Investigation of solar selective and microstructural properties of molybdenum black immersion coatings on cobalt substrates

Molybdenum black solar selective coatings have been produced on cobalt by immersion in a solution of ammonium paramolybdate and nickel sulphate. The cobalt was electroplated on nickel-plated copper prior to immersion in the paramolybdate solution. The maximum solar absorptance of the resulting molybdenum black coating was about 0.91. The minimum emittance was about 0.1 for coatings on cobalt deposited with an addition agent and about 0.23 for coatings on cobalt deposited without addition agent in the 60 °C plating solution. These differences have been related to the coating morphology determined by scanning electron microscopy. The emittance of coatings on cobalt deposited without addition agent decreases (or remains unchanged) during short-term heat treatment while that of coatings deposited on cobalt plated with addition agent increases somewhat. Reduction of the cobalt plating bath temperature to 45 °C can also lead to good initial coating properties but without the requirement for an addition agent in the cobalt plating bath. XPS studies show that the oxidation state of molybdenum in the coatings is approximately + 5 corresponding to Mo₄O₁₁. This reduces to + 4 after argon ion bombardment. Some cobalt may be present in the coatings in the form of CoO.     

Mikrobielle Werkstoffzerstörung – Schadensfälle und Gegenmaßnahmen: Umweltrechtliche Belange

Microbial deterioration of materials – case histories and countermeasures: Legal aspects of environmental protection Biofouling is a natural process. Usually, it does not cause too much harm if taken care of properly. If biofouling is fought by special means, problems may arise. The waste water does not meet the due standards. Sometimes the recipe of the treatment agent is not known. If the treatment causes more problems than it can solve help is needed quickly. Yet, it is advisable to keep one's mind clear. Wrong help can become very expensive. In addition, legal punishment will follow, if environmental legislation is hurt. Damages of the environment will be payed by an insurance company only, if the risk is covered by the insurance contract in advance. The best way to be sure is to have a good lawyer, a good expert in environmental techniques and environmental legislation, a good insurance, and to anticipate possible risks.     

Asymmetric alumina membranes electrochemically formed in oxalic acid solution

Alumina membranes were fabricated by anodizing aluminium metal in 0.15 M oxalic acid. The growth kinetics of the porous layer were investigated in the temperature range –1 to 16 °C using linear potential scans up to 70 V. The faradaic efficiencies of metal oxidation and of porous layer formation, determined by applying Faraday's law, were found to be independent of both temperature and electrical charge. SEM analysis of the metal-side and solution-side surfaces revealed different morphologies. After dissolution of the barrier layer in phosphoric acid, the metal-side surface showed circular pores whose size of about 90 nm was found to be uniform and independent of temperature. The pore population was also practically independent of temperature and a value of about 4 × 10¹³ pores m^–2 was determined. On the solution-side surface the presence of a deposit partially occluding the mouths of pores was observed. This coating could be removed by chemical etching in NaOH or thermal treatment at 870 °C, where decomposition of oxalate occurs. This supports the hypothesis that the deposit consists of an aluminium salt containing oxalate anions precipitated from the solution. The results show that it is possible to control the morphological characteristics of the anodic alumina membranes by careful choice of experimental conditions.     

Cure reaction for modified diallylbisphenol A/diaminodiphenylsulfone/bismaleimide

The glass‐transition temperature as a function of curing conversion for a modified diallylbisphenol A/diaminodiphenylsulfone/bismaleimide (BMI) resin was investigated at different temperature regimes and modeled using a modified Di Benedetto equation. Although the relationship between the glass‐transition temperature and conversion of the BMI system conforms to the Di Benedetto equation for α < 0.6 and at lower cure temperatures, at higher cure temperatures the results deviated significantly from the equation; thus, it was an inadequate model for the system. Fourier transform IR analysis showed that the major crosslinking reactions did not occur during cure for the modified BMI at and below 150°C. However, as the cure temperature was increased, the crosslinking reactions responsible for 3‐dimensional network structures became more dominant. At 190°C the C? N? C_stretch vibration of the uncured maleimide ring converted into succinimide rings in the curing process. Simultaneously, a decrease was observed for the absorbance bands of ? C? H_bending (maleimide). The higher cure temperatures induced a significantly faster initial crosslinking rate and also resulted in a shorter period of time after which further crosslinking was retarded, because the increase in the crosslinks also physically slowed further crosslinking activity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 227–235, 2002     

Influence of ethylene‐co‐vinyl acetate copolymers on the flow properties of wax synthetic systems

Wax crystallization can cause serious damage to petroleum flow because as the viscosity increases, there is organic deposition in the pipe lines, which causes oil production reduction. Ethylene–vinyl acetate copolymers (EVA) are used as an alternative to prevent such problems. The influence of EVA copolymers on the properties of wax synthetic systems, composed of a solvent mixture and paraffin and petroleum asphalt residue (PAR), was evaluated in this work. The performance of EVA as a wax inhibitor depends on the molecular weight and vinyl acetate content of the copolymer and on the presence of the asphalt fraction. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1337–1348, 2002     

Control of circulating current in two parallel three-phase boost rectifiers

One unique feature in parallel three-phase converters is a potential zero-sequence circulating current. To avoid the circulating current, most present technology uses an isolation approach, such as transformers or separate power supplies. This paper proposes a parallel system where individual converters connect both AC and DC sides directly without additional passive components to reduce size and cost of the overall parallel system. In this case, the control of the circulating current becomes an important objective in the converter design. This paper: (1) develops an averaged model of the parallel converters based on a phase-leg averaging technique; (2) a zero-sequence model is then developed to predict the dynamics of the zero-sequence current; (3) based on the zero-sequence model, this paper introduces a new control variable, which is associated with space-vector modulation; (4) a strong zero-sequence current control loop is designed to suppress the circulating current; and (5) simulation and experimental results validate the developed model and the proposed control scheme.     

Statistical characterization of urban spatial radio channels

We present a statistical analysis of wideband three-dimensional channel measurements at base station locations in an urban environment. Plots of the received energy over azimuth, elevation, and delay planes suggest that the incident waves group to clusters in most measured transmitter positions. A super-resolution algorithm (Unitary ESPRIT) allows one to resolve individual multipath components in such clusters and hence enables a detailed statistical analysis of the propagation properties. The origins of clusters-sometimes even individual multipath components-such as street apertures, large buildings, roof edges, or building corners can be localized on the city map. Street guided propagation dominates most of the scenarios (78%-97% of the total received power), while quasi-line-of-sight over-the-rooftop components are weak(3%-13% of the total received power). For this measurement campaign, in 90% of the cases, 75% of the total received power is concentrated in the two strongest clusters, but only 55% in the strongest one. Our analysis yields an exponential decay of power with 8.9 dB/μs, and a standard deviation of the log-normally distributed deviations from the exponential of 9.0 dB. The power of cross-polarized components is 8 dB below copolarized ones on average (vertical transmission)     

Multiple access for UWB impulse radio with pseudochaotic time hopping

Pseudochaotic time hopping (PCTH) is a previously proposed encoding/modulation scheme for ultra-wideband (UWB) impulse radio. PCTH exploits concepts from symbolic dynamics to generate aperiodic spreading sequences, resulting in a noise-like spectrum. We present a multiple-access technique suitable for the PCTH scheme. In particular, we provide an analytical expression of the bit-error rate performance as a function of the number of users and validate it by simulation.     

A quantum amplifier model for predicting temporal variations in theoutput power from a semiconductor laser on a picosecond time scale

A new model for simulating temporal fluctuations in the power emitted by a semiconductor laser is described. Light in the cavity is assumed to circulate in the form of traveling photon packets, in which the photon number fluctuates due to the processes of spontaneous emission, stimulated emission, absorption, scattering, and reflection. The dipole dephasing time T plays a critical role in modeling the interaction of the photon packets and gain medium. The Monte Carlo method is used to simulate the temporal behavior of a continuously pumped Fabry-Perot laser. The laser output power is found to exhibit periodic fluctuations at the cavity transit time frequency (longitudinal mode beat frequency). The amplitude of these fluctuations, as well as the relaxation oscillation, which occurs at a much lower frequency, is strongly influenced by the magnitude of T. The results of these simulations are related to the temporal behavior expected from a conventional FP laser     

Evolution of the capillary network in a reactive powder concrete during hydration process

Ultrasonic waves in echographic mode, combined with autogenous shrinkage measurements, were used to study the evolution of the capillary network of reactive powder concrete (RPC) from the time after the mixing. Two characteristic porous classes have been identified: the first, between 10 and 20 nm, begins when the material reaches its solid hyperstatic state, and the second about 1 or 2 nm. The first class is associated with the porous space between the C-S-H hydrate clusters and the second with the internal porosity of the hydrate. The evolution of the active capillary radius as a function of the degree of hydration allows us to understand the strong interaction between the capillary network size and the chemical activity given by the dissipated calorimetric power curve. Indeed, the maximum point of the chemical activity marks the transition of the first class of pores to the second one. Finally, measurements of electrical conductivity through RPC samples show that after the maximum of the dissipated power, the curve of this electrical conductivity presents the same evolution as the capillary radius. As the electrical conductivity clearly depends on the evolution of the capillary network, the similarity between the results confirms our analysis in pore classes.