Sub-ambient cold-start emissions reduction using SwRI® PO x catalyst technology

This paper describes the application of SwRI’s cold-start PO _x catalyst technology to reduce cold-start hydrocarbon emissions from a US Tier 2 vehicle at −7 °C. A reduction in −7 °C (20 °F) cold-start hydrocarbons will help US Tier 2 vehicles meet the proposed EPA NMOG standards. Improvements in cold temperature hydrocarbon emissions would also be beneficial in many parts of Europe during the winter months. In this work, a total hydrocarbon reduction of 19% was realized at 24 °C, in line with previous results, but only up to 3% at −7 °C. Insufficient oxygen in the engine-out exhaust gas at −7 °C was determined to be the reason why the PO _x catalyst failed to significantly reduce HC emissions. Addition of supplemental oxygen to the exhaust during the cold-start, to simulate an adjustment in the engine calibration to less rich operation, resulted in a total hydrocarbon reduction of 18% with the PO _x catalysts in place, but no benefit when the PO _x catalysts were removed. Hence, the PO _x catalyst approach can be used to good effect, even under sub-ambient cold-start conditions.     

Feeding response of Ips paraconfusus to phloem and phloem metabolites of Heterobasidion annosum-inoculated ponderosa pine,Pinus ponderosa

In studies of feeding by the bark beetle, Ips paraconfusus, two pine stilbenes (pinosylvin and pinosylvin methyl ether), ferulic acid glucoside, and enantiomers of the four most common sugars present in ponderosa pine phloem (sucrose, glucose, fructose, and raffinose) did not stimulate or reduce male feeding when assayed on wet -cellulose with or without stimulatory phloem extractives present. When allowed to feed on wet -cellulose containing sequential extracts (hexane, methanol, and water) of ponderosa pine phloem, methanol and water extractives stimulated feeding, but hexane extractives did not. Males confined in wet -cellulose containing aqueous or organic extracts of culture broths derived from phloem tissue and containing the root pathogen, Heterobasidion annosum, ingested less substrate than beetles confined to control preparations. In an assay using logs from uninoculated ponderosa pines, the mean lengths of phloem in the digestive tracts increased as time spent feeding increased. Males confined to the phloem of basal logs cut from ponderosa pines artificially inoculated with H. annosum ingested significantly less phloem than beetles in logs cut from trees that were (combined) mock-inoculated or uninoculated and did not contain the pathogen. However, individual pathogen-containing treatments were not significantly different from uninoculated controls. It was concluded that altered feeding rates are not a major factor which may explain why diseased ponderosa pines are colonized by I. paraconfusus.     

EVAPORATION FROM POROUS MEDIA: A CAPILLARY MODEL OF A PENETRATING FRONT

A capillary tube model was solved to investigate the influence of mass transfer coefficient, temperature, and front depth on the evaporation rate during the penetrating-front period of water-filled porous media dried in hot air. The results show that increasing the flow rate of the drying air is not so efficient as increasing the sample temperature. Due to attenuating diffusion rate, the rate of liquid front migration decreases with time. The calculations explain the falling rate period behavior of sandstone heated at 121°C. Trends depicted by the model may be useful for the design of heating conditions for drying processes.     

Non-Isothermal crystallization of isotactic polypropylene in dotriacontane. II: Effects of dilution,cooling rate,and nucleating agent addition on growth rate

Non-isothermal crystallization growth rates of nucleated and non-nucleated isotactic polypropylene (iPP) in dotriacontane were determined experimentally by thermal optical microscopy. Adipic acid was used as the nucleating agent. The non-isothermal growth rates of the nucleated and non-nucleated systems were compared with experimentally determined isothermal growth rates. The Lauritzen and Hoffman growth rate equation, originally developed for isothermal crystallization, was modified to describe the non-isothermal growth. The modified Lauritzen-Hoffman equation was used to predict isothermal growth rates from non-isothermal crystallization for the nucleated and non-nucleated polymer-diluent mixtures. This study is the first to deal with polymer-diluent-nucleating agent systems vital to membrane production.     

Compatibilization of polymer blends from poly(styrene‐co‐acrylonitrile) and polycarbonate by oxazoline modification of poly(styrene‐co‐acrylonitrile) in the melt

A good way of achieving compatibility in polymer blends of poly(styrene‐co‐acrylonitrile) (S/AN) and bisphenol A polycarbonate (PC) is the chemical modification of S/AN in the melt. A catalyzed reaction of the nitrile groups with a substituted 2‐amino alcohol or 2‐amino phenol resulted in a conversion of nitrile groups of 55–75% in 60 min. The introduced heterocyclic structures were ethyl hydroxymethyl oxazoline (EHMOXA) and benzoxazole (BenzOXA), respectively. The use of dibutyltin oxide as a catalyst led to the highest efficiency. The modified polymer was characterized by Fourier transform infrared and NMR spectroscopy, elemental analysis, and reactions with organic acids and anhydrides. The modified S/AN showed good technical compatibility (single glass‐transition temperature) with PC in blends made from solution and from the melt. All blends were characterized with oscillating rheometry and differential scanning calorimetry. Rheological measurements showed that EHMOXA–S/AN reacted with PC and had crosslinked structures, whereas BenzOXA–S/AN showed compatibilization without any (crosslinking) reaction. The melt blends of BenzOXA–S/AN and PC showed a downward shift in the complex viscosity due to the influence of the BenzOXA group. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2322–2332, 2003     

Creep and Creep Fracture in Hot-Pressed Alumina

The creep and creep fracture behavior of two hot-pressed aluminas are presented, for both flexural and tensile testing. Steady-state power-law creep is observed with a stress exponent of about 2 for each material. Three distinct fracture regimes are found. At high stress in flexure, fracture occurs by slow crack growth with a high stress dependence of the failure time. At intermediate stresses, in both flexure and tension, creep fracture occurs by multiple microcracking after modest strains. Failure times exhibit a modest stress dependence (stress exponent of 2.5 in tension and 3 in flexure), with a constant failure strain equal to 0.09. The failure times are considerably longer in flexure than in tension, because of the constraint imposed on crack growth by the bending geometry. We conclude that flexure cannot be used for creep lifetime assessment, even in simple, single-phase materials such as Al₂O₃. At low stresses, in tension, failure also exhibits a modest stress dependence but with a much higher failure strain. The material shows the onset of super-plastic behavior.     

—Review Paper—Current State-Of-The-Art Measurements Of Ozone In The Gas Phase And In Solution

This paper is a critical review and summary of the analytical procedures currently used by operating water utilities to control ozone treatment processes, considering disinfection as well as the many oxidative applications of ozone in water treatment applications. The role of common interferences in the various methods is described.

In operating U S., Canadian, European, and Japanese water treatment plants currently employing ozone as a primary disinfectant, ozone nearly always is followed by the addition of small quantities of chlorine, chlorine dioxide, or chloramine to provide the residual in the distribution system and to act as a secondary disinfectant. Clearly, the analytical procedures used must distinguish between the various species. This review critically presents these various factors and their implication with respect to “true values” of ozone determined under widely varying conditions.     

Surface mass transfer processes using peat as an adsorbent for dyestuffs

The factors affecting the initial rate of Telon Blue (Acid) dye adsorption onto peat have been investigated. The surface mass transfer coefficients for the rate of dye removal from solution have been determined and correlated as the dimensionless mass transfer term Sh/Sc^0.33. The function Sh/Sc^0.33 has been correlated with respect to four variables, namely, agitation, initial dye concentration, peat particle size range and the temperature of the dye solution. The mass transfer term varies with T^5.5, d_p^0.13, c_o^?1.1 and R.P.M.^0.26; consequently temperature has the most pronounced effect on the mass transfer coefficient.     

The use of electrochemical noise methods (ENM) to study thick, high impedance coatings

Thick, high impedance organic coatings are those class of coatings used to provide corrosion protection to naval vessels, pipelines, gasoline storage tanks, and other large structures such as bridges and plant structures. These coatings, especially the newest generations now being used in practice, can provide exceptional protection and lifetime of performance such that properly and accurately assessing and differentiating among competing coatings is a very difficult task. The standard protocol of salt fog testing (ASTM B117), immersion testing, and outdoor exposure in a corrosive environment with subjective evaluation of a coating's performance durings and after testing, does not adequatcly rank and predict coating lifetimes for new coating systems, especially for the environmentally compliant coating systems such as powder coatings (especially the thick, fusion bonded epoxy (FBE) coatings used for pipelines), two component epoxy and urethane coatings and waterborne coatings. New, objective test methods are desperately needed by users and manufacturers of coatings. A relatively new electrochemical test procedure, electrochemical noise methods (ENM), as developed by Skerry and Eden, has been shown in our laboratory to be very successful in the ranking and prediction of relative coating performance. We have used the method successfully on naval ship coatings, several pipeline coatings and other related systems, and Skerry has used them successfully on industrial maintenance coatings. We have used these methods in conjunction with electrochemical impedance spectroscopy, d.c. resistance measurements and cyclic salt fog testing of the Prohesion^TM type. In our studies of pipeline coatings, we needed to investigate thermal effects because of their extended range of use temperature. In these studies, we have discovered that electrochemical methods can be used for an in situ measurement of the T_g of coatings in electrolyte immersion. Further, the ‘plasticizing’ effect of aqueous electrolyte absorption as well as its relative irreversibility has been shown. For all coatings studied, ENM provided useful, objective, numerical data which rapidly ranks coatings and provides useful information on the relative lifetime prediction of coatings which may provide up to 30 years of service.     

(<Emphasis Type="Italic">Z,Z</Emphasis>)-6,9-Heneicosadien-11-One: Major Sex Pheromone Component Of Painted Apple Moth, <Emphasis Type="Italic">Teia anartoides</Emphasis>

(Z, Z)-6,9-Heneicosadien-11-one (Z6Z9-11-one-21Hy) was identified as the major sex pheromone component of the painted apple moth (PAM), Teia anartoides (Lepidoptera: Lymantriidae), on the basis of (1) comparative gas chromatographic-electroantennographic detection (GC-EAD) analyses, GC-mass spectrometry (MS), high-performance liquid chromatography (HPLC)-MS, and HPLC-UV/visible spectroscopy of pheromone gland extracts and authentic standards; (2) GC-EAD analyses of effluvia of calling females; and (3) wind tunnel and field trapping experiments with a synthetic standard. In field experiments in Australia, synthetic Z6Z9-11-one-21Hy as a single component attracted male moths. Wind tunnel experiments suggested that a 4-component blend consisting of Z6Z9-11-one-21Hy, (6Z,9R,10S)-cis-9,10-epoxy-heneicosene (Z6-9R10S-epo-21Hy), (E, E)-7,9-heneicosadien-6,11-dione (E7E9-6,11-dione-21Hy), and 6-hydroxy-(E, E)-7,9-heneicosadien-11-one (E7E9-6-ol-11-one-21Hy) (all present in pheromone gland extracts) might induce more males to orient toward, approach, and contact the source than did Z6Z9-11-one-21Hy as a single component. Additional experiments are needed to determine conclusively whether or not Z6-9R10S-epo-21Hy, E7E9-6,11-dione-21Hy, and E7E9-6-ol-11-one-21Hy might be minor sex pheromone components of PAM. Moreover, attractiveness of synthetic pheromone and virgin PAM females needs to be compared to determine whether synthetic pheromone could replace PAM females as trap baits in the program to monitor eradication of exotic PAM in New Zealand.