Ischemia‐reperfusion injury. A phenomenon,that also occurs in the bone

Ischemia‐reperfusion injury of the bone occurs due to traumatic and non‐traumatic alterations affecting blood supply to the bone. It is likely to occur also upon insertion of an implant. Ischemia‐reperfusion injury of the bone has been studied by interruption of blood supply in situ, in limb replantation/transplantation models, in revascularized bone grafts and non‐vascularized bone fragments, as well as in isolated cultured cells. All cells of the bone are affected, including osteoblasts, osteocytes, osteoclasts, chondrocytes, and bone marrow cells. Critical ischemia times for induction of bone cell death, either in the ischemic period or following reperfusion, are in the range of 3 to 7 h. These critical ischemia times are significantly increased by decreasing the temperature from 37 °C to 0–4 °C. Anoxia is the most likely trigger of cell injury in the ischemic phase. In the reperfusion phase, reactive oxygen species are decisively involved in the injurious process. In general, however, the available information on the mechanism of ischemia‐reperfusion injury of the bone is relatively sparse. On the other hand, there are clear similarities to the mechanisms of ischemia‐reperfusion injury known from other organs, and there is a clear potential for protection against ischemia‐reperfusion injury of the bone.     

Flood risk mapping at European scale.

The aim of this article is to illustrate a framework for flood risk mapping at pan-European scale produced by the Weather-Driven Natural Hazards (WDNH) action of the EC-JRC-IES. Early results are presented in the form of flood risk index maps. We assess several flood risk factors that contribute to the occurrence of flood disasters. Among the causal factors of a flood disaster one is triggering a natural event in the form of extreme precipitation and consequently extreme river discharge and extreme flood water levels. The threatening natural event represents the hazard component in our assessment. Furthermore exposure and vulnerability are anthropogenic factors that contribute also to flood risk. In the proposed approach, flood risk is considered on the light of exposure, vulnerability and hazard. We use a methodology with a marked territorial approach for the assessment of the flood risk. Hence, based on mathematical calculations, risk is the product of hazard, exposure and vulnerability. Improvements on datasets availability and spatial scale are foreseen in the next phases of this study. This study is also a contribution to the discussion about the need for communication tools between the natural hazard scientific community and the political and decision making players in this field.     

Longitudinal analysis of semiconductor lasers with low reflectivity facets

An analysis is made of longitudinal effects in semiconductor lasers with low facet reflectivities. For this purpose, a self-consistent model is used based on the beam propagation method, which takes into account both the lateral and longitudinal dimension. The calculations show that longitudinal effects have a significant influence on the output fields in the laser.     

Adjuvant arthritis: influence of the adjuvant volume and composition on the non-specific inflammation

Adjuvant-induced arthritis is an animal model of chronic inflammatory disease widely used in anti-inflammatory and immunosuppressive drugs testing. When the development and the inhibition of the induced arthritis are measured by the injected paw oedema, it is difficult to delineate the immunological contribution from the persistent non-specific primary section. To study the influence of volume and composition of the injected adjuvant upon the primary non-specific inflammation, we devised a 3X4 factorial experiment on a strain of inbred rats with a low susceptibility to adjuvant-induced arthritis. The injection of mineral oil alone produces a persistent oedema. The injection of mycobacteriae in suspension in saline induces a rapid inflammatory response followed by a fast decrease of the oedema. When complete adjuvant is used, there is always a very strong interaction between the effects of the two components of the adjuvant, i.e. the measured oedemas are much greater than the calculated values, For a given injected volume, the inflammation is maximum when the concentration of mycobacteriae is 2.5 mg/ml. All the rats injected with complete adjuvant present a transient oedema of the non-injected hind paw. This oedema is very small and proportional to the amount of mycobacteria injected.     

On the hot-carrier-induced post-stress interface trap generation inn-channel MOS transistors

A continued fast interface trap generation is observed in n-channel MOS transistors after termination of the hot-carrier stress. The magnitude of this post-stress effect is strongly dependent on the conditions of the preceding stress, on the post-stress conditions and on the process parameters. For measurements at 293 K, a simple model is proposed which is based on the release of hydrogen by the thermal detrapping of holes, and which can explain the observed dependencies. The importance of the post-stress D_it-generation is illustrated for the case of dynamic stress conditions where it can lead to an apparently deviating degradation behavior     

Impurity Distribution Behavior in Caprolactam Extraction with Environmentally Benign Mixed Solvents

In a previous study a solvent mixture of heptane containing 40 mass % heptanol was selected as an alternative in the industrial extraction of caprolactam to replace benzene, toluene, or chlorinated hydrocarbons. This work reports the equilibrium distribution ratio of caprolactam and four model impurities of organic nature, namely, cyclohexanone, aniline, n‐methylcaprolactam, and cyclohexane‐carboxamide, comparing the mixed solvents with toluene as a reference. The resulting phase equilibria were interpreted using the equilibrium stage model. Based on these calculations it was found that, compared to toluene, the co‐extracted fraction of cyclohexanone and aniline was higher, that of n‐methylcaprolactam was comparable, and that of cyclohexane‐carboxamide was lower using the mixed solvent. Overall, the mixed solvent reduced the fraction of co‐extracted impurities by almost 10 %.     

Screening of supports for the immobilization of pectinmethylesterase from acerola (Malpighia glabra L)

A partially purified extract of pectinmethylesterase (PME) from acerola fruit was immobilized on various supports: glass, celite, chrysotile, agarose, concanavalin A Sepharose 4B, egg shell, polyacrylamide and gelatin. In addition, reticulation with glutaraldehyde was assessed, as well as the use of gelatin in the presence of celite, glass and silica. The highest immobilization yields were obtained when the pectinmethylesterase was immobilized in concanavalin A Sepharose 4B (81.7%) and in gelatin‐water (78.0%). Copyright © 2004 Society of Chemical Industry     

High-performance surface-micromachined inchworm actuator

This work demonstrates a polycrystalline silicon surface-micromachined inchworm actuator that exhibits high-performance characteristics such as large force (/spl plusmn/0.5 millinewtons), large velocity range (0 to /spl plusmn/4.4 mm/sec), large displacement range (/spl plusmn/100 microns), small step size (/spl plusmn/10, /spl plusmn/40 or /spl plusmn/100 nanometers), low power consumption (nanojoules per cycle), continuous bidirectional operation and relatively small area (600 /spl times/ 200/spl mu/m/sup 2/). An in situ load spring calibrated on a logarithmic scale from micronewtons to millinewtons, optical microscopy and Michelson interferometry are used to characterize its performance. The actuator consists of a force-amplifying plate that spans two voltage-controlled clamps, and walking is achieved by appropriately sequencing signals to these three components. In the clamps, normal force is borne by equipotential rubbing counterfaces, enabling friction to be measured against load. Using different monolayer coatings, we show that the static coefficient of friction can be changed from 0.14 to 1.04, and that it is load-independent over a broad range. We further find that the static coefficient of friction does not accurately predict the force generated by the actuator and attribute this to nanometer-scale presliding tangential deflections.