Platinum Binuclear Complexes as Phosphorescent Dopants for Monochromatic and White Organic Light‐Emitting Diodes

Efficient blue‐, green‐, and red‐light‐emitting organic diodes are fabricated using binuclear platinum complexes as phosphorescent dopants. The series of complexes used here have pyrazolate bridging ligands and the general formula C^∧NPt(μ‐pz)₂PtC^∧N (where C^∧N = 2‐(4′,6′‐difluorophenyl)pyridinato‐N,C^2′, pz = pyrazole ( 1 ), 3‐methyl‐5‐tert‐butylpyrazole ( 2 ), and 3,5‐bis(tert‐butyl)pyrazole ( 3 )). The Pt–Pt distance in the complexes, which decreases in the order 1 > 2 > 3 , solely determines the electroluminescence color of the organic light‐emitting diodes (OLEDs). Blue OLEDs fabricated using 8 % 1 doped into a 3,5‐bis(N‐carbazolyl)benzene (mCP) host have a quantum efficiency of 4.3 % at 120 Cd m^–2, a brightness of 3900 Cd m^–2 at 12 V, and Commission Internationale de L'Eclairage (CIE) coordinates of (0.11, 0.24). Green and red OLEDs fabricated with 2 and 3 , respectively, also give high quantum efficiencies (～ 6.7 %), with CIE coordinates of (0.31, 0.63) and (0.59, 0.46), respectively. The current‐density–voltage characteristics of devices made using dopants 2 and 3 indicate that hole trapping is enhanced by short Pt–Pt distances (< 3.1 Å). Blue electrophosphorescence is achieved by taking advantage of the binuclear molecular geometry in order to suppress dopant intermolecular interactions. No evidence of low‐energy emission from aggregate states is observed in OLEDs made with 50 % 1 doped into mCP. OLEDs made using 100 % 1 as an emissive layer display red luminescence, which is believed to originate from distorted complexes with compressed Pt–Pt separations located in defect sites within the neat film. White OLEDs are fabricated using 1 and 3 in three different device architectures, either with one or two dopants in dual emissive layers or both dopants in a single emissive layer. All the white OLEDs have high quantum efficiency (～ 5 %) and brightness (～ 600 Cd m^–2 at 10 V).     

Comparison of total and faecal coliforms as faecal indicator in eutrophicated surface water.

The aim of this study was to evaluate the use of total coliforms (TC) and faecal coliforms (FC) using a membrane filtration method for precise monitoring of faecal pollution in Korean surface water. The samples were collected in Korea from both main rivers and their tributaries. Presumptive TC * FC were enumerated. The ratios of presumptive FC to TC were not constant, but varied widely, and TC were difficult to enumerate because of overgrowth by background colonies. For FC this was not the case. Seven hundred and three purified strains of presumptive TC * FC and their background colonies were biotyped using API 20E. Among 272 presumptive TC, non-faecal related species, Aeromonas hydrophila dominated (34.6%) and E. coli accounted for only 5.1%. In contrast, E. coli made up 89% of the 209 presumptive FC. Furthermore, of 164 background colonies on Endo Agar LES, 54.9% was A. hydrophila, while background colonies on m-FC Agar were few (58 strains), and despite their atypical colony appearance, most of them were biotyped as enteric bacteria. These results reveal that the detection of FC rather than TC using m-FC Agar is more appropriate for faecal pollution monitoring in eutrophicated surface water located in a temperate region.     

Recovery of gold cyanide using inherently conducting polymers

Removal of gold from basic solutions containing [Au(CN)₂]^? has been demonstrated using the inherently conducting polymer polypyrrole. Polymers containing sulfonated aromatic dopants have been found to display a significant ability to remove gold from such solutions. Experiments performed in solutions containing both gold and copper cyanide complexes indicate that the recovery process is not highly selective. However, the polypyrroles used display significantly faster rates of gold recovery than activated carbon. © 2003 Society of Chemical Industry     

1/f noise in large-area Hg<Subscript>1−x</Subscript>Cd<Subscript>x</Subscript>Te photodiodes

The 1/f noise in photovoltaic (PV) molecular-beam epitaxy (MBE)-grown Hg_1−xCd_xTe double-layer planar heterostructure (DLPH) large-area detectors is a critical noise component with the potential to limit sensitivity of the cross-track infrared sounder (CrIS) instrument. Therefore, an understanding of the origins and mechanisms of noise currents in these PV detectors is of great importance. Excess low-frequency noise has been measured on a number of 1000-μm-diameter active-area detectors of varying “quality” (i.e., having a wide range of I-V characteristics at 78 K). The 1/f noise was measured as a function of cut-off wavelength under illuminated conditions. For short-wave infrared (SWIR) detectors at 98 K, minimal 1/f noise was measured when the total current was dominated by diffusion with white noise spectral density in the mid-10⁻¹⁵A/Hz^1/2 range. For SWIR detectors dominated by other than diffusion current, the ratio, α, of the noise current in unit bandwidth i_n(f = 1 Hz, V_d = −60 mV, and Δf = 1 Hz) to dark current I_d(V_d = −60 mV) was α_SW-d = i_n/I_d ∼ 1 × 10⁻³. The SWIR detectors measured at 0 mV under illuminated conditions had median α_SW-P = i_n/I_ph ∼ 7 × 10⁻⁶. For mid-wave infrared (MWIR) detectors, α_MW-d = i_n/I_d ∼ 2 × 10⁻⁴, due to tunneling current contributions to the 1/f noise. Measurements on forty-nine 1000-μm-diameter MWIR detectors under illuminated conditions at 98 K and −60 mV bias resulted in α_MW-P = i_n/I_ph = 4.16 ± 1.69 × 10⁻⁶. A significant point to note is that the photo-induced noise spectra are nearly identical at 0 mV and 100 mV reverse bias, with a noise-current-to-photocurrent ratio, α_MW-P, in the mid 10⁻⁶ range. For long-wave infrared (LWIR) detectors measured at 78 K, the ratio, α_LW-d = i_n/I_d ∼ 6 × 10⁻⁶, for the best performers. The majority of the LWIR detectors exhibited α_LW-d on the order of 2 × 10⁻⁵. The photo-induced 1/f noise had α_LW-P = i_n/I_ph ∼ 5 × 10⁻⁶. The value of the noise-current-to-dark-current ratio, α appears to increase with increasing bandgap. It is not clear if this is due to different current mechanisms impacting 1/f noise performance. Measurements on detectors of different bandgaps are needed at temperatures where diffusion current is the dominant current. Excess low-frequency noise measurements made as a function of detector reverse bias indicate 1/f noise may result primarily from the dominant current mechanism at each particular bias. The 1/f noise was not a direct function of the applied bias.     

Training and optimization of an artificial neural network controlling a hybrid power filter

A hybrid power compensator (HPC) consisting of a static VAr compensator and a dynamic compensator needs to be optimally controlled during the compensation of nonlinear loads. The HPC must be controlled to meet minimum requirements in terms of power factor and harmonic distortion, while at the same time minimizing its total cost. An artificial neural network (ANN) is used to control the HPC amidst a very dynamic power system environment. The performance of a reference ANN is evaluated while controlling an HPC connected to a typical nonlinear industrial load. The training and performance of the ANN is then optimized in terms of training set size, training set packing and ANN topology and the performance compared to the reference ANN. This paper highlights the importance of optimising the mentioned ANN parameters to achieve optimum ANN training and modeling accuracy. The results obtained reveals that the application of an ANN in controlling an HPC is feasible given that the ANN parameters are chosen appropriately.     

Recension des écrits sur l'impact des contacts sexuels précoces sur les hommes.

A review of the literature on the impact of sexual contacts between adults and boys reveals the existence of two principal outcomes: 1) some participants develop various disorders once in adulthood, such as behavioural problems, sexual disorders, or personality problems; 2) some participants do not present with any major disorders in the long run. These different outcomes may be associated with several moderating variables related to the sexual contacts, such as the level of coercion at the time of these contacts, the bond between the child and the adult, or the context of the sexual relation. However, the conclusions relating to the relations between early sexual contacts with adults and subsequent problems of adaptation in adulthood are difficult to determine. This is because of various methodological problems associated with relevant studies (i.e., definition of these contacts, nature of the sample, method evaluation, statistical analyses). In this article, we propose certain avenues of research that may help clarify this problem. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Characteristic Features of the Optimal Processing of the Results of Measurements in the Case of a Random Observation Function

An analysis is made of the characteristic features and problems of the optimal processing of the results of measurements in the case of a random observation function utilizing a nonlinear Kalman filter. A method is proposed for increasing the convergence domain of the filter with additional processing of measurements in the frequency domain.     

Influence of device engineering on the analog and RF performances of SOI MOSFETs

This work presents a systematic comparative study of the influence of various process options on the analog and RF properties of fully depleted (FD) silicon-on-insulator (SOI), partially depleted (PD) SOI, and bulk MOSFET's with gate lengths down to 0.08 /spl mu/m. We introduce the transconductance-over-drain current ratio and Early voltage as key figures of merits for the analog MOS performance and the gain and the transition and maximum frequencies for RF performances and link them to device engineering. Specifically, we investigate the effects of HALO implantation in FD, PD, and bulk devices, of film thickness in FD, of substrate doping in SOI, and of nonstandard channel engineering (i.e., asymmetric Graded-channel MOSFETs and gate-body contacted DTMOS).     

Inside Front Cover: The Elastic Properties and Plastic Behavior of Two‐Dimensional Polymer Structures Fabricated by Laser Interference Lithography (Adv. Funct. Mater. 10/2006)

The probing of the micromechanical properties within a two‐dimensional polymer structure with sixfold symmetry fabricated via interference lithography reveals a nonuniform spatial distribution in the elastic modulus “imprinted” with an interference pattern in work reported by Tsukruk, Thomas, and co‐workers on p. 1324. The image prepared by M. Lemieux and T. Gorishnyy shows how the interference pattern is formed by three laser beams and is transferred to the solid polymer structure. The elastic and plastic properties within a two‐dimensional polymer (SU8) structure with sixfold symmetry fabricated via interference lithography are presented. There is a nonuniform spatial distribution in the elastic modulus, with a higher elastic modulus obtained for nodes (brightest regions in the laser interference pattern) and a lower elastic modulus for beams (darkest regions in the laser interference pattern) of the photopatterned films. We suggest that such a nonuniformity and unusual plastic behavior are related to the variable material properties “imprinted” by the interference pattern.