The effect of rice bran on physicochemical,textural and glycaemic properties of ready-to-eat extruded corn snacks

In this work, corn extruded snack products were enriched with rice bran (RB) at 10% and 15%. A co-rotating twin-screw extruder was used with a feed moisture content of 16 g 100 g⁻¹, a screw speed of 240 r.p.m. and four heating sections of the barrel (100, 140, 150 and 150 °C). The impact of RB inclusion on nutritional profile, starch digestion, physicochemical and textural properties of snack products was evaluated. RB-enriched extrudates showed a lower specific volume and hardness and higher crispness than control. RB at 15% gave a water-holding capacity lower than control. Rheology of extrudate dispersions indicated an increase in elastic interactions and solid-like behaviour with RB supplementation. Differences in rheological properties resulted in attenuation of predictive glycaemic response for RB-enriched snacks.     

Thermally reused solar energy harvesting using current mirror cells

This paper implements a simultaneous solar and thermal energy harvesting system, as a hybrid energy harvesting (HEH) system, to convert ambient light into electrical energy through photovoltaic (PV) cells and heat absorbed in the body of PV cells. Indeed, a solar panel equipped with serially connected thermoelectric generators not only converts the incoming light into electricity but also takes advantage of heat emanating from the light. In a conventional HEH system, the diode block is used to provide the path for the input source with the highest value. In this scheme, at each time, only one source can be handled to generate its output, while other sources are blocked. To handle this challenge of combining resources in HEH systems, this paper proposes a method for collecting all incoming energies and conveying its summation to the load via the current mirror cells in an approach similar to the maximum power point tracking. This technique is implemented using off-the-shelf components. The measurement results show that the proposed method is a realistic approach for supplying electrical energy to wireless sensor nodes and low-power electronics.     

Difference in subsurface damage in indented specimens with and without bonding layer

This paper aims to assess the applicability of the bonded–interface technique (BIT) that has been used for examining sub-surface damage in brittle materials. With the aid of the finite element method, the indentation stress fields in alumina specimens with and without a bonded–interface were analysed. It was found that the bonded–interface greatly alters the stress distribution in the neighbourhood of the interface. The high-stress zone shifts away from the interface, and extends to the surface. Both glue layer mechanical properties and bond thickness play a limited role in the overall stress field of the BIT alumina. Comparisons of theoretical predictions with experimental observations showed that, to a great extent, the BIT presents a different pattern of sub-surface damage. The study clarifies the applicability of the BIT and offers a useful guideline for practitioners.     

Failure of silver nanowire transparent electrodes under current flow

Silver nanowire transparent electrodes have received much attention as a replacement for indium tin oxide, particularly in organic solar cells. In this paper, we show that when silver nanowire electrodes conduct current at levels encountered in organic solar cells, the electrodes can fail in as little as 2 days. Electrode failure is caused by Joule heating which causes the nanowires to breakup and thus create an electrical discontinuity in the nanowire film. More heat is created, and thus failure occurs sooner, in more resistive electrodes and at higher current densities. Suggestions to improve the stability of silver nanowire electrodes are given.     

Reservoir volume optimization and performance evaluation of rooftop catchment systems in arid regions: A case study of Birjand,Iran

This study evaluated the performance of rooftop catchment systems in securing non-potable water supply in Birjand, located in an arid area in southeastern Iran. The rooftop catchment systems at seven study sites of different residential buildings were simulated for dry, normal, and wet water years, using 31-year rainfall records. The trial and error approach and mass diagram method were employed to optimize the volume of reservoirs in five different operation scenarios. Results showed that, during the dry water year from 2000 to 2001, for reservoirs with volumes of 200–20000 L, the proportion of days that could be secured for non-portable water supply was on average computed to be 16.4%–32.6% across all study sites. During the normal water year from 2009 to 2010 and the wet water year from 1995 to 1996, for reservoirs with volumes of 200–20000 L, the proportions were 20.8%–69.6% and 26.8%–80.3%, respectively. Therefore, a rooftop catchment system showed a high potential to meet a significant portion of non-potable water demand in the Birjand climatic region. Reservoir volume optimization using the mass diagram method produced results consistent with those obtained with the trial and error approach, except at sites #1, #2, and #5. At these sites, the trial and error approach performed better than the mass diagram method due to relatively high water consumption. It is concluded that the rooftop catchment system is applicable under the same climatic conditions as the study area, and it can be used as a drought mitigation strategy as well.     

Control Optimization of a Slotted Switched Reluctance Generator for High-torque Applications

This article describes the control optimization of a slotted switched reluctance generator for low-speed applications. The machine is simulated with the finite-element method. The turn-off and turn-on angles are optimized by means of a genetic algorithm to maximize the output power and minimize the torque ripple. First, these two criteria are optimized separately with a mono-objective genetic algorithm, and then a multi-objective Pareto genetic algorithm is used. An analysis of optimized parameters and resulting current waveforms is also performed. Experimental results based on a 6/4 switched reluctance generator are also presented.     

Electromagnetic Design and Analysis of a Novel Axial-Transverse Flux Permanent Magnet Synchronous Machine

This paper analyzes a novel hybrid axial-transverse flux permanent magnet (PM) synchronous motor achieving high torque density. The stator pole pitch and the rotor pole pitch are the same. The motor is suitable for vehicle traction systems. The new axial-transverse machine has a single-sided or double-sided air gap. The machine has two adjacent quasi-U stator cores with ring-type winding, and the rotor has two PM groups, one outer and one inner. The shape of quasi-U stator core allows changing the flux path without changing power supply polarity. The analytical expressions of the no-load back-EMF and the torque are derived, after the development of 3-D magnetic equivalent circuit (MEC) model. The 3-D finite element method (FEM) is used to analyze the magnetic field, torque, and cogging torque for different skewings of the PMs.     

Co-doping effects of (Al,Ti, Mg) on the microstructure and electrical behavior of ZnO-based ceramics

Co-doped ZnO-based ceramics using Al, Ti, and Mg ions in different ratios were synthesized with the objective to investigate the doping effects on the crystalline features, microstructure and the electrical behavior. For Al and Ti doping, a coexistence of crystalline phases was shown with a major wurtzite ZnO structure and secondary spinel phases (ZnAl₂O₄, Zn₂TiO₄, or Zn_aTi_bAl_cO_d), while Mg doping did not alter significantly the structural features of the wurtzite ZnO phase. The electrical behavior induced by Al, Ti, and Mg co-doping in different ratios was investigated using Raman, electron paramagnetic resonance (EPR) and ²⁷Al and ⁶⁷Zn solid-state nuclear magnetic resonance (NMR). Al doping induces a high electrical conductivity compared to other doping elements. In particular, shallow donors from Zn_i-Al_Zn defect structures are inferred from the characteristic NMR signal at about 185 ppm; that is, quite far from the usual oxygen coordinated Al. The Knight shift effect emanating from a highly conducting Al-doped ZnO ceramics was considered as the origin of this observation. Oppositely, as Ti doping leads to the formation of secondary spinel phases, EPR analysis shows a high concentration of Ti³⁺ ions which limit the electrical conductivity. The correlation between the structural features at the local order, the involved defects and the electrical behavior as function of the doping process are discussed.     

Compressive sensing based high-resolution passive bistatic radar

Passive bistatic radar (PBR) systems using different communication signals can only offer low-resolution target detection due to their inherent low bandwidth. In this paper, compressive sensing (CS) is applied to multichannel FM and GSM PBR to achieve improved range-Doppler resolutions and avoid some limitations of classical multiband PBR processing. In CS context, block-structured time-domain dictionary which is formed from multichannel signals suffers from coherence when fine range resolution is employed. To overcome such a pitfall, this work first transforms the dictionary to spectral domain where only the most important spectral components are retained. Principle component analysis followed by a whitening method are then applied to this spectrally transformed data in order to reduce the dimensionality of problem, thereby reducing the dictionary size and most importantly fulfilling the required condition of dictionary incoherence for better CS-based recovery. Two different block-structured dictionary formations are tested. The performance of the recovery of spatially close targets, in both FM and GSM PBR setups, are reported.