Einlaufverhalten nasslaufender Lamellenkupplungen im Schlupfbetrieb

Forschung im Ingenieurwesen - Nasslaufende Lamellenkupplungen weisen zu Betriebsbeginn eine Phase des Einlaufens auf, in der sich das Reibungsverhalten durch Anpassung der Reibflächen...     

Influence of Methanol on Prion Reduction during High Temperature and High Pressure Oleochemical Processes

Prion‐reduction in standard biodiesel processes is caused by acidic and alkaline conditions. In the alternative RepCat biodiesel process, efficient prion‐reduction can be achieved by high‐temperature/pressure. However, a possible increase in thermostability of prions in the presence of methanol during these conditions has not previously been investigated, and is verified in this work. Samples are spiked with prions, treated with methanol, and incubated at 220 °C at 80 bar for 30 min. No traces of protease‐resistant prion protein (as proxy for prions) are detected in tallow or glycerine (as the final by‐product) after treatment. Serial dilutions of spiked prions show at least 6 log₁₀ prion reduction. More importantly, similar effects are detected using milder conditions of 200 °C at 70 bar for 15 min, representing the worst‐case conditions of the process. In conclusion, this study shows that methanol does not increase the thermostability of prions and the RepCat process can efficiently eliminate prions and is therefore safe for the usage of category 1 tallow. Practical Applications: The study further supports the applicability of RepCat process in reducing prion‐contamination in the presence of methanol. Furthermore, the conditions leads to a considerable reduction of prions in glycerine obtained as by‐product.     

National geodatabase of tidal stream power resource in USA

A geodatabase of tidal constituents is developed to present the regional assessment of tidal stream power resource in the USA. Tidal currents are numerically modeled with the Regional Ocean Modeling System (ROMS) and calibrated with the available measurements of tidal current speeds and water level surfaces. The performance of the numerical model in predicting the tidal currents and water levels is assessed by an independent validation. The geodatabase is published on a public domain via a spatial database engine with interactive tools to select, query and download the data. Regions with the maximum average kinetic power density exceeding 500 W/m² (corresponding to a current speed of ～1 m/s), total surface area larger than 0.5 km² and depth greater than 5 m are defined as hotspots and documented. The regional assessment indicates that the state of Alaska (AK) has the largest number of locations with considerably high kinetic power density, followed by, Maine (ME), Washington (WA), Oregon (OR), California (CA), New Hampshire (NH), Massachusetts (MA), New York (NY), New Jersey (NJ), North and South Carolina (NC, SC), Georgia (GA), and Florida (FL).     

The influence of third-body particles on wear rate in unicondylar knee arthroplasty: a wear simulator study with bone and cement debris

The reduced intraoperative visibility of minimally invasive implanted unicondylar knee arthroplasty makes it difficult to remove bone and cement debris, which have been reported on the surface of damaged and retrieved bearings. Therefore, the aim of this study was to analyze the influence of bone and cement particles on the wear rate of unicompartmental knee prostheses in vitro. Fixed bearing unicompartmental knee prostheses were tested using a knee-wear-simulator according to the ISO standard 14243-1:2002(E) for 5.0 million cycles. Afterwards bone debris (particle size 671 ± 262 μm) were added to the test fluid in a concentration of 5 g/l for 1.5 million cycles, followed by 1.5 million cycles blended with cement debris (particle size 644 ± 186 μm) in the same concentration. Wear rate, knee-kinematics and wear-pattern were analyzed. The wear rate reached 12.5 ± 1.0 mm³/million cycles in the running-in and decreased during the steady state phase to 4.4 ± 0.91 mm³/million cycles. Bone particles resulted in a wear rate of 3.0 ± 1.27 mm³/million cycles with no influence on the wear rate compared to the steady state phase. Cement particles, however, lead to a significantly higher wear rate (25.0 ± 16.93 mm³/million cycles) compared to the steady state phase. The careful removal of extruded cement debris during implantation may help in reducing wear rate. Bone debris are suggested to have less critical influence on the prostheses wear rate.