method whereby caustics are produced and measured from both sides of the specimen, so compensating automatically for the distortion induced in the specimen due to misaligned loading fixtures. A flat reflective surface across the interface was obtained by adhering a reflective coating to the specimen. Verification that this coating does not affect measurement accuracy was obtained by comparing stress intensity factors measured from coated and uncoated monolithic aluminium specimens where good agreement was found to exist between both measurements.     

Performance evaluation of air-conditioning units

A limited selection of samples of small and medium size air-conditioning equipment being marketed or manufactured in Kuwait was tested in an internationally reputed laboratory. The actual performance results obtained from laboratory tests were analyzed and compared with the commercially available information from the manufacturers for the same selected units. The analysis indicated the quality of air-conditioning equipment available to the Kuwaiti user.     

Variable-bit-rate speech transmission using punctured convolutionalcodes

Rate (n-1)/n punctured convolutional codes are very effective in conjunction with embedded differential pulse code modulation (EDPCM) in variable-bit-rate speech transmission. The authors investigate the performance of this variable-bit-rate EDPCM system in terms of probability of bit error and audio signal-to-noise ratio (SNR) versus channel SNR in an additive white Gaussian noise and Rayleigh fading channel using soft-decision decoding for specific sets of code generators of punctured convolutional codes. The results show that different sets of code generators affect the performance in terms of both the probability of bit error and the audio SNR. Improvements were obtained in the cases of Gaussian nonfading and Rayleigh fading channels using soft-decision decoding     

Experimental densities for compressed R134a

This paper reports densities of compressed R134a (1,1,1,2-tetrafluoroethane) determined by using a contiuously weighed pycnometer at 20 K intervals between 180 and 380 K at pressures from slightly greater than the vapour pressure to 70 MPa. The results are accurate to within ±0.1%. Saturated liquid densities derived by extrapolation from the experimental values agree with other reported values to within ±0.3%.     

Effect of the addition of Fe2O3 and heat treatment duration on the magnetic susceptibility of V2O5-P2O5-B2O3 glass system

The effect of the addition of Fe₂O₃ and heat treatment duration on the magnetic susceptibility of vanadium borophosphate glass were studied. The magnetic susceptibility of glass samples was found to increase with increasing Fe₂O₃ content, which may be explained by the formation of the FeO₆ group and the change of Fe²⁺ to Fe³⁺ which has higher paramagnetic properties. No detectable changes in the magnetic susceptibility with heat treatment for the samples containing 0.0, 0.5 and 1.0 mol% Fe₂O₃ was observed. The magnetic susceptibility for the heat treated samples containing 2.5, 5.0 and 7.5 mol% Fe₂O₃ decreases sharply with increasing duration of heat treatment up to 6 h and then remains almost constant. The sharp decrease in magnetic susceptibility of 2.5 mol% Fe₂O₃ is attributed to the increase in the number of ferrous ions. The sharp decrease for samples containing 5.0 and 7.5 mol% Fe₂O₃ is attributed to the increase in the number of Fe³⁺ in tetrahedral co-ordination. The rate of crystallization owing to the heat treatment was calculated and was found to increase with increasing iron oxide content. The geometry of crystallization was found to be in three-, two-and one-dimension(s) for samples containing 2.5, 5.0 and 7.5 mol% Fe₂O₃, respectively.     

Detecting lamb waves with broadband acousto-ultrasonic signals in composite structures

Lamb waves can be produced and detected in ceramic matrix composites (CMC) and metal matrix composites (MMC) plates using the acousto-ultrasonic configuration employing broadband transducers. Experimental dispersion curves of lowest symmetric and lowest antisymmetric modes behave in a manner analogous to the graphite/polymer theoretical curves. In this study a basis has been established for analyzing Lamb wave velocities for characterizing composite plates. Lamb wave dispersion curves and group velocities were correlated with variations in axial stiffness and shear stiffness in MMC and CMC. For CMCs, interfacial shear strength was also correlated with the first antisymmetric Lamb mode.     

Competitive learning and soft competition for vector quantizerdesign

The authors provide a convergence analysis for the Kohonen learning algorithm (KLA) with respect to vector quantizer (VQ) optimality criteria and introduce a stochastic relaxation technique which produces the global minimum but is computationally expensive. By incorporating the principles of the stochastic approach into the KLA, a deterministic VQ design algorithm, the soft competition scheme (SCS), is introduced. Experimental results are presented where the SCS consistently provided better codebooks than the generalized Lloyd algorithm (GLA), even when the same computation time was used for both algorithms. The SCS may therefore prove to be a valuable alternative to the GLA for VQ design     

Failure analysis of a hot extrusion die used for Al-Li alloy processing

Al-Li alloys being developed as lighter, substitutes for conventional high strength Al alloys are to be processed by routine methods. During extrusion of a 8090 Al-Li alloy, the extrusion die container failed causing some alarm. This failed die container was analysed to examine if the failure was caused by interaction of Li diffusing out of Al-Li alloy with the carbides of die steel. The evidence, although not conclusive, is sufficient to exercise caution during such processing.