1/f noise in large-area Hg<Subscript>1−x</Subscript>Cd<Subscript>x</Subscript>Te photodiodes

The 1/f noise in photovoltaic (PV) molecular-beam epitaxy (MBE)-grown Hg_1−xCd_xTe double-layer planar heterostructure (DLPH) large-area detectors is a critical noise component with the potential to limit sensitivity of the cross-track infrared sounder (CrIS) instrument. Therefore, an understanding of the origins and mechanisms of noise currents in these PV detectors is of great importance. Excess low-frequency noise has been measured on a number of 1000-μm-diameter active-area detectors of varying “quality” (i.e., having a wide range of I-V characteristics at 78 K). The 1/f noise was measured as a function of cut-off wavelength under illuminated conditions. For short-wave infrared (SWIR) detectors at 98 K, minimal 1/f noise was measured when the total current was dominated by diffusion with white noise spectral density in the mid-10⁻¹⁵A/Hz^1/2 range. For SWIR detectors dominated by other than diffusion current, the ratio, α, of the noise current in unit bandwidth i_n(f = 1 Hz, V_d = −60 mV, and Δf = 1 Hz) to dark current I_d(V_d = −60 mV) was α_SW-d = i_n/I_d ∼ 1 × 10⁻³. The SWIR detectors measured at 0 mV under illuminated conditions had median α_SW-P = i_n/I_ph ∼ 7 × 10⁻⁶. For mid-wave infrared (MWIR) detectors, α_MW-d = i_n/I_d ∼ 2 × 10⁻⁴, due to tunneling current contributions to the 1/f noise. Measurements on forty-nine 1000-μm-diameter MWIR detectors under illuminated conditions at 98 K and −60 mV bias resulted in α_MW-P = i_n/I_ph = 4.16 ± 1.69 × 10⁻⁶. A significant point to note is that the photo-induced noise spectra are nearly identical at 0 mV and 100 mV reverse bias, with a noise-current-to-photocurrent ratio, α_MW-P, in the mid 10⁻⁶ range. For long-wave infrared (LWIR) detectors measured at 78 K, the ratio, α_LW-d = i_n/I_d ∼ 6 × 10⁻⁶, for the best performers. The majority of the LWIR detectors exhibited α_LW-d on the order of 2 × 10⁻⁵. The photo-induced 1/f noise had α_LW-P = i_n/I_ph ∼ 5 × 10⁻⁶. The value of the noise-current-to-dark-current ratio, α appears to increase with increasing bandgap. It is not clear if this is due to different current mechanisms impacting 1/f noise performance. Measurements on detectors of different bandgaps are needed at temperatures where diffusion current is the dominant current. Excess low-frequency noise measurements made as a function of detector reverse bias indicate 1/f noise may result primarily from the dominant current mechanism at each particular bias. The 1/f noise was not a direct function of the applied bias.     

Effect of the Distribution of Manganese Ions on the Properties of Mn-Doped (Ba,Y)TiO3 PTCR Ceramics

The electrical properties and microstructure of (Ba,Y)TiO₃ PTCR ceramics were studied. The results indicate that the Mn ions increase the intergranular barrier height and produce a high-resistance layer on the grain surface. The temperature-dependent resistances of the grain bulk, surface layer, and grain boundaries, the temperature coefficient of resistance, and the magnitude of the varistor effect were assessed as a function of Mn content.     

Characteristic Features of the Optimal Processing of the Results of Measurements in the Case of a Random Observation Function

An analysis is made of the characteristic features and problems of the optimal processing of the results of measurements in the case of a random observation function utilizing a nonlinear Kalman filter. A method is proposed for increasing the convergence domain of the filter with additional processing of measurements in the frequency domain.     

Influence of device engineering on the analog and RF performances of SOI MOSFETs

This work presents a systematic comparative study of the influence of various process options on the analog and RF properties of fully depleted (FD) silicon-on-insulator (SOI), partially depleted (PD) SOI, and bulk MOSFET's with gate lengths down to 0.08 /spl mu/m. We introduce the transconductance-over-drain current ratio and Early voltage as key figures of merits for the analog MOS performance and the gain and the transition and maximum frequencies for RF performances and link them to device engineering. Specifically, we investigate the effects of HALO implantation in FD, PD, and bulk devices, of film thickness in FD, of substrate doping in SOI, and of nonstandard channel engineering (i.e., asymmetric Graded-channel MOSFETs and gate-body contacted DTMOS).     

Static energy reduction techniques for microprocessor caches

Microprocessor performance has been improved by increasing the capacity of on-chip caches. However, the performance gain comes at the price of static energy consumption due to subthreshold leakage current in cache memory arrays. This paper compares three techniques for reducing static energy consumption in on-chip level-1 and level-2 caches. One technique employs low-leakage transistors in the memory cell. Another technique, power supply switching, can be used to turn off memory cells and discard their contents. A third alternative is dynamic threshold modulation, which places memory cells in a standby state that preserves cell contents. In our experiments, we explore the energy and performance tradeoffs of these techniques. We also investigate the sensitivity of microprocessor performance and energy consumption to additional cache latency caused by leakage-reduction techniques.     

Inside Front Cover: The Elastic Properties and Plastic Behavior of Two‐Dimensional Polymer Structures Fabricated by Laser Interference Lithography (Adv. Funct. Mater. 10/2006)

The probing of the micromechanical properties within a two‐dimensional polymer structure with sixfold symmetry fabricated via interference lithography reveals a nonuniform spatial distribution in the elastic modulus “imprinted” with an interference pattern in work reported by Tsukruk, Thomas, and co‐workers on p. 1324. The image prepared by M. Lemieux and T. Gorishnyy shows how the interference pattern is formed by three laser beams and is transferred to the solid polymer structure. The elastic and plastic properties within a two‐dimensional polymer (SU8) structure with sixfold symmetry fabricated via interference lithography are presented. There is a nonuniform spatial distribution in the elastic modulus, with a higher elastic modulus obtained for nodes (brightest regions in the laser interference pattern) and a lower elastic modulus for beams (darkest regions in the laser interference pattern) of the photopatterned films. We suggest that such a nonuniformity and unusual plastic behavior are related to the variable material properties “imprinted” by the interference pattern.     

Simulating strength and failure in engineering plant

Current features are considered in the calculation of carrying capacities for constructions in engineering plant (EP). Methods and algorithms are described for EP calculations with comprehensive incorporation of the effects from technological and working defects on the behavior of structures under standard and emergency conditions. __________ Translated from Khimicheskoe i Neftegazovoe Mashinostroenie, No. 8, pp. 38–40, August, 2006.     

Spinel Phase Relations in the Fe3O4–CuFe2O4 System

Phase equilibria involving spinel solid solutions, delafossite, and hematite in the Fe–Cu–O system are studied by emf measurements in solid-electrolyte galvanic cells. The results demonstrate that, above 1250 K, Fe₃O₄ and CuFe₂O₄ form a continuous series of solid solutions. At lower temperatures, the solid solution disproportionates with the formation of delafossite and Fe₂O₃, and two spinel solid solutions appear: one based on Fe₃O₄ and the other based on Cu₂FeO₄. The compositions of the spinel phases in equilibrium with delafossite and Fe₂O₃ are determined in the range 1100–1250 K.     

Motive Force in a Complex Model of Mass Transfer

Relations for determining a motive force in a complex model of mass transfer as applied to concurrent, countercurrent, and cross motion of the vapor and liquid phases have been introduced. These forces have been compared for different forms of organization of the flow, and their comparison with similar quantities from the known Murphree and Hausen models is presented.