POP-IN AND CRACK ARREST IN AN HY80 WELD

It is generally thought that, when a material is in its brittle to ductile transition, it is more difficult to design for crack arrest than to prevent crack initiation (cleavage). This report shows that this is not always true for weldments. Comparison is made between compact crack arrest (CCA), K_a, and crack tip opening displacement (CTOD), K_Jc, toughness for the same HY80 weld. The value of K_a is shown to be much higher than the minimum K_Jc for pop-in fracture initiation. It is considered that the results support the conclusion of Japanese research workers (Arimochi and Isaka) that small pop-ins (in the CTOD test) propagate and arrest without load drop. It follows that prediction of structural failure for weldments need not be based on minimum pop-in toughness from CTOD tests.     

89-GHz fT room-temperature silicon MOSFETs

The authors report the implementation of deep-submicrometer Si MOSFETs that at room temperature have a unity-current-gain cutoff frequency (f_T) of 89 GHz, for a drain-to-source bias of 1.5 V, a gate-to-source bias of 1 V, a gate oxide thickness of 40 Å, and a channel length of 0.15 μm. The fabrication procedure is mostly conventional, except for the e-beam defined gates. The speed performance is achieved through an intrinsic transit time of only 1.8 ps across the active device region     

Fault tolerance in FFT arrays: Time redundancy approaches

Fault tolerance in VLSI/WSI FFT arrays acquires relevance when defects and run-time faults become significant, due to large dimensions of processors and arrays. Then, both restructuring to overcome end-of-production defects and reconfiguration to overcome run-time faults are required, to achieve the dual purposes of higher yield and higher reliability.Adopting as basic FFT network the two-dimensions array that directly corresponds to the FFT flow graph, the usual structure redundancy techniques tailored for two-dimensions arrays reconfiguration are not well applicable, since the limited locality of this network leads to relevant area increase due to the augmented interconnection structure.In this paper,time redundancy is suggested as a viable alternative for the two-dimensions FFT array; two different solutions are presented, one based oninter-stage reconfiguration, the other one adoptingintra-state reconfiguration, both allowing for survival to multiple faults with limited increase of network complexity and very small hard-core sections. As usual in many time redundancy methods, both approaches result in a processing speed equal to half the processing speed granted by an ideal, fault-free device.Reliability and survival ratios to multiple faults are evaluated for the two cases, taking into account also the area increments necessary for fault tolerance. The reliability evaluations allow for a direct comparison of the two solutions.     

Occlusion-resistant camera design for acquiring active environments.

In this article, we present a detailed theoretical analysis and a prototype implementation of a family of cameras designed with the explicit goal of detecting and removing interfering dynamic occluders in real time, during live capture, as opposed to fixing the resulting artifacts a posteriori. Such an early-acquisition approach improves efficiency: more valid samples are acquired faster without worrying about moving occluders. One option for designing a camera to be unaffected by moving occluders is to sample through the occluder, but true x-ray-like vision is technically impractical. Another option is to sample around the occluder using a camera with a large effective aperture, but such an approach requires a bulky acquisition device. Yet another possibility of sampling around an occluder is to rely on second and higher order reflected rays that indirectly sample surfaces not directly visible. However, devising an acquisition device sufficiently sensitive and efficient to capture large environments using reflected rays will remain challenging for the foreseeable future.     

Mesa and planar SiGe-HBTs on MBE-wafers

SiGe-HBTs have the potential for outstanding analog and digital or mixed-signal high frequency circuits widely based on standard Si technology. Here we review on MBE grown transistors and circuits. Processes and results of a research-like SiGe HBT and two possible production relevant HBT versions are presented. The high frequency results with f_max and f_T up to 120 GHz and a minimum noise figure of 0.9 dB at 10 GHz demonstrate the advantage of using MBE samples with steep and high base doping and high germanium contents. A comparison to the concept of reported low doped, low germanium and triangular profiled SiGe base layers, realized by UHV-CVD, is given. In addition, some circuit demonstrators of SiGe-ICs will be presented.     

Single-Step Granulation Method with Microwaves: Preliminary Studies and Pilot Scale Results

Common pharmaceutical excipients and compounds were dried either by a simple convection method or by a combined convection and microwave method in a static bed or by a combined microwave and vacuum method in a mixed bed. A simple placebo granulation was dried by an exclusive vacuum method and by a combined microwave and vacuum method in a mixed bed. The results were compared.     

Swords to plowshares: Shock wave applications to advanced lithography

xtreme ltra iolet ithography (EUVL) seeks to apply radiation in a wavelength region centered near 13 nm to produce microcircuits having feature sizes 0.1 micron or less. A critical requirement for the commercial application of this technology is the development of an economical, compact source of this radiation which is suitable for lithographic applications. A good candidate is a laser-plasma source, which is generated by the interaction of an intermediate intensity laser pulse (up to 10¹² W/cm²) with a metallic target. While such a source has radiative characteristics which satisfy the needs of an EUVL source, the debris generated during the laser-target interaction strikes at the economy of the source. Here, we review the use of concepts and computer modeling, originally developed for hypervelocity impact analysis, to study this problem.     

Screening and characterization of microorganisms with glutaryl-7ADCA acylase activity

A screening of microorganisms producing glutaryl-7ADCA acylase, an enzyme able to hydrolyse glutaric acid selectively from glutaryl-3-deacetoxy-7-aminocephalosporanic acid (glutaryl-7ADCA), has been carried out in soil samples. Five microorganisms expressing acylase activity were isolated and classified as Bacillus cereus, Achromobacter xylosooxidans, Bacillus sp., Pseudomonas sp. and Pseudomonas paucimobilis. The screening was carried out by preparing enrichment cultures containing glutaryl-7-ADCA or cephalosporin C as the selective carbon source. Four model compounds (adipoyl-, glutamyl- and glutaryl-p-nitroanilide and glutarylcoumarin), mimicking the glutaryl-7ADCA beta-lactam moiety, were synthesized as substrates suitable for the rapid screening of the microorganisms (2500) isolated from the enrichment cultures. A total of 300 strains were active on the model substrates and only 5 displayed acylase activity on glutaryl-7ADCA. The fermentation parameters, such as pH and inducer concentration, for the optimal acylase expression and acylase specificity towards the model substrates were different for each strain.     

Possibility of Using a High-Pressure Pneumatic Pump in the Porcelain Industry

The advantages and disadvantages of using a high-pressure pneumatic pump at porcelain and insulator works are discussed. The testing results of a prototype pump are described.