Analysis of the Survivability of GaN Low-Noise Amplifiers

This paper presents a detailed analysis of the stressing mechanisms for highly rugged low-noise GaN monolithic-microwave integrated-circuit amplifiers operated at extremely high input powers. As an example, a low-noise amplifier (LNA) operating in the 3-7-GHz frequency band is used. A noise figure (NF) below 2.3 dB is measured from 3.5 to 7 GHz with NF<1.8 dB between 5-7 GHz. This device survived 33 dBm of available RF input power for 16 h without any change in low-noise performance. The stress mechanisms at high input powers are identified by systematic measurements of an LNA and a single high electron-mobility transistor in the frequency and time domains. It is shown that the gate dc current, which occurs due to self-biasing, is the most critical factor regarding survivability. A series resistance in the gate dc feed can reduce this gate current by feedback, and may be used to improve LNA ruggedness     

Breakdown behavior of GaAs/AlGaAs HBTs

Avalanche breakdown behavior at the collector junction of the GaAs/AlGaAs HBT (heterojunction bipolar transistor) has been studied. Junction breakdown characteristics displaying hard breakdown, soft breakdown, and negative resistance breakdown behavior were observed and are interpreted by analysis of localized microplasma effects, uniform microplasma-free behavior, and associated current gain measurements. Light emission from the collector-base junction of the GaAs/AlGaAs HBT was observed and used to investigate breakdown uniformity. Using a simple punchthrough breakdown model, the theoretical breakdown curves at different collector doping concentrations and thicknesses were computed and found to be in agreement with maximum breakdown voltages measured from devices displaying the most uniform junction breakdown. The serious current gain degradation of GaAs/AlGaAs HBTs at low current densities was analyzed in connection with the measurement of a large collector-emitter breakdown voltage. The unexpected functional relationship between the collector-emitter breakdown voltage and collector-base breakdown voltage is explained by the absence of a hole-feedback effect for devices not exhibiting transistor action     

External heat transfer in infiltrated granular beds. Experimental study

Experimental data was obtained on external heat transfer in infiltrated granular beds of coarse particles. It was determined that calcualtions with the proposed model agree satisfactorily with the experimental results.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 53, No. 6, pp. 919–923, December, 1988.     

Heat transfer at the base of a cylindrical cavity oriented perpendicular to a freestream flow

The average and local heat transfer at the base surface of a cylindrical cavity whose opening is perpendicular to an oncoming freestream have been determined experimentally. During the course of the experiments, the cavity depth was varied from zero to 65% of the diameter, while the freestream Reynolds number ranged between about 5000 and 50,000. The average heat transfer coefficient decreased sharply with increasing cavity depth, the reduction being slightly greater than 50% at a depth-diameter ratio of 0.10 and greater than 90% when the depth-diameter ratio was 0.65. For the finite-depth cavities, the local heat transfer coefficient attained its maximum value at the center of the base surface and decreased with increasing radial distance from the center until a minimum was reached, after which there was a moderate increase adjacent to the outer edge of the base. The minimum occurred at the location where the radial outflow along the base separated from the surface, and a toroidal-shaped recirculation zone occupied the corner region at the intersection of the cavity base and side wall. In contrast, for the zero-depth cavity (i.e. a free disk oriented perpendicular to the oncoming flow), the local coefficient attained its minimum at the center of the surface and increased with increasing radial distance from the center.     

A dynamic linear programming approach to market allocation of renewable resources in the italian energy system: The case of solar thermal and biogas technologies

In Italy solar thermal energy and energy from biogas are two possible means of reducing dependence on energy imports. Using a multiperiod LP model (MARKAL) the authors assessed the likely potential of both technologies under various circumstances. The study covered the period 1980–2005, in five segments of five years. It focused only on the subsystem of the energy end-uses which can be substituted for by solar thermal and biogas technologies. The overall non-renewable sources which can be saved in 20 years by these technologies total 450 PJ (1 PJ = 10^{1 5} J) if the fuel prices rise at 0 per cent average annual, 1450 PJ if the fuel prices rise at 4.2 per cent average annual, 1860 PJ if the fuel prices rise at 7.2 per cent average annual and 3780 PJ if the fuel prices rise at 15 per cent average annual. However the most competitive technologies appear to be solar water heaters used mainly in the private and commercial sectors and biogas systems used mainly in the agricultural sector. The study was carried out by APRE under ENEA (formerly CNEN) contract and was intended to serve as an analytical basis for establishing an overall development and demonstration strategy for end-use renewable technologies in Italy.     

From practical methods to theoretical foundations

The year 2006 marks the ninetieth anniversary of the air navigation (later called navigation) service of the Air Forces of this country. The history of air navigation is investigated, and an opinion about its modern state and directions of further development is presented.