Efficient third-harmonic generation of a picosecond laser pulsewith time delay

A new configuration based on the polarization-mismatching scheme with time delay for efficient frequency tripling conversion is proposed in this paper. The calculated results showed that the requirement for the efficient frequency tripling conversion of a 1-ps laser pulse is not only the optimization of peak intensity of the second-harmonic pulse, but also the optimization of the pulse duration ratio and temporal difference between the o-polarization second-harmonic pulse and the e-polarization first-harmonic pulse due to group-velocity mismatch among the interacting pulses. With the proposed scheme the group velocity mismatch can be compensated. Overall energy conversion efficiency increases from 55% to 75% under the optimized conditions at the intensity of 6 GW/cm². The temporal shape of the third-harmonic pulse with 1 ps pulse duration has no subpulses. The optimization of the efficient frequency tripling conversion for intensities of over 75 GW/cm² is also described. The results showed that the maximum tripling energy conversion efficiency is close to 80% with the optimized doubler and tripler     

Value of transcranial Doppler indices in predicting raised ICP in infantile hydrocephalus. A study with review of the literature

Cerebral hemodynamic changes in infants with progressive hydrocephalus have been studied with the transcranial Doppler (TCD) technique. Several authors have referred to the correlation between the hemodynamic changes and increased intracranial pressure (ICP). Despite conflicting conclusions on the value of pulsatility index (PI) and resistance index (RI) measurements for monitoring infantile hydrocephalus, these pulsatility indices are the most commonly used for this purpose. Although clinical signs of raised ICP are highly variable and unreliable in infants, assumptions have been made in most of the studies about the presence of elevated ICP on the basis of the patient's clinical state. Few studies have reported on actual ICP values, however, and a direct relationship between ICP and TCD changes has never been adequately demonstrated. In the present study, this relationship was investigated in long-term simultaneous TCD/ICP measurements, in an attempt to develop a noninvasive method of monitoring the effect of ICP on intracranial hemodynamics. Two groups of data sets were established. Group I consisted of pre- and postoperative (shunt implantation) TCD/ICP measurements. Group II were long-term simultaneous TCD/ICP recordings showing significant ICP variations. In most of the postoperative measurements there was a decrease in the average PI and RI values. The correlation between PI or RI and ICP in the long-term simultaneous recordings, however, was generally poor. The risk of obtaining false positive or false negative PI or RI values in short-term measurements was also demonstrated. It can be concluded from our results, besides the wide range of reference values for the Doppler indices and extracranial influences upon them, that the present Doppler indices are inadequate for monitoring the complex intracranial dynamic responses in patients with raised ICP.     

Room temperature characterization of Hg1-xCdxTe P-on-n heterostructure photodiodes

Measurements of 77K R_oA and 300K reverse bias dynamic impedance (R_dA) products at one volt reverse bias has been carried out to assess the degree of correlation of this figure of merit. Planar P-on-n heterostructures were grown on near lattice-matched CdZnTe substrates with Hg_1-xCd_xTe (0.20< x <0.30) by molecular beam epitaxy. These devices were passivated with CdTe and doped with indium and arsenic as n- and p-type dopants, respectively. Current-voltage characteristic of these devices exhibit thermally generated dark currents at small and modest reverse bias. We have observed that R_oA values of these long wavelength infrared P-on-n heterostructure photodiodes at 77K correlate with room temperature R_dA values. Diode arrays with high room temperature R_dA values at one volt reverse bias also have high R_oA values at 77K. Similarly, low R_dA values at room temperature indicate poor performance at 77K where deviation from diffusion current occurs at reverse bias of 0.2 to 1 volt at room temperature. The results presented here, for a small samples of devices, demonstrate that room temperature measurements of current-voltage characteristics to evaluate Hg_1-xCd_xTe (0.22< x <0.28) diode performance and array uniformity at lower temperatures can be used. This provides an acceptable criteria for further study at lower temperatures.     

Control of calcium hexaluminate grain morphology in in-situ toughened ceramic composites

The influence of processing conditions on the morphology of calcium hexaluminate (CA₆) grains in Al₂O₃: 30 vol% CaO·6Al₂O₃ (CA₆) ceramic composites was investigated. Specimens were prepared by in-situ reaction sintering using precursor powders of alumina, and either calcium carbonate or calcium oxide. In some samples, 1 vol% anorthite glass was added as a sintering aid. X-ray diffraction was used to study the phase development in the as-calcined and sintered states. The resultant microstructures were characterized using both scanning electron microscopy (SEM), and imaging secondary ion mass spectrometry (SIMS). It was found that the CA₆ grains developed a platelike morphology when CaCO₃ was used as the starting calcium-rich powder. In contrast, samples prepared using CaO resulted in equiaxed CA₆ grains. This result was observed to be independent of the anorthite glass addition. The findings are rationalized in terms of distinct CA₆ reaction mechanisms, resulting from differences in the reactivity of the powders during the early stages of calcining.Cement Nomenclature C CaO - A Al₂O₃     

Thermal decoloration kinetics of spirooxazines in Ormocer coatings prepared via sol-gel processing

Two free and one silylated (silane-substituted) photochromic spirooxazines are doped into organically modified ceramics (Ormocer) coatings by sol-gel processing and the thermal decoloration kinetics of these coatings are investigated and compared with the corresponding ethanol solutions and PMMA coatings. The decoloration behaviour of the two free dyes (SO-1 and SO-2) in the Ormocer coatings is similar to that in ethanol solutions, obeying a first-order mechanism and possessing almost the same decoloration rates as in ethanol. This suggests that the dye molecules encapsulated within the pores of the solid matrix are as free as those in ethanol solutions. The silylated dye (SO-3) in the Ormocer coatings, however, exhibits a considerably lower decoloration rate than the corresponding free dye (SO-1) and evident deviation from the first-order mechanism. This indicates apparently that the degree of freedom of the dye molecules is reduced by the silylation. These results are discussed on the basis of solvent polarity, porous structure of the Ormocer coating, and the dye-to-matrix connectivity.     

Studies on the in vitro Release of Ibuprofen from Polyethylene Glycol-Polyvinyl Acetate Mixtures Liquid Filled into Hard Gelatin Capsules

The release of ibuprofen from mixtures of polyethylene glycol (PEG) with polyvinyl acetate (PVAc) has been studied in vitro and complemented by x-ray diffraction measurements, differential scanning calorimetry (DSC), and melting point determinations via hot-stage microscopy (HSM). Results indicate that ibuprofen release can be affected markedly by alteration of the PVAc concentration. The molecular weight of the PEG and the pH of the dissolution medium are also shown to affect the release profile. Visual observation during the drug release process revealed a complex behavior which included emission of liquidlike droplets, formation of a crust around the releasing mass, and/or production of flakes of solid material. This behavior appeared to have a disadvantageous effect on the reproducibility of drug release. Construction of a phase diagram from results of thermal analysis using DSC and HSM indicated the formation of an eutectic mixture with a composition of 35% ibuprofen and 65% PEG 1500 and a melting point of 36°C. The complex behavior of the drug-releasing mass is discussed in terms of this phase diagram. Only the release data for systems containing 4% w/w or more of PVAc could be linearized by plotting against the square root of time whereas data for all of the systems studied could be linearized by first-order plots.     

Adhesion of streptococci to saliva-coated and uncoated composite-based resins

This study was designed to evaluate the bacterial adhesion to five types of experimental composite-based resins and a commercial composite resin used as a control. Physicochemical surface characteristics of composite resins with and without an artificial saliva coating were measured. The relationship between the numbers of adhering cells (Streptococcus sanguis, S. mutans and S. sobrinus) and surface characteristics was analysed. The values of contact angles and the number of adhering cells were small with saliva coating. S. sanguis ATCC 10557 showed a positive correlation (r=0.835, p<0.05) with the contact angles of uncoated resins, whereas no relationship was observed for saliva-coated resins. With S. mutans Ingbritt the cell numbers adhering to resins correlated strongly (p<0.01) with the values of zeta potential of resins for either saliva coated or uncoated. Electrical repulsion forces had a strong contribution to adherence of cells such as S. mutans and S. sobrinus which show a high absolute zeta potential.