Factors affecting cloud point analysis of palm oleins

Some of the factors affecting cloud point determination of palm oleins are described. These are the type of container used, method of stirring, rate of stirring and bath temperature. The repeatability and reproducibility standard deviations of the method are determined from collaborative trials. Recommendations for the test are made to reduce the large variations among laboratories.     

Stability studies on methyl and ethyl fatty acid esters of sunflowerseed oil

Fatty acid esters, high in linoleic acid, were prepared and stored for long-term engine tests. Storage tests with these esters were undertaken to obtain more information on optimal storage requirements and general stability characteristics. Samples were kept at three temperature levels (20 C, 30 C and fluctuating around 50 C) for a 90-day period and were removed at regular intervals for chemical and physical analysis. The influence of air, temperature, light, TBHQ and contact with mild steel was evaluated by comparing the free fatty acid, peroxide, anisidine, ultraviolet absorption, viscosity and induction periods. A statistical model was used to evaluate the data and to reduce the large number of data points to comparable curves. Storage of esters in contact with air, especially at a temperature above 30 C, resulted in significant increases in peroxide, ultraviolet absorption, free fatty acid, viscosity and anisidine values. Exclusion of air retarded oxidation at all temperature levels. A direct relationship between viscosity increases and oxidation parameters was evident. Exposure to light caused a small increase in the oxidation parameters of esters stored at the highest temperature level. Addition of TBHQ prevented oxidation of samples stored under moderate conditions. Under unfavorable storage conditions the anti-oxidant was no longer effective. Mild steel had very little effect on the oxidation parameters. Only the anisidine values of samples stored at the highest temperature level were slightly increased. Methyl esters performed slightly better than ethyl esters during the storage test. The following practical guidelines for storage of fatty acid ester fuels are: (i) airtight containers should be used; (ii) the storage temperature should be <30 C; (iii) mild steel (rust free) containers may be used, and (iv) TBHQ has a beneficial effect on oxidation stability.     

Performance of combined cobalt—nickel—zirconia and HZSM-5 catalyst systems for carbon monoxide hydrogenation

The synthesis of hydrocarbons via hydrogenation of carbon monoxide was investigated over cobalt—nickel—zirconia catalysts of various compositions in combination with zeolite HZSM-5 in “mixed bed” and “follow bed” arrangements. These combinations resulted in the formation of aromatics in amounts as high as 30-35 wt% under relatively mild operating conditions (1 atm, 250–280°C). Although the olefinicity of C₂ and C₃ fractions in the product stream was higher in the mixed bed compared to the follow bed arrangement, the selectivities to aromatics were comparable in the two bed arrangements. The aromatic selectivity was found to be sensitive to operating conditions. The formation of aromatics was favored at high HZSM-5/metal catalyst ratios, low space velocities and high reaction temperatures. The product distributions obtained using various metal/zeolite bifunctional catalysts have been discussed.     

Anaerobic biodecolorization of textile reactive anthraquinone and phthalocyanine dyebaths under hypersaline conditions.

The biological decolorization of two industrial, spent textile reactive dyebaths was investigated using a suspended-growth, halophilic mixed culture fed with glucose. Dyebath I contained mainly Reactive Blue 19 (RB19), an anthraquinone dye, whereas dyebath II contained mainly Reactive Blue 21 (RB21), a phthalocyanine dye. Batch assays under anaerobic conditions with the two neutralized dyebaths resulted in 87 and 37% extent of decolorization for dyebaths I and II, respectively. The rate of glucose utilization and the extent of acetate production were impacted in the presence of each dyebath as compared to the control culture. However, dyebath decolorization occurred despite moderate culture inhibition. Reuse of a biologically renovated RB19-containing dyebath in the dyeing process resulted in reproducible but not identical cotton fabric shades as compared to a standard dyeing (i.e., control) using fresh water. This difference is attributed to a variable degree of RB19 aggregation during the dyeing process and is not related to the efficiency of the biodecolorization process. Further improvement of the redyeing efficiency will lead to the development of an in-plant, closed-loop decolorization system resulting in significant water conservation and minimization of textile pollutants such as salt and dyes.     

The architecture of the Sure System 2000 communications processor

Sure System 2000, a fault-tolerant computer that couples multiprocessors to offer low-priced, high-performance systems that deal effectively with faults and failures, is presented. The architecture is based on the local redundancy technique, ensuring that no hardware or software fault can cause a system crash. Software errors can be fixed, and hardware can be replaced, upgraded, or added dynamically. Existing fault-tolerant computers are briefly reviewed, and the logic hardware system configuration of the Sure System 2000 is described. The multiprocessor and I/O architecture are examined. The SXO Sure System 2000 expandable operating system is described     

Parametric modeling of somatosensory evoked potentials

In this paper, we examine methods of characterizing somatosensory evoked potentials (SEP's) in both the time and frequency domains. We have found that the truncated impulse response (TIR) method produced an accurate time domain model of the SEP signals at model orders greatly reduced from the original state space matrix. The TIR method was valuable for smoothing signals that were slightly corrupted by noise. In this case, the simulated data sequence was close to the original data sequence in the mean squared error sense. For signals that were greatly corrupted by noise, the TIR method was not able to perform as well. Therefore, the TIR method was not a feature extraction method but was valuable for data simulation. In the frequency domain, we have used the autoregressive moving average model (ARMA) to parameterize the SEP signal. An overdetermined set of Yule-Walker equations was created to determine the autoregressive (AR) parameters of the original data with the model order established by the singular value decomposition. From these AR parameters, a residual time series was generated which was used to find the moving average parameters. The resulting ARMA model was used to produce a simulated data sequence. The frequency domain characteristics of the simulated sequence and the corresponding power spectral density of the ARMA filter were very close to the periodogram of the original data sequence. Accurate parameterization was achieved for the SEP waveforms at low filter lengths.     

PHOSPHORUS AND PHOSPHATE LEVELS IN THE ALEURONE CELLS OF CEREAL GRAINS

The aleurone cells of barley, wheat, rice, rye, oats and triticale contained, comparatively, higher percentages of phosphorus than the aleurone cells of sorghum, maize or millet. The aleurone tissues of barley, wheat and rice had more phosphate than corresponding tissues of sorghum and maize. Phosphate was not detected in the aleurone tissue of maize but was found in trace amounts in the aleurone tissue of sorghum.     

Standing on Solid Ground

The new Editor in Chief of IEEE Micro introduces himself and the first issue of 2007. He thanks outgoing Editor in Chief Pradip Bose for his outstanding work on Micro during his tenure. He assesses the current state of the microarchitecture field, speculates on the future, and asks readers for their suggestions on topics the magazine should cover in coming issues.     

Schwingfestigkeit von Schraube‐Mutter‐Verbindungen

High cycle fatigue of bolted connections Extensive tests regarding the influences on the fatigue of bolt‐nut‐connections of preloading with torsion, of preloading with yielding, of loading with superimposed bending and of the tested lot are processed. These influences are not yet known according to VDI 2230. New testing devices were designed for these tests, which allow a far less expensive operation and may easily be used for bolts of diameters up to M100 and testing frequencies up to 1000 Hz. The validity of fatigue resistance according to VDI 2230 is specified with respect to the test results. The determined influence of the tested lots is unexpectedly high. The manufacturing process of bolts should be improved to minimize this influence.