Improvement of RCA transistor using RTA annealing after theformation of interfacial oxide

A polysilicon emitter RCA transistor (an ultra-thin interfacial oxide layer exists between polysilicon and silicon emitter) is presented which can operate at 77 K for the first time. An ultra-thin (1.5 nm) interfacial oxide layer is grown deliberately between polysilicon and silicon emitter using RCA oxidation and excellent device stability is obtained after rapid thermal annealing (RTA) treatment in nitrogen atmosphere. The RCA transistor exhibits good electrical performance at very low temperature for an emitter area of 3 × 8 μm². The maximum toggle frequency of a 1:2 static divider is 1.2 GHz and 732 MHz at 300 K and 77 K, respectively     

Thermodynamic modeling of native point defects and dopants of GaN semiconductors

A thermodynamic modeling of GaN was carried out to describe the thermodynamic behavior of native defects, dopants, and carriers (free electrons and holes) in GaN semiconductors. The compound energy model (CEM) was used. An unintentionally doped GaN was taken as an example. Oxygen was introduced into the model as the unintentionally doped impurity, according to the practical experimental phenomena. The energies of component compounds in the model were defined based on the results of the ab initio calculations and adjusted to fit experimental data. The thermodynamic properties of the defects and the oxygen doped were calculated to show the facility of the model.     

A network management architecture for robust packet routing in meshoptical access networks

We describe an architecture for an optical local area network (LAN) or metropolitan area network (MAN) access. The architecture allows for bandwidth sharing within a wavelength and is robust to both link and node failures. The architecture can be utilized with an arbitrary, link-redundant mesh network (node-redundancy is necessary only to handle all node failures), and assumes neither the use of a star topology nor the ability to embed such a topology within the physical mesh. Reservation of, bandwidth is performed in a centralized fashion at a (replicated) head end node, simplifying the implementation of complex sharing policies relative to implementation on a distributed set of routers. Unlike a router, however, the head end does not take any action on individual packets and, in particular, does not buffer packets. The architecture thus avoids the difficulties of processing packets in the optical domain while allowing for packetized shared access of wavelengths. We describe the route construction scheme and prove its ability to recover from single link and single node failures, outline a flexible medium access protocol and discuss the implications for implementing specific policies, and propose a simple implementation of the recovery protocol in terms of state machines for per-link devices     

机动武器系统的含间隙动力学研究--下篇:系统仿真

本文把中篇建立的间隙铰模型引入多体系统动力学分析中,得到了一种处理含间隙多体系统动力学问题的一般方法.应用这种方法对机动武器的发射过程进行了原理性的仿真,验证了前面建立的碰撞模型和间隙模型,并分析了间隙对导弹运动状态的影响.导弹发射过程具有变拓扑的特点,本文方法提供了一种处理这类问题的思路.     

Automatic conversion from lexical words to prosodic words for mandarin text-to-speech system

In real speech, not like lexical words (LWs), prosodic words (PWs) are basic rhythmic units. The naturalness of a Text-to-Speech (TTS) system is directly influenced by the segmentation of the PWs. Most of the PWs are the combination of several LWs. In this paper, three Lexical Combination Models are proposed to combine LWs into PWs, including a Directed Acyclic Graph Model, a Segmentation Model and a Markov Model (MM). To cope with the situation where some long LWs should be segmented into two or more PWs, a Lexical Split Model (LSM) is applied to the long LWs. Experimental results prove that relatively constant results with various training data can be obtained from a MM. The Transformation-Based Error Driven Learning (TBED) algorithm, for its high performance of individual property, is applied in combination with the MM to improve the precision of PW segmentation. Experiments show that among the three proposed models, the MM combined with TBED and LSM, leads to the best performance, in which a precision of 93.00% and a recall of 93.23% are achieved. The perception test indicates that by using PWs as the lowest prosodic units a speech sounds more natural and acceptable than by using LWs. This paper is supported by NSFC Project (60503071); 973 Natural Basic Research Program of China (2004CB318102); Postdoctor Science Foundation of P. R. China (20070420275).     

Critical Configurations for 1-View in Projections from ℙ<Superscript>k</Superscript> → ℙ<Superscript>2</Superscript>

In this paper we describe, from a theoretical point of view, critical configurations for the projective reconstruction of a set of points, for a single view, i.e. for calibration of a camera, in the case of projections from ℙ^k to ℙ² for k ≥ 4. We give first a general result describing these critical loci in ℙ^k, which, if irreducible, are algebraic varieties of dimension k−2 and degree 3. If k=4 they can be either a smooth ruled surface or a cone and if k = 5 they can be a smooth three dimensional variety, ruled in planes, or a cone. If k≥ 6, the variety is always a cone, the vertex of which has dimension at least k − 6. The reducible cases are studied in Appendix A. These results are then applied to determine explicitly the critical loci for the projections from ℙ^k which arise from the dynamic scenes in ℙ³ considered in [13]. Marina Bertolini is currently Associate Professor of Geometry at the Department of Mathematics at the Università degli Studi di Milano, Italy. Her main field of research is Complex Projective Algebraic Geometry, with particular interest for the classification of projective varieties and for the geometry of Grassmann varieties. On these topics M. Bertolini has published more than twenty reviewed papers on national and international journals. She has been for some years now interested also in applications of Algebraic Geometry to Computer Vision problems. Cristina Turrini is Associate Professor of Geometry at the Department of Mathematics of Università degli Studi di Milano, Italy. Her main research interest is Complex Projective Algebraic Geometry: subvarieties of Grassmannians, special varieties, automorphisms, classification. In the last two years she has started to work on applications of Algebraic Geometry to problems of Computer Vision. She is author or co-author of about thirty reviewed papers. She is also involved in popularization of Mathematics, and on this subject she is co-editor of some books.     

用硫酸铁铵容量法测定钛精矿中二氧化钛含量

样品在过氧化钠熔融、水浸取及盐酸酸化后，在盐酸和硫酸介质中，隔绝空气，用金属铝将钛(Ⅳ)还原至钛(Ⅲ)，以硫氰酸盐为指示剂，用硫酸铁铵标准溶液滴定。     

首钢外购焦炭质量恶化后的高炉生产实践

针对焦炭质量劣化的状况，高炉操作以活跃炉缸为主，从上下部调剂入手，采取疏导煤气、控制合理的实际风速和鼓风动能、缓解焦炭在高温区的粉化等措施，有效地改善了高炉的顺行状况，并逐步恢复高炉指标。     

硼酸铝晶须增强环氧树脂和双马来酰亚胺树脂体系的研究

本文以硼酸铝晶须为增强剂，以4，5-环氧环己烷-1，2-二甲酸二缩水甘油酯(TDE-85)，甲基纳狄克酸酐(MNA)、N，N’-二胺基二苯甲烷型双马来酰亚胺(BMI)/O，O′-二烯丙基双酚A(BA)体系分别作为基体制备晶须增强复合材料。研究了晶须对树脂的尺寸、表面处理方法、含量对树脂体系力学性能和热性能的影响；通过扫描电子显微镜(SEM)分析了浇注体的弯曲、冲击断口，研究晶须的增强机理。     

Analysis on the effectiveness of the 20-H rule for printed-circuit-board layout to reduce edge-radiated coupling

This paper presents the quantified study of the electromagnetic radiation mechanism of the 20-H rule using a numerical approach that has not yet been systematically addressed. The 20-H rule is a rule-of-thumb layout technique recommended to minimize radiated fields propagating from the edges of a printed circuit board (PCB) coupling onto nearby structures. Propagating electromagnetic fields may corrupt adjacent cable assemblies, sheet metal enclosures, and aperture openings. The magnitude of this design rule is investigated using the full-wave finite-difference time-domain (FDTD) method. An analysis on whether benefits exist from use of this rule is examined and under what conditions the rule is valid when correctly implemented. The purpose of this paper is to provide insight into the validity of the 20-H rule, recognizing that every PCB will have different simulation results. FDTD is used to capture a snapshot view of field propagation. This view allows one to determine the validity of the 20-H rule at a single point of time within a dynamic structure and what may be expected when digital components are finally added to a PCB assembly, which generally negates simulated results.