Hierarchical Evolution of High Definition Television

This paper presents an economically attractive system for the hierarchical evolution of High Definition Television (HDTV) compatible with the NTSC installed base. It describes the two main signals of this system: HDMAC-60 and HDNTSC. The first, HDMAC-60, is a feeder signal for use between the program origination and program redistribution points, and used also as a DBS emission format. The second, HDNTSC, is a delivery signal for high definition terrestrial broadcast, CATV distribution and VCR plus laser video disc applications. We propose this emission system as a means for transmitting HDTV pictures to consumers on the North American continent.     

A wavelet-based procedure for process fault detection

To detect faults in a time-dependent process, we apply a discrete wavelet transform (DWT) to several independently replicated data sets generated by that process. The DWT can capture irregular data patterns such as sharp "jumps" better than the Fourier transform and standard statistical procedures without adding much computational complexity. Our wavelet coefficient selection method effectively balances model parsimony against data reconstruction error. The few selected wavelet coefficients serve as the "reduced-size" data set to facilitate an efficient decision-making method in situations with potentially large-volume data sets. We develop a general procedure to detect process faults based on differences between the reduced-size data sets obtained from the nominal (in-control) process and from a new instance of the target process that must be tested for an out-of-control condition. The distribution of the test statistic is constructed first using normal distribution theory and then with a new resampling procedure called "reversed jackknifing" that does not require any restrictive distributional assumptions. A Monte Carlo study demonstrates the effectiveness of these procedures. Our methods successfully detect process faults for quadrupole mass spectrometry samples collected from a rapid thermal chemical vapor deposition process     

Shear transfer capacity along pumice aggregate concrete and high-performance concrete interfaces

This paper aims to present an experimental investigation on the behaviour of interfaces between pumice LWAC (lightweight aggregate concrete) and HPC (high-performance concrete-high-strength and fibre-reinforced), typically found in the faces and core, respectively, of hybrid precast structural sandwich panels. The evaluation of the experimental data resulted in the derivation of a semi-empirical relationship that relates the interface strength with materials strength, interface geometry and loading parameters. A brief overview of existing shear friction theories and proposed relationships, as well as a somparison among existing models and that proposed by the authors, are also outlined in the paper.     

Reconstruction of three-dimensional objects through matching oftheir parts

The problem of re-assembling an object from its parts or fragments has never been addressed with a unified computational approach, which depends on the pure geometric form of the parts and not on application-specific features. We propose a method for the automatic reconstruction of a model based on the geometry of its parts, which may be computer-generated models or range-scanned models. The matching process can benefit from any other external constraint imposed by the specific application     

Upgrading coal-derived liquids to diesel fuel

Distilled fractions of a coal-derived liquid from the H-Coal process were upgraded to diesel fuel by catalytic hydrotreatment. The total hydrotreated products were distilled into naphtha (<180°C) and diesel fuel fractions (>180°C) and the diesel fractions were analysed for hydrocarbon-type composition, hydrogen content and some diesel fuel properties. GC—MS-analyses were carried out on the hydrocarbon-type fractions to identify individual chemical compounds. To investigate the effect of different distillation cut points on diesel fuel yield and properties, cut points for one hydrotreated product were varied. The diesel fuel cetane numbers were correlated with percentage hydrogen, total aromatics and saturates. Cetane numbers above 40 were obtained for diesel fuels containing (i) more than 75% saturates, (ii) less than 15% total aromatics and (iii) a hydrogen content above 12.8%. Compounds identified by GC—MS-analyses (in the diesel fractions) were typical aromatic and cycloparaffin compounds. Normal-and iso-paraffin compounds were not detected. By varying the distillation cut point from 135 to 180°C, the cetane number of the residual diesel fraction improved from 37 to 44. This increase is ascribed to the removal of aromatic compounds in the 135–180°C boiling point range.     

The heater test at the Grimsel Rock Laboratory: The thermo-mechanical response of the rock mass to a heat flux

The Grimsel Test Site (Felslabor Grimsel — FLG) is situated at a depth of 450 m in the Juchlistock massif of the Bernese Oberland. It is managed by the National Cooperative for the Storage of Radioactive Waste (NAGRA-Switzerland).By means of a heater test, the power output of canisters filled with high-level waste is simulated. This heater test is performed by the German Gesellschaft für Strahlen- und Umweltforschung — GSF. Two electrical heaters, with a heatable length of 6 m, a diameter of 0.3 m and an available power of 4 kW/m, are installed in two vertical boreholes. One of them is located in the granite adjacent to a strongly fractured lamprophyre vein, the other one directly within this disturbed zone. They are operating since August 1986.The thermo-mechanical reaction of the rock mass is registered by a large number of measurement devices which are installed in an array of instrument boreholes around the heaters. They record the deformation and the alteration of rock stresses, the pore water pressure and the water conductivity caused by heating.     

Scrubbing Hydrogen Sulfide from Gases. A Rational Approach

Worsening of the environmental situation in many regions of Russia in recent decades is to a great degree due to production and refining of oil and gas with a high hydrogen sulfide content. Industrial methods of utilization of hydrogen sulfide are extremely irrational: it is either burned in flares or used for production of sulfur whose quality and quantity pose new problems related to its use.     

ACTION RESEARCH ON REDLINING: METHODOLOGICAL WEAKNESSES,SOCIO-POLITICAL STRENGTHS*

A chronological review and methodological critique of action research on redlining in 15 communities is presented. Redlining studies have been conducted or sponsored by three types of researchers: 1) non-profit neighborhood organizations, 2) academic or governmental institutions, and 3) lending institutions. Their findings vary according to the methods employed, and these methods vary according to the sponsors. Despite the methodological difficulties and inadequacies of this type of research, the findings have been used by local neighborhood organizations as a strategy to achieve constructive change in neighborhood reinvestment and revitalization.