Improved HF modem using convolutional coding

The paper describes the design of a digitally implemented modem for use over HF (2-30 MHz) radio channels. As a completely digital approach offers the prospect of a number of significant improvements, a new digital multifrequency-shift-keying (MFSK) modem has been developed that employs a novel digital processing procedure termed code-assisted bit synchronisation (CABS). Signal detection is achieved via a set of noncoherent correlators, whilst symbol synchronisation and error correction are performed using a soft-decision Viterbi decoder. Practical tests of modem show that it operates effectively under both additive white Gaussian noise and real HF channel conditions     

Effect of magnesium content on the ageing behaviour of water-chilled Al-Si-Cu-Mg-Fe-Mn (380) alloy castings

A study of the effect of magnesium concentration on the ageing behaviour as measured by the hardness of 380 alloy was conducted for three levels of magnesium, namely 0.06 (base alloy), 0.33 and 0.5 wt%, for water-chilled castings (dendrite arm spacing ∼ 10–15 μm). Differential scanning calorimetry analysis of as-cast samples was carried out to determine the changes in the reactions of the phases obtained during alloy solidification, employing heating rates of 0.1 and 1.0°Cs⁻¹, up to approximately 700°C. Two heat treatments were applied to the as-cast alloys: T5 comprising ageing at 25 (room temperature), 155, 180, 200 and 220°C, for times up to 200 h, and T6 comprising solution heat treatment at 480 °C or 515°C for 8 h, followed by quenching in warm water at 60°C, followed by immediate artificial ageing at 155 or 180°C for varying times up to 100h. The results show that the higher hardness values obtained with T6 treatment can be explained by the excess precipitation of magnesium-containing phases in the as-solidified alloys. This precipitation could be eliminated under the high cooling-rate conditions prevalent in die-casting operations so that T5 treatment may be used to replace T6 treatment to produce the same hardness values. In addition, solution heat treatment in the low-temperature range (480–515°C) is adequate to produce the required changes in silicon morphology and dissolution of magnesium in the matrix. No significant difference in hardness behaviour was observed when the magnesium content was increased beyond 0.3 wt%.     

The visual control of reaching and grasping: Binocular disparity and motion parallax.

The primary visual sources of depth and size information are binocular cues and motion parallax. Here, the authors determine the efficacy of these cues to control prehension by presenting them in isolation from other visual cues. When only binocular cues were available, reaches showed normal scaling of the transport and grasp components with object distance and size. However, when only motion parallax was available, only the transpont component scaled reliably. No additional increase in scaling was found when both cues were available simultaneously. Therefore, although equivalent information is available from binocular and motion parallax information, the latter may be of relatively limited use for the control of the grasp. Binocular disparity appears selectively important for the control of the grasp. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

The Quantization Property of Probability Distributions of the Characteristics of Dynamic Systems Observed in the Presence of Random Disturbances

The class of linear stochastic dynamic systems is defined, such that the laws of the probability distribution of values of output signals of a system are determined by its equations complying with the case of the absence of random disturbances. These distribution laws are found to be similar to the quantum laws of the distribution values of observable physical quantities. On this basis, a possibility of the definition of the quantum systems as systems of this class is investigated. It is shown that the theoretical proof of some axioms of quantum mechanics and new facts requiring the experimental verification follow from this definition.     

On the leverage of high-fT transistors foradvanced high-speed bipolar circuits

A detailed study on the leverage of high-f_T transistors for advanced high-speed bipolar circuit applications is presented. It is shown that for the standard ECL (emitter-coupled logic) circuit, the leverage of high f_T is limited by the passive resistors (emitter-follower resistor and collector load resistor) and wire delay, especially in the low-power regime. For the standard NTL (nonthreshold logic) circuit, the leverage is higher due to its front-end configuration and lower power supply value. As the passive resistors are decoupled from the delay path in various advanced circuits utilizing active-pull-down schemes, the leverage of high F_T becomes more significant     

隧道受震破壞調查分析與修復管理案例

就隧道震後之災損模式進行統計與災損原因研判,並利用數值分析方法研判安全性,就結構加固等改善措施之設計考量作詳細說明;另由於隧道結構物的損壞範圍大,且修復經費受限,必須藉由定期檢测進行長期維護管理,以防範意外發生。於此,利用Vidco-GIS自動化影像地理资訊系統之e化新技術,以動態及靜態影像紀錄隧道災損狀況,同時亦整合建置前期設計、施工圖及定期維護等資料,相關成果以資料庫方式纳入日常維護管理,以有限人力有效率地進行維護管理紀錄並随時掌握現況供作決策之明確參考。     

0.5-μm 3.3-V BiCMOS standard cells with 32-kilobyte cache andten-port register file

BiCMOS standard cell macros, including a 0.5-W 3-ns register file, a 0.6-W 5-ns 32-kbyte cache, a 0.2-W 3-ns table look-aside buffer (TLB), and a 0.1-W 3-ns adder, are designed with a 0.5-μm BiCMOS technology. A supply voltage of 3.3 V is used to achieve low power consumption. Several BiCMOS/CMOS circuits, such as a self-aligned threshold inverter (SATI) sense amplifier and an ECL HIT logic are used to realize high-speed operation at the low supply voltage. The performance of the BiCMOS macros is verified using a fabricated test chip