Prediction of brittle-to-ductile transitions in polystyrene

In this study it is attempted to predict brittle-to-ductile transitions (BDTs) in polystyrene blends, induced either by an increase in temperature or by a decrease in inter-particle distance. A representative, two-dimensional volume element (RVE) of a polystyrene matrix with 20% circular voids, is deformed in tension. During deformation a hydrostatic-stress based craze-nucleation criterion [1] is evaluated. The simulations demonstrate that crazes initiate at low temperatures while a transition from crazing to shear yielding (BDT) is found around 75 °C. The numerical results correlate well with tensile tests on similar heterogeneous polystyrene. The presence of an absolute length, as experimentally found, is more difficult to explain. Near a free surface a T_g-depression is measured for polystyrene and also the resistance to indentation in polystyrene is lower than expected from bulk properties. Both observations are rationalised by an enhanced segmental mobility of chains near a free surface. As a consequence of these findings, an absolute length-scale could be incorporated in the numerical simulations. For simplicity, the length-scale is modelled by taking a temperature gradient over a thin layer near the internal free surfaces of the RVE. Deformation of the RVE with different absolute length-scales shows that indeed also the experimentally found brittle-to-ductile transition can be predicted if the ligament thickness between the inclusions (‘voids’) in polystyrene is below a critical value of ca. 15 nm.     

Formulation of a ceramic ink for a wide-array drop-on-demand ink-jet printer

This paper describes the methodology for simulating a reprographic ink with a ceramic ink based on a commercially available zirconia powder for direct ceramic ink-jet printing. Of over-riding importance was matching viscosity and this was tested systematically by using a mineral oil–hexane binary system. Of secondary importance was adjustment of the pressure defect behind the nozzle to compensate for small differences in surface tension. The inks tested in the wide array print-head were based on low electrical conductivity liquids to avoid damage to the electroding system. The organic binder for the zirconia ink was paraffin wax and the dispersant was a hydroxystearic acid based polyester.     

Analysis of an extensive measurement program developed from the start up to the follow up of the operation of the CNAAA NPP

Integrated tests (IT) applied to the Units I and II of the CNAAA Nuclear Power Plants (Angra dos Reis, Rio de Janeiro, Brazil) vara part of a comprehensive test program required to have the commercial operational licence issued. The IT cover operation at zero power and the subsequent power levels (the power escalation) until the nominal power operation.

This paper reports and compares the results of systematic neutron and gamma equivalent dose-rate measurements performed inside and outside the reactor containment of each Unit, during the start-up phase of the operation, for different power levels of the reactors. It also compares the collective-doses measured along the operation of the two units of the CNAAA wich similar data of the Grafenrheinfeld nuclear power plant (Germany) — basic-of-project for the CNAAA — Unit II — and analyses the data under the fight of the state-of-art.     

Practical OSPF traffic engineering

Open Shortest Path First (OSPF) traffic engineering (TE) is intended to bring long-awaited traffic management capabilities into IP networks, which still rely on today's prevailing routing protocols: OSPF or IS-IS. In OSPF, traffic is forwarded along, and split equally between, equal cost shortest paths. In this letter, we formulate the basic requirements placed on a practical TE architecture built on top of OSPF and present a theoretical framework meeting these requirements of practicality. The main contribution of our work comes from the recognition that coupled with an instance of the maximum throughput problem there exists a related inverse shortest-path problem yielding optimal OSPF link weights.     

Techniques for high-frequency integrated test and measurement

This paper describes techniques for the on-chip measurement of high-frequency and/or high-bandwidth electrical phenomena in ultra large-scale integration environments. The techniques rely on the integration of multiple compact and robust electronic test devices, or cores, at various locations within an integrated circuit. The cores consist primarily of signal generators that approximate the output of a sigma-delta modulator using finite repetitious bit patterns and a small set of highly robust analog components. They are capable of digitizing on-chip signals at gigahertz rates even using low-cost manufacturing processes. Simple communication between the multiple cores enables the migration of many "board-level" type measurements down to the chip level.     

Relevance of coupling effects on DRA array design

A finite-difference time-domain (FDTD) approach is proposed in order to obtain suitable criteria for the design of a four-element dielectric resonator antenna (DRA) array. The numerical analysis is focused on the study of the electromagnetic coupling phenomena arising between DRA fed by a microstrip-slot transition. Scattering parameters behavior and radiation patterns are determined by taking advantage of the geometrical symmetry of the structure, analyzing only one half or one quarter of the entire domain through two or four separate FDTD runs.     

PNNI-based control plane for automatically switched optical networks

Much effort has been spent on the definition of control plane protocols for automatically switched optical networks (ASON). Most of the proposals brought into the standardization for an International Telecommunications Union-Telecommunication Sector, Internet Engineering Task Force, and Optical Internetworking Forum are based on Internet protocol concepts. One such proposal is the generalized multi-protocol label switching (GMPLS), an extension of the MPLS traffic engineering control plane model that includes nonpacket switched technologies (time, wavelength, and fiber switching). Recently, the potential use of private network-network interface (PNNI) in ASONs has been discussed as an alternative proposal by the standardization bodies. The goal of this paper is to appropriately adapt asynchronous transfer mode into an optical PNNI (O-PNNI) protocol that can be used as the control plane of ASONs. The paper also provides a critical viewpoint on the potential usage of either O-PNNI or GMPLS control plane and analyzes the pros and cons of each. The methodology adopted toward devising O-PNNI hinges on reviewing PNNI along with ASON recommendations in order to determine the set of PNNI features that require adaptation. Having identified these features we engineer and present appropriate solutions relating to routing, signaling and addressing aspects.     

A fuzzy logic based-method for prognostic decision making in breast and prostate cancers

Accurate and reliable decision making in oncological prognosis can help in the planning of suitable surgery and therapy, and generally, improve patient management through the different stages of the disease. In recent years, several prognostic markers have been used as indicators of disease progression in oncology. However, the rapid increase in the discovery of novel prognostic markers resulting from the development in medical technology, has dictated the need for developing reliable methods for extracting clinically significant markers where complex and nonlinear interactions between these markers naturally exist. The aim of this paper is to investigate the fuzzy k-nearest neighbor (FK-NN) classifier as a fuzzy logic method that provides a certainty degree for prognostic decision and assessment of the markers, and to compare it with: 1) logistic regression as a statistical method and 2) multilayer feedforward backpropagation neural networks an artificial neural-network tool, the latter two techniques having been widely used for oncological prognosis. In order to achieve this aim, breast and prostate cancer data sets are considered as benchmarks for this analysis. The overall results obtained indicate that the FK-NN-based method yields the highest predictive accuracy, and that it has produced a more reliable prognostic marker model than both the statistical and artificial neural-network-based methods.