A compact fiber-optic magnetometer employing an amorphous metalwire transducer

A compact fiber-optic magnetometer constructed using a short piece of amorphous metal wire (5-cm long×100-μm diameter) as the magnetostrictive transducer is discussed. The inherently large ratio of length to cross-sectional area results in a low demagnetization along the axial direction. A magnetostrictive constant of 5×10^-5 /Oe², which is 10-50 times larger than the reported values for transducers made from Metglas ribbons, was measured. Minimum detectable magnetic fields on the order of 10^-5 Oe/Hz^1/2 at 1 Hz were achieved using a 5-cm-long sensing fiber     

Fire and explosion hazards in the spray drying of milk

Recent reports in the literature indicate that incidents involving fires and explosions in the spray drying of milk products are increasing in number. Whilst milk powder is not highly explosible, the conditions for a dust explosion, apart from the ignition source are almost always present in certain areas of a spray dryer during its normal operation. Self-ignition of deposits is known to be possible at the high temperatures in a spray dryer. At best, this can cause product degradation and discolouration whilst at worst it can provide the source of ignition for an explosion. This paper is an attempt to draw together recent work on fire and explosion prevention and protection formilk powders.     

Process Variables, Gelatinized Starch and Moisture Effects on Physical Properties of Mungbean Noodles

The effects of amounts of gelatinized starch and moisture in the final slurry or dough, cooking time, holding time, and holding temperature on physical properties of mungbean noodles were studied. Cooking loss, cutting stress, work to cut, and transparency of noodles were measured. Moisture content of the final slurry or dough, cooking time, and holding temperature were the most important factors that affected physical properties of mungbean noodles. Processing should be done at moisture contents not exceeding 55%, cooking times not longer than 40 set, and holding temperatures not lower than 3° using 5% of total starch as gelatinized starch and holding time of 36 hr.     

Bacteriological Safety of Swine Carcasses Treated with Reconditioned Water

Swine carcass microflora were evaluated for selected foodborne pathogens after exposure to reconditioned water during scalding, dehairing, and polishing operations. Reused water had been reconditioned and chlorinated. Rodac plates applied to hams were used to assess carcass microflora. Water samples were enumerated using membrane filtration or spiral plating. Sampling was at mid-week throughout the year. Total aerobic plate counts on hams were unaffected by treating with potable or reconditioned waters. No differences were observed for staphylococci, enterics, fecal streptococci, Listeria monocytogenes, coliforms, and Aeromonas levels. A preevisceration potable water carcass wash reduced the bacterial load, regardless of initial treatment. Bacterial counts on carcasses paralleled those in water. Reuse is an alternative to potable water for initial slaughter operations without diminishing bacteriologic safety.     

Aflatoxin B1 contamination of shrimp feeds and its effect on growth and hepatopancreas of pre-adult Penaeus monodon

A survey of aflatoxin B₁ (AFLB₁) levels in commonly used commercial shrimp finisher feeds in the Philippines showed a various range of values from not detected to 120 μg kg^?1 using high-performance thin-layer chromatography. Six experimental diets were prepared to contain various levels of AFLB₁ based on survey results to determine the effects of such contamination in pre-adult shrimp Penaeus monodon (17.5 ± 0.6 g). Results showed that shrimps fed diets containing AFLB₁ greater than or equal to 73.8 μg kg^?1 gave comparatively poor growth rate and higher susceptibility to shell diseases. No AFLB₁ residues were detected in sampled whole shrimp tissues after 62 days of exposure to AFLB₁ containing diets indicating a low potential for transmission of the toxin from edible shrimp tissues to consumers. Histopathological alterations in the hepatopancreas of shrimp chronically exposed to AFLB, were observed in all samples. The degree of alterations correlated with the level of AFLB₁. Based on growth performance, pre-adult shrimps can tolerate AFLB₁ levels of up to 52.3 μg kg^?1 in the feeds although histopathological changes were already evident in the tissues of shrimps given diets with 26.5 μg kg^?1 AFLB₁.     

High speed BiCMOS current mode differential track-and-hold circuit

A new principle for a high speed BiCMOS differential track-and-hold circuit based on current mode processing is presented, and simulation results are given. The main characteristics are an acquisition time of 5.5 ns for 8 bit precision and a small-signal bandwidth of 1 GHz     

Spectral domain analysis of conductor losses in a multiconductorsystem via the incremental inductance rule

Spectral domain analysis is adapted to analyse the conductor losses of a multiconductor system embedded in a multilayered medium using a quasi-TEM approach and assuming a strong skin effect. After adapting the incremental rule to a multiconductor system, the conductor losses are computed in terms of the derivative of the inductance matrix     

Continuous-wave laser action in Er3+:YLF at 3.41 μm

Continuous-wave laser emission at 3.41 μm from an erbium-doped LiYF₄ crystal (Er³⁺:YLF) at 77 K is demonstrated. Operation of this four-level laser is based on the Er^{3+ 4}F_9/2-⁴I_9/2 transition. An output power of 12 mW and a slope efficiency of 2% have been achieved     

Post-deposition treatment effects on hydroxyapatite vacuum plasma spray coatings

The purpose of this work is to evaluate the effects of post-deposition heat treatments on high and low crystallinity hydroxyapatite coatings on Ti6Al4V alloy. HA layers were produced by the vacuum plasma spray (VPS) technique, and the desired degrees of crystallinity were obtained by changing the deposition parameters. An analysis of the mechanical properties of the coatings and their adhesion to the substrate has been done by shear strength test. X-ray diffraction analysis was used to detect the structure and the chemical components in which HA dissociates during the deposition process and heat treatments. The data obtained indicates that heat treatments can increase the crystallinity of HA, but they also introduce a mechanical degradation of the coatings. After heat treatments, it was also observed that a large amount of tetracalcium phosphate was formed.     

FOCUS-type fuel assembly for PWRs

In recent years the development efforts for Siemens PWR fuel assemblies were mainly concentrated on reducing the fuel cycle costs and increasing the operational reliability of the fuel assemblies.The first objective was aimed at increasing the average discharge burnup to > 50 MWd/kgU and increasing the critical heat flux. The high envisaged burnup required to develop a corrosion resistant cladding tube outside the Zry-4 range. The decision was made to use a Duplex cladding tube consisting of a corrosion optimized outer layer on a Zry-4 base material. A ZrSnFeCr alloy with reduced tin content was chosen for the outer layer. The critical heat flux could be increased by introducing mixing vanes on the spacer grids within the active length.To reach the second objective, reliable avoidance of spacer grid damage during core loading and unloading and reduction of fuel rod defects by debris fretting, the spacer grid corners were improved and a debris separation grid was developed.These design improvements were introduced into the new FOCUS-type fuel assembly. The name FOCUS stands for “Fuel assembly with Optimized Cladding and Upgraded Structure”.