Telerobot-enabled HUB-CI model for collaborative lifecycle management of design and prototyping

The HUB-CI model is investigated in a telerobotic system in a client/server network to manage the lifecycle of engineering design and prototyping. The purpose of this platform is to support collaborative engineering design and proof of concept to enhance distributed team collaboration and resource utilization. The suggested platform is exemplified in two collaboration support tools and a physical prototyping platform. Structured Co-Insight Management is developed to support innovative idea exchanges and the consensus decision-making during the design process. Conflict/error detection management helps preventing conflicts and errors during the lifecycle of design and development. Physical collaboration over the network occurs when a team controls the telerobot operation during prototyping and testing in design cycles. A pilot system is implemented with a group project for the design of an electronic circuit (including both hardware and software designs). The functional assessment method is used to compare this platform to other collaborative design tools. The system presented offers unique qualitative advantages as an integrated collaboration support system.     

基于PLC的水泥生料配料控制系统研究

1 率值控制工艺结构 衡量生料质量的标准是水泥的三个率值．石灰石饱和系数KH、硅酸率SM、铝氧率IM，即在出磨生料中，、Fe2O3、Al2O3、SiO2诸氧化物的百分比含量必须满足以下二三式：     

Preparation of phenolic resin derived 3-D ordered macroporous carbon

Three-dimensionally ordered long-range macroporous carbon structures were prepared using commercially available phenolic resin by utilizing sacrificial colloidal silica crystalline arrays as templates that were subsequently removed by HF etching after pyrolysis in an argon atmosphere. SEM, TEM, and BET were employed to characterize the morphology and the surface area of the porous carbon structures. The pore size (150–1000 nm) and BET surface area, which reflect pore volume (298.6 m²/g (1.32 cm³/g) ∼ 93.7 m²/g (0.12 cm³/g)), of the macroporous carbon structures produced were approximately proportional to the size (150–1000 nm) of the sacrificial silica sphere templates used (annealing temp. 550°C). The achieved 550 nm porous carbon structures were examined to function as potential catalyst carriers and were successfully impregnated with Ag or Pt-Ru on their inner walls after borohydride reduction at room temperature. In addition, porous carbon patterns were fabricated using the ‘micromolding in capillary’ technique, which has potential applications in the microreaction technology.     

心理资本前因变量研究

采用心理资本问卷对分别属于医药、建筑、水利工程、电信、通讯运营和服务行业的6家企业的员工进行了调查.根据对回收的283份有效问卷的统计分析,认为员工的性别、受教育程度和所在企业的性质对员工心理资本不会产生显著性影响,而员工年龄的影响显著,50岁以上员工的总体心理资本水平高于其他年龄段员工.     

Fabrication and characterization of nano silver powder prepared by spray pyrolysis

Silver powder was fabricated by spray pyrolysis, using 2%–20% AgNO₃ solution, 336–500 mL/h flux of AgNO₃ solution, 0.28–0.32 MPa flux of carrier gas and in the 620–820 °C temperature range. The effects of furnace set temperature, concentration of AgNO₃ aqueous solution, flux of AgNO₃ aqueous solution as well as carrier gas on the morphology and particle size distribution of silver powder, were investigated. The experimental results showed that with the high concentration of AgNO₃ aqueous solution, the average grain size of silver decreased with the increasing of furnace set temperature. But the gain size distribution was not homogenous, the discontinuous grain growth occurred. With the low concentration of AgNO₃ aqueous solution, the higher furnace set temperature made the nano sliver grains sintered together to grow. Nano silver powder about 100 nm was fabricated by spray pyrolysis, using 2wt% AgNO₃ solutions, 336 mL/h flux of AgNO₃ aqueous solution, 0.32 MPa flux of carrier gas at 720 °C furnace set temperature.     

Zonal disintegration phenomenon in enclosing rock mass surrounding deep tunnels -- Elasto-plastic analysis of stress field of enclosing rock mass

The zonal disintegration phenomenon (ZDP) is a typical phenomenon in deep block rock masses. In order to investigate the mechanism of ZDP, an improved non-linear Hock-Brown strength criterion and a bi-linear constitutive model of rock mass were used to analyze the elasto-plastic stress field of the enclosing rock mass around a deep round tunnel. The radius of the plastic region and stress of the enclosing rock mass were obtained by introducing dimensionless parameters of radial distance. The results show that tunneling in deep rock mass causes a maximum stress zone to appear in the vicinity of the boundary of the elastic and the plas-tic zone in the surrounding rock mass. Under the compression of a large tangential force and a small radial force, the rock mass in the maximum stress zone was in an approximate uniaxial loading state, which could lead to a split failure in the rock mass.     

基于单片机的病房无线呼叫系统设计

为解决传统病房有线呼叫系统存在的布线复杂、易出故障、维修不便、不能在现有床位基础上及时增加新床位信息等问题,提出了无线呼叫系统设计。采用STC89C52系列单片机作为主控芯片,nRF905作为无线收发的核心芯片,并配以相应的LCD显示屏和声光报警器,设计出了无线病房呼叫系统。结果表明,该系统可靠传输距离达90 m以上,具有一定的抗干扰性,且可以临时方便增加床位显示信息,能够满足医院的临时实际需求。该系统性能稳定,操作简便,可以有效代替传统有线呼叫系统。     

Research on technology of desktop virtualization based on SPICE protocol and its improvement solutions

Increasingly mature cloud computing technology promotes virtual desktop technology, which can solve many problems existing in traditional computing models. However, virtual desktop solutions introduce the thorny problem of how to deliver a real desktop experience to users, as if they are using it locally, especially when playing video. The SPICE （simple protocol for independent computing environments） virtual desktop solution provides several image compression algorithms to address this problem with the purpose of making virtual desktops as real as possible. Although different compression algorithms can contribute their own abilities to different images to a large extent, switching between them is a big problem that consumes a large amount of resources to detect the different type of image and also causes jitter of the virtual desktop. This paper proposes a new solution, called SPICEx, using the JPEG2000 compression algorithm with dynamic compression ratios to solve the problem and finally validates that the performance is better than that of SPICE. With better quality of user experience and also reducing bandwidth consumption, SPICEx solution is meaningful in virtual desktop fields and can be widely used.     

An SVD-based adaptive robust speech steganography using MDCT coefficient

Multimedia Tools and Applications - Speech is one of the essential ways of communication. The study of speech steganography provides great value in information security. To improve imperceptibility...     

高分2号图像业务化大气校正查找表的设计与实现

为实现高分2号图像(GF2)业务化大气校正,利用矢量6S模型(6SV)将辐射传输散射与吸收进行分离计算,其中散射部分采用涵盖各种大气模式、气溶胶类型、成像几何等条件下的大气校正查找表(look-up tables,LUTs)表示,大气吸收部分采用6SV拟合计算的6种大气模式下大气透过率的经验公式表示,这种处理有效简化了查找表大小.在内存4 GB、主频3.10 GHz条件下,通过比较基于本查找表方法和基于FLAASH大气校正软件对北京地区一景GF2数据处理.结果表明:以6SV模型直接大气校正法结果作为真值,两者的绝对误差分别为0.8%和2.6%,处理时间分别为77 s和240 s,该大气校正查找表在处理精度和效率更加适合业务化大气校正.