A Distributed State Estimator Utilizing Synchronized Phasor Measurements

With the creation of balancing authorities by the North American Reliability Council that span large portions of the North American interconnection, and stringent requirements for real time monitoring of power system evolution, faster and more accurate state estimation algorithms that can efficiently handle systems of very large sizes are needed in the present environment. This paper presents a distributed state estimation algorithm suitable for large-scale power systems. Synchronized phasor measurements are applied to aggregate the voltage phase angles of each decomposed subsystem in the distributed state estimation solution. The aggregated state estimation solution is obtained from the distributed solution using a sensitivity analysis based update at chosen boundary buses. Placement of synchronized phasor measurements in the decomposed subsystems is also investigated in this paper. Test results on the IEEE 118-bus test bed are provided     

Anfangsvorgänge bei Lichtenbergschen Figuren

Zusammenfassung Aufnahmen von Lichtenbergschen Figuren mit kurzen Spannungsstößen zeigen, daß bisher bekanntgewordene Bilder solcher Entladungsfiguren bereits ein verhältnismäßig weit vorgeschrittenes Stadium darstellen. Es gelingt mittels kurzer Stöße erste lawinenartige Anfänge der Figuren festzuhalten und einiges über Vorgänge im Anfangsstadium herauszulesen. Die negative Figur beginnt lawinenförmig an bevorzugten Stellen der Kathode. Bei nebeneinander entstandenen Lawinen ist sehr gut die gegenseitige Abstoßung infolge gleicher Ladung zu beobachten. Die Entladung hat einen geschichteten Aufbau. Die positiven Figuren bilden sich später aus. Es sprechen jedoch bisher keinerlei Anzeichen für ein Hinwachsen der Fäden zur Anode. Die Kanäle verjüngen sich zur Anode hin und selbst bei kurzen Stoßzeiten endet kein einziger vor der Anode. Auch die Art der gegenseitigen Abstoßung der positiven Fäden spricht mehr für ein Vorwachsen von der Anode aus. Aus den Farbaufnahmen ergibt sich für die filmschwärzende Strahlung eine Wellenlänge unter 450 m.     

Fuzzy Learning of Talbot Effect Guides Optimal Mask Design for Proximity Field Nanopatterning Lithography

Processing methods used in photonics and nanotechnology possess many limitations restricting their application areas such as high cost, inability to produce fine details, problems with scalability, and long processing time. Proximity field nanopatterning is a lithography method which surpasses these limitations. By using interference patterns produced by a two-dimensional phase mask, the technique is able to generate a submicron detailed exposure on a millimeter-size slab of light sensitive photopolymer, which is then developed like a photographic plate to reveal three-dimensional interference patterns from the phase mask. While it is possible to use simulations to obtain the interference patterns produced by a phase mask, realizing the mask dimensions necessary for producing a desired interference pattern is analytically challenging due to the intricacies of light interactions involved in producing the final interference pattern. An alternative method is to iteratively optimize the phase mask until the interference patterns obtained converge to the desired pattern. However, depending on the optimization technique used, one either risks a significant probability of failure or requires a prohibitive number of iterations. We argue that an optimization technique that is to take advantage of the physics of the problem using machine learning methods (here fuzzy learning) can lead to competent mask design. This technique is described in this letter.     

A 0.9 V 92 dB Double-Sampled Switched-RC Delta-Sigma Audio ADC

A 0.9 V third-order double-sampled delta-sigma audio ADC is presented. A new method using a combination of a switched-RC technique and a floating switched-capacitor double-sampling configuration enabled low-voltage operation without clock boosting or bootstrapping. A three-level quantizer with simple dynamic element matching was used to improve linearity. The prototype IC implemented in a 0.13 CMOS process achieves 92 dB DR, 91 dB SNR and 89 dB SNDR in a 24 kHz audio signal bandwidth, while consuming 1.5 mW from a 0.9 V supply. The prototype operates from 0.65 V to 1.5 V supply with minimal performance degradation.     

Influence of inhibitor addition on the corrosion protection performance of sol–gel coatings on AA2024

Sol–gel films are actively investigated during the last decade as possible candidates for environmentally friendly pre-treatments. However, the important drawback in this case is the lack of active corrosion protection and self-healing ability.     

Physico-chemical properties of ceramic pigments for high-temperature application

Heat resistant coatings are required primarily for stacks, exhaust pipes, reactors, space crafts and similar equipments that are permanently or occasionally exposed to elevated temperatures. High-temperature coatings are generally based on silicone resin with ceramic and metallic pigments. In this study, iron oxide, cobalt oxide (thermo chromic compound) and aluminum oxide are used for the preparation of four new types of coloured pigments. The thermal resistant characteristics of these ceramic pigments were studied by differential thermal analysis, thermo gravimetric analysis and differential scanning calorimetric analysis. These ceramic pigments are found to be thermally stable up to 400 °C.     

Preparation and characterization of chitosan‐based dispersions

Complexation of chitosan in aqueous solutions by low molecular weight electrolytes is one of the simplest methods for the preparation of aqueous chitosan dispersions. In this work, the influence of storage time, sulfate concentration, method of preparation and surfactant content on some properties of the resultant chitosan dispersions (turbidity, viscosity and zeta potential) was analyzed. Turbidimetry was adequate to monitor the formation of particles, while viscometry was suitable to monitor changes in the dispersing phase. An analysis of the properties of these systems, mainly in terms of particle–particle and macromolecule–macromolecule interactions was carried out. Copyright © 2004 Society of Chemical Industry     

Poly(Styrene‐Divinylbenzene) Based Media for Liquid Chromatography

The latest developments and in particular important synthetic aspects for the preparation of modern poly(styrene‐divinylbenzene) (PS‐DVB) based liquid chromatography (LC) supports are reviewed. In this context, the chemistry of particular porous and nonporous, functionalized, monolithic, coated silica and more specialized mixed organic PS‐DVB media is covered. Special consideration is given to modern approaches such as micro‐(μ)‐HPLC and coating techniques and their most important applications. Synthetic particularities relevant to the corresponding applications are outlined.