Three ways to implement interfacial techniques: application tomeasurements of chromatic dispersion, birefringence, and nonlinearsusceptibilities

Depending on the spectal width of the source illuminating an interferometer, measurement procedures can utilize either the whole interferogram, or only the fringe envelope, or only the fringe quick oscillations. With an ultraband spectrum source, a simplified adaptation of the methods of Fourier transform spectroscopy yields the variations of the test-fiber propagation constant over the whole wavelength-interval of the source. Chromatic dispersion can then be computed from a single interferogram. With narrower spectrum sources, only the fringe envelopes are utilized and yield measurements of mode delay, with application to chromatic and polarization mode dispersion. In this case, however, interferograms at several wavelengths are necessary. With even narrower spectrum sources, the fringe quick oscillations provide measurements of phase shifts, related to changes in the mode propagation constant, when outside perturbations are applied to the test fiber. A direct method for measuring the third-order nonlinear susceptibilities is discussed. In this case the outside perturbation is an intense pump laser field     

Analytic approach to the computation of the temperature distribution in multilayer structures under heating by cw scanning laser radiation

By using integral transform methods, an approach is developed to the solution of a problem on the temprature distribution in multilayer structures heated by cw scanning laser radiation, with phase transitions in the layers taken into account.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 53, No. 6, pp. 1000–1010, December, 1987.     

A comparison between the axial flux and the radial flux structures for PM synchronous motors

The aim of this paper is the comparison of the axial flux (AF) structures versus the conventional radial flux (RF) structures for permanent-magnet synchronous motors. The comparison procedure is based on simple thermal considerations. Two motor typologies are chosen and compared in terms of delivered electromagnetic torque. The comparison is developed for different motor dimensions and the pole number influence is put into evidence. The paper reports the complete comparison procedure and the related results analysis. The obtained results show that, when the axial length is very short and the pole number is high, the AF motors can be an attractive alternative to the conventional RF solutions.     

Incremental transmission loss allocation under pool dispatch

Incremental transmission loss analysis has been used for decades, but recent interest in its application to loss allocation calls for new in-depth results. This paper demonstrates that, for incremental methods to be applied correctly in loss allocation, it is first necessary to specify the load distribution and loss supply strategies. Incremental loss allocation among bus power injections is shown to be arbitrary and, therefore, open to challenge as discriminatory. Loss allocation is possible among incremental loads and/or generators, but the proportion of the total losses assigned to either one is arbitrary. Unique, nonarbitrary incremental loss allocations are however possible among the "equivalent" incremental bilateral exchanges between generators and loads. From these basic components it is possible then to calculate the allocation among generators or loads in any specified proportion. The main results, although developed initially for small increments, are extended to large variations. Finally, a general incremental loss allocation algorithm is developed and tested     

Modern Aluminum and Magnesium Alloys and Composite Materials Based on Them

Aluminum and magnesium alloys are the base structural materials in aircraft and spacecraft engineering. The main stages of the development and introduction of light alloys are described.     

Influence of Edible Films upon the Moisture Loss and Microstructure of Dietetic Sucrose-Free Sponge Cakes during Storage

The kinetics of changes in the bound water content in dietetic sucrose-free sponge cakes (DC) during storage was investigated. The effect of edible films of polymyxan, pectin, xanthan, and carboxymethylcellulose upon this kinetics was also investigated. The quantitative changes in both states of water (slightly bound water and strongly bound water) were registered by combined dynamic analysis (thermogravimetry analysis, TGA, and differential thermal analysis, DTA). The moisture changes in DC crumb were analyzed by drying out to constant mass. The rate constants were determined according the equation q = q_oe^-kt. The values of rate constants 'k', in day^-1, concerning the different edible films were as follows: for crumb moisture is (8.00 ≤ k ≤ 12.47) × 10^-3, for bound water is (3.07 ≤ k_w ≤ 6.26) × 10^-2, for slightly bound water is (4.22 ≤ k₁ ≤ 8.49) × 10^-2 and for strongly bound water is (2.02 ≤ k₂ ≤ 5.62) × 10^-2 as compared to 18.53 × 10^-3, 7.16 × 10^-2, 9.04 × 10^-2, and 5.36 × 10^-2 in the uncovered DC, respectively. The best water-retaining effect in respect to crumb moisture during storage was ascertained in the use of polymyxan and xanthan films. The lowest rate constant values for bound water and its two states were measured for DC covered with pectin. The relation between the kinetics of both bound water states during storage and ageing of the crumb of DC covered with different edible films and the crumb microstructure was represented. By means of scanning electron microscope was read the smallest change in crumb microstructure of pectin-covered DC on the sixth day of storage.     

Crisis phenomena upon evaporation in grid capillary and porous coatings and arterial structures of heat pipes

The article presents the results of experimental investigations of critical (limit) heat fluxes upon evaporation on porous coatings, and it substantiates the physical model of the process.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 49, No. 4, pp. 607–614, October, 1985.     

Structure and composition of guanidine acrylate, guanidine methacrylate, their homopolymers, and copolymers with diallyldimethylammonium chloride

Structures and compositions of the monomers guanidine acrylate and guanidine methacrylate, their homopolymers, and copolymers with diallyldimethylammonium chloride enriched in acrylate comonomer units were determined. It was shown that ampholytic copolymers, owing to their ionic nature, contained comonomeric guanidine acrylate or methacrylate units and diallyldimethylammonium chloride units, as well as the acrylate comonomer with the diallyl counterion and polymeric acrylate and diallyl ion pairs. It follows from IR and ¹H NMR data that guanidine methacrylate has the same structure (with two hydrogen bonds) in the solid state and in solutions. Guanidine acrylate structures in the solid state and in dimethylsulfoxide are identical and analogous to guanidine methacrylate structure in this solvent. In water, the guanidine acrylate structure has another type of hydrogen bonding (with one hydrogen bond, where the proton is shifted toward the guanidine group). These features of hydrogen bonding of guanidine acrylate and guanidine methacrylate are also retained in their homopolymers and copolymers with diallyldimethylammonium chloride. It was shown that the thermal stability of the copolymers was higher than that of their homopolymers, confirming the formation of intramolecular ion pairs of oppositely charged units of ampholytic copolymers. Moreover, the thermal stability of guanidine methacrylate-diallyldimethylammonium chloride copolymers is higher than that of guanidine acrylate-diallyldimethylammonium chloride copolymers.     

On the nonuniformity of a capillary flow

It is established that the capillary rise of a liquid has an oscillatory character, in contrast to the commonly accepted opinion that a vertical capillary is filled at a monotonically varying velocity. The value of the tangential shear stress arising in an ascending liquid is evaluated for ethyl alcohol and distilled water.