Photocatalytic oxidation of low concentration 2,4-D solution with new TiO2 fiber catalyst in a continuous flow reactor.

Environmental pollution by low concentrations of 2,4-Dichlorophenoxyacetic acid (2,4-D) is a concern these days due to ever increasingly stringent regulations. Photocatalysis with immobilized TiO2 fiber is a promising oxidation method. Laboratory experiments on photocatalytic degradation of 0.045 mmol l(-1) 2,4-D with the world's first high-strength TiO2 fiber catalyst were carried out in a continuous flow reactor in which the degradations were, in general, similar to those with high 2,4-D concentrations investigated elsewhere. Degradation and mineralization of 2,4-D were significantly enhanced with no initial pH adjustments. The rate constants for total organic carbon (TOC) without pH adjustment were about two-fold bigger than the pH adjustment cases. CO2 gas measurement and carbon mass-balance were carried out for the first time, where about 34% organic carbon converted into CO2 gas during four-hour oxidation. 2,4-Dichlorophenol (2,4-DCP), phenol, benzyl alcohol and two unknowns (RT = 2.65 and 3.78 min.) were detected as aromatic intermediates while Phenol was the new aromatic in HPLC analysis. Dechlorination efficiencies were high (> 70%) in all the cases, and more than 90% efficiencies were observed in chloride mass balance. Bigger flow rates and solution temperature fixed at 20 degrees C without pH adjustment greatly enhanced 2,4-D mineralization. These results can be an important basis in applying the treatment method for dioxin-contaminated water and wastewater.     

Dominant rock properties affecting the performance of conical picks and the comparison of some experimental and theoretical results

Conical picks are the essential cutting tools used especially on roadheaders, continuous miners and shearers and their cutting performance affects directly the efficiency and the cost of rock/mineral excavation. In this study, in order to better understand the effects of dominant rock properties on cutter performance, 22 different rock specimens having compressive strength values varying from 10 to 170 MPa are first subjected to a wide range of mechanical tests. Then, laboratory full-scale linear cutting tests with different depth of cut and cutter spacing values are realized on large blocks of rock specimens using one type of conical pick. Specific energy, cutting and normal force values for relieved and unrelieved cutting modes are recorded using a triaxial force dynamometer with capacity of 50 tonnes and a data acquisition system. Cutter force and specific energy values are correlated with rock properties and theoretical force and specific energy values obtained from widely used theoretical approaches.The results indicate that uniaxial compressive strength among the rock properties investigated is best correlated with the measured cutter performance values, which is in good agreement with previous studies. However, it is also emphasized in this study that Brazilian tensile strength, Schmidt hammer rebound values, static and dynamic elasticity modulus are also dominant rock properties affecting cutter performance.Theoretical specific energy defined by different researchers has a meaningful relationship with the experimental specific energy, which is an essential parameter for predicting the instantaneous cutting rates of mechanical excavation systems. It is also demonstrated that the experimental cutter forces obtained for 5 mm depth of cut are in good agreement with theoretical force values, if the friction angle between rock and cutting tool is included in the theoretical formulation. It is emphasized that, to some extend, laboratory tests can help to minimize high cost of a trial–error approach in the field.     

Catalytic aminolysis of epoxide by alumina prepared from amine-protected Al precursor

The catalytic activities of alumina prepared from an Al alkoxide-amine adduct monomer for the reaction of cyclopentene oxide with piperidine was determined after various pretreatments, including calcination and exposure to moisture. They were compared with the activity of alumina prepared by the conventional hydrolysis method. It was found that the as-prepared sample from the alkoxide-amine monomer preparation was five times more active than a conventional preparation, suggesting that it has a higher density of surface Lewis acid sites. However, its activity was much more severely suppressed by exposure to moisture.     

Tunneling Conductance Dependence of the Tunneling Spectra in Bi2Sr2CaCu2O8

We have measured the tunneling spectra in Bi₂Sr₂CaCu₂O₈ with a scanning tunneling microscope(STM) at various tip-sample distances by changing the tunneling conductance in a controlled manner. When the tunneling conductance is increased from 1×10^–9 to 1×10^–5 S, the spectra do not show changes in particular. However, the gap value decreases steeply and the asymmetric back ground density of states turns inverted V-shaped one above 6×10^–4 S. The changes in the tunneling spectra at the high tunneling conductances are explained by the enhancement of the local carrier density induced by the pressure that the STM tip applied to the sample.     

Prediction of brittle-to-ductile transitions in polystyrene

In this study it is attempted to predict brittle-to-ductile transitions (BDTs) in polystyrene blends, induced either by an increase in temperature or by a decrease in inter-particle distance. A representative, two-dimensional volume element (RVE) of a polystyrene matrix with 20% circular voids, is deformed in tension. During deformation a hydrostatic-stress based craze-nucleation criterion [1] is evaluated. The simulations demonstrate that crazes initiate at low temperatures while a transition from crazing to shear yielding (BDT) is found around 75 °C. The numerical results correlate well with tensile tests on similar heterogeneous polystyrene. The presence of an absolute length, as experimentally found, is more difficult to explain. Near a free surface a T_g-depression is measured for polystyrene and also the resistance to indentation in polystyrene is lower than expected from bulk properties. Both observations are rationalised by an enhanced segmental mobility of chains near a free surface. As a consequence of these findings, an absolute length-scale could be incorporated in the numerical simulations. For simplicity, the length-scale is modelled by taking a temperature gradient over a thin layer near the internal free surfaces of the RVE. Deformation of the RVE with different absolute length-scales shows that indeed also the experimentally found brittle-to-ductile transition can be predicted if the ligament thickness between the inclusions (‘voids’) in polystyrene is below a critical value of ca. 15 nm.     

Formulation of a ceramic ink for a wide-array drop-on-demand ink-jet printer

This paper describes the methodology for simulating a reprographic ink with a ceramic ink based on a commercially available zirconia powder for direct ceramic ink-jet printing. Of over-riding importance was matching viscosity and this was tested systematically by using a mineral oil–hexane binary system. Of secondary importance was adjustment of the pressure defect behind the nozzle to compensate for small differences in surface tension. The inks tested in the wide array print-head were based on low electrical conductivity liquids to avoid damage to the electroding system. The organic binder for the zirconia ink was paraffin wax and the dispersant was a hydroxystearic acid based polyester.     

The extended quadratic residue code is the only (48,24,12) self-dual doubly-even code

An extremal self-dual doubly-even binary (n,k,d) code has a minimum weight d=4/spl lfloor/n/24/spl rfloor/+4. Of such codes with length divisible by 24, the Golay code is the only (24,12,8) code, the extended quadratic residue code is the only known (48,24,12) code, and there is no known (72,36,16) code. One may partition the search for a (48,24,12) self-dual doubly-even code into three cases. A previous search assuming one of the cases found only the extended quadratic residue code. We examine the remaining two cases. Separate searches assuming each of the remaining cases found no codes and thus the extended quadratic residue code is the only doubly-even self-dual (48,24,12) code.