Analytical approach with Laplace transform to the inverse problem of one‐dimensional heat conduction transfer: Application to second and third boundary conditions

An analytical method using Laplace transformation has been developed for one‐dimensional heat conduction. This method succeeded in explicitly deriving the analytical solution by which the surface temperature for the first kind of boundary condition can be well predicted. The analytical solutions for the surface temperature and heat flux are applied to the second and third of the boundary conditions. These solutions are also found to estimate the corresponding surface conditions with a high degree of accuracy when the surface conditions smoothly change. On the other hand, when these conditions erratically change such as the first derivative of temperature with time, the accuracy of the estimation becomes slightly less than that for a smooth condition. This trend in the estimation is similar irrespective of any kind of boundary condition. © 2002 Wiley Periodicals, Inc. Heat Trans Asian Res, 32(1): 29–41, 2003; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10069     

Purification and characterization of a highly thermostable, oxygen-resistant, respiratory [NiFe]-hydrogenase from a marine, aerobic hydrogen-oxidizing bacterium Hydrogenovibrio marinus

The membrane-bound [NiFe]-hydrogenase from Hydrogenovibrio marinus (HmMBH) was purified homogeneously under anaerobic conditions. Its molecular weight was estimated as 110 kDa, consisting of a heterodimeric structure of 66 kDa and 37 kDa subunits. The purified enzyme exhibited high activity in a wide temperature range: 185 U/mg at 30 °C and 615 U/mg at 85 °C (the optimum temperature). The K_m and k_cat/K_m values for H₂ were, respectively, 12 μM and 8.58 × 10⁷ M⁻¹ s⁻¹. The optimum reaction pH was 7.8, but its stability was particularly high at pH 4.0-7.0. Results show that HmMBH was remarkably thermostable and oxygen-resistant: its half-life was 75 h at 80 °C under H₂, and more than 72 h at 4 °C under air. The air-oxidized HmMBH for 72 h showed only weak EPR signals of Ni-B, suggesting a structural feature in which the active center is not easily oxidized.     

Kinetic studies on lipase-catalyzed acetylation of 2-alkanol with vinyl acetate in organic solvent

Lipase-catalyzed acetylation of 2-alkanol with vinyl acetate has been studied kinetically using Burkholderia cepacia lipase (BCL), enantiomerically pure (R)- and (S)-2-alkanols and different organic solvents. The rate equation was derived by the steady state method for the simplified mechanism. The second order rate constants (k(R) and k(S)) for (R)- and (S)-2-alkanols were evaluated from the slopes of the double reciprocal plots, v(-1) vs. [2-alkanol](-1), where v is the initial rate of the reaction. The log k(R) value increased with the solvent hydrophobicity log P, where P is a partition coefficient of a given solvent between octanol and water. The log k(S) value also increased with log P except the bulky solvents such as 1,4-dioxane and cyclohexane, in which the rates were faster than those expected from the log k(S) vs. log P plot. The slope of log k(S) vs. log P plot was larger than that for (R)-2-alkanol. Thus, log E (E=k(R)/k(S): enantioselectivity) decreased with log P except the bulky solvents. The rate constants and the enantioselectivity were different depending on the structure (carbon number CN) of 2-alkanol. The log E vs. CN plot was minimized at CN=8 and 10 and the log k(S) vs. CN plot maximized at CN=8 and 10. In contrast the log k(R) vs. CN plot showed a different feature from the log E vs. CN plot. These facts suggest that dependence of E on CN is more strongly affected by the reactivity of (S)-2-alkanol than that of (R) isomer in this acetylation.     

A three‐phase hybrid stepping motor drive system combined with position‐sensorless closed‐loop control

This paper proposes a drive system for a three‐phase hybrid stepping motor, combining sensorless closed‐loop control with conventional open‐loop control. It is characterized by sophisticated control providing both prevention of pulling out from synchronism and suppression of natural rotor oscillation, without any position sensor attached to the motor shaft. A switching technique in chopper control which can enlarge the speed range controllable in the sensorless closed‐loop control is described. Starting and stopping sequences are developed to reduce mechanical natural oscillation produced in the transient state. Finally, the proposed drive system is compared experimentally with a conventional constant‐current open‐loop drive system. It is shown that the proposed drive system can perform the switchover from starting to sensorless closed‐loop operation within 20 ms, and can reduce the natural oscillation caused just after positioning. © 2000 Scripta Technica, Electr Eng Jpn, 131(3): 80–90, 2000     

Control schemes and transient characteristics of a high‐speed phase shifter for power flow control in power transmission systems

In recent years, attention has been paid to the concept of FACTS (Flexible AC Transmission Systems), along with significant progress in power electronic technology. A high‐speed phase shifter, which is one of the most promising devices in the FACTS concept, has the potential of power flow control and/or voltage stability in power transmission systems. In this paper, theory and experiment reveal that conventional high‐speed phase shifters may cause power swings in a transient state as a result of coupling between instantaneous active and reactive power control loops. Thus, two new control schemes for a high‐speed phase shifter are proposed to achieve both power flow control and power swing damping. The second proposed control scheme is based on the control scheme of an already proposed series active filter. Simulated and experimental results agree well with analytical results, not only in steady states but also in transient states. © 1999 Scripta Technica, Electr Eng Jpn, 128(2): 74–82, 1999     

X-ray Diffraction Analysis to Explore Molecular Traces of Eccentric Contraction on Rat Skeletal Muscle Parallelly Evaluated with Signal Protein Phosphorylation Levels

We performed X-ray diffraction analyses on rat plantaris muscle to determine if there are strain-specific structural changes at the molecular level after eccentric contraction (ECC). ECC was elicited in situ by supramaximal electrical stimulation through the tibial nerve. One hour after a series of ECC sessions, the structural changes that remained in the sarcomere were evaluated using X-ray diffraction. Proteins involved in cell signaling pathways in the muscle were also examined. ECC elicited by 100, 75, and 50 Hz stimulation respectively developed peak tension of 1.34, 1.12 and 0.79 times the isometric maximal tetanus tension. The series of ECC sessions phosphorylated the forkhead box O proteins (FoxO) in a tension-time integral-dependent manner, as well as phosphorylated the mitogen-activated protein kinases (MAPK) and a protein in the mammalian target of rapamycin (mTOR) pathway in a maximal tension dependent manner. Compared to isometric contractions, ECC was more efficient in phosphorylating the signaling proteins. X-ray diffraction revealed that the myofilament lattice was preserved even after intense ECC stimulation at 100 Hz. Additionally, ECC < 75 Hz preserved the molecular alignment of myoproteins along the myofilaments, while 75-Hz stimulation induced a slight but significant decrease in the intensity of meridional troponin reflection at 1/38 nm⁻¹, and of myosin reflection at 1/14.4 nm⁻¹. These two reflections demonstrated no appreciable decrease with triple repetitions of the standard series of ECC sessions at 50 Hz, suggesting that the intensity decrease depended on the instantaneous maximal tension development rather than the total load of contraction, and was more likely linked with the phosphorylation of MAPK and mTOR signaling proteins.     

Microstructure Control of Thermally Sprayed Co-Based Self-Fluxing Alloy Coatings by Diffusion Treatment

This article describes microstructure control aimed for wear-resistance improvement of Co-based (Co-Cr-W-B-Si) self-fluxing alloy coating by diffusion treatment. The diffusion treatments of thermally sprayed Co-based self-fluxing alloy coating on steel substrate were carried out at 1370-1450 K for 600-6000 s under an Ar gas atmosphere. Microstructural variations of the coating and the interface between the substrate and the coating were investigated in detail. A proper diffusion treatment precipitates two kinds of fine compounds in Co-based matrix. X-ray diffractometer (XRD) and electron probe microanalyzer (EPMA) analysis revealed these precipitates to be a chromium boride dissolving cobalt and a tungsten boride containing cobalt and chromium. The size of each precipitate became larger with increasing treatment temperature and time. A coating with the proper size borides showed a superior wear-resistance. This article is an invited paper selected from presentations at the 2007 International Thermal Spray Conference and has been expanded from the original presentation. It is simultaneously published in Global Coating Solutions, Proceedings of the 2007 International Thermal Spray Conference, Beijing, China, May 14-16, 2007, Basil R. Marple, Margaret M. Hyland, Yuk-Chiu Lau, Chang-Jiu Li, Rogerio S. Lima, and Ghislain Montavon, Ed., ASM International, Materials Park, OH, 2007.     

Enrichment of arachidonic acid: Selective hydrolysis of a single-cell oil fromMortierella withCandida cylindracea lipase

Three lipases, isolated previously in our laboratory, and a known lipase fromCandida cylindracea were screened for the enrichment of arachidonic acid (AA). The enzyme fromC. cylindracea was the most effective for the production of oil with high concentration of AA. When a single-cell oil fromMortierella alpina, containing 25% AA, was hydrolyzed with this lipase for 16 h at 35°C, the resulting glycerides contained 50% AA at 52% hydrolysis. After this, no further hydrolysis occurred, even with additional lipase. However, when the glycerides were extracted from the hydrolyzate and were hydrolyzed again with new lipase, the resulting oil contained 60% AA, with a recovery of 75% of its initial AA content. Triglycerides were the main components of the resulting oil. The release of each fatty acid from the oil depended on the hydrolysis rate of its ester. The fatty acid, whose ester is the poorest substrate for the enzyme, is concentrated in the glycerides.     

Transient analysis of the release and reduction of NOx using a Pt/Ba/Al2O3 catalyst

The release and reduction of NO_x in a NO_x storage-reduction (NSR) catalyst were studied with a transient reaction analysis in the millisecond range, which was made possible by the combination of pulsed injection of gases and time resolved time-of-flight mass spectrometry. After an O₂ pulse and a subsequent NO pulse were injected into a pellet of the Pt/Ba/Al₂O₃ catalyst, the time profiles of several gas products, NO, N₂, NH₃ and H₂O, were obtained as a result of the release and reduction of NO_x caused by H₂ injection. Comparing the time profiles in another analysis, which were obtained using a model catalyst consisting of a flat 5 nmPt/Ba(NO₃)₂/cordierite plate, the release and reduction of NO_x on Pt/Ba/Al₂O₃ catalyst that stored NO_x took the following two steps; in the first step NO molecules were released from Ba and in the second step the released NO was reduced into N₂ by H₂ pulse injection. When this H₂ pulse was injected in a large amount, NO was reduced to NH₃ instead of N₂.

A only small amount of H₂O was detected because of the strong affinity for alumina support. We can analyze the NO_x regeneration process to separate two steps of the NO_x release and reduction by a detailed analysis of the time profiles using a two-step reaction model. From the result of the analysis, it is found that the rate constant for NO_x release increased as temperature increase.     

Random exchanges of non-conserved amino acid residues among four parental termite cellulases by family shuffling improved thermostability

There have been two major problems preventing applications of termite cellulases; one was difficulty for their hetelologous overexpression, and another is their low thermostability. We previously achieved adaptation of termite cellulase genes to an overexpression system of Escherichia coli by family shuffling of four orthologous cDNAs (Biosci. Biotechnol. Biochem., 2005; 69: 1711-1720). Using the adapted mutant cDNAs as parental genes combined with native-form cDNAs, we performed further family shuffling and obtained mutant cDNAs, which gave enzymes with improved thermostability. The best-evolved clone (PA68) was improved by 10 degrees C in maximum stability (retaining 90% original activity for 30 min incubation) from the parental enzymes, and kept 54% of its original activity for 150 min at 50 degrees C, whereas the most thermostable enzyme amongst the parents (A18) retained 30% of its original activity. PA68 showed 889 (micromoles of reducing sugars/min/mg of protein) in V(max) and 560 (micromoles of reducing sugars/min/mg of protein) in the specific activity against carboxymethylcellulose, which corresponds to 9.8 and 13.1 times of those of one of the ancestral enzymes rRsEG. In summary, we improved thermostability of the termite cellulase and increased the V(max) value and specific activity by combining only cDNAs encoding enzymes adapted for normal temperatures.