Deformation Behavior of Polycrystalline Aluminum Oxide

The steady-state creep behavior of polycrystalline aluminum oxide from 97 to 100% dense has been examined at temperatures from 1600° to 1800°C over a range of stresses from 100 to 2000 psi under four-point transverse bending. Grain size is shown to have an important effect on the deformation behavior. Stress-strain rate dependence for the fine-grained aluminum oxide (3 to 13μ) is of viscous behavior (°_ε∼σ). The strain rate is also inversely proportional to the square of the grain size (°_ε∼ 1/(GS)²). The creep behavior can be described by the Nabarro-Herring diffusional flow model although the diffusion coefficient does not agree with that for oxygen diffusion in sapphire. When the grain size becomes coarse, the Nabarro-Herring model no longer applies. Coarse-grained aluminum oxide (50 to 100μl) behaves plastically when deformed (°_ε∼σ). The strain rates observed on coarsegrained aluminum oxide are higher than one would predict from the deformation behavior of fine-grained aluminum oxide. This plastic flow probably occurs through some dislocation movement or glide mechanism.     

Investigation of Taimyrsk graphites for producing periclase-carbon ladle refractories

Conclusions The investigations showed that Taimyrsk graphite corresponds in chemical composition to foundry and crucible graphite.The content of crystalline graphite equals 13.0–26.3%. The characteristics of periclase carbon goods based on foundry and Taimyrsk graphites correspond to the demands placed on ladle refractories. The wear factors of these products in the slag belt of the lining of 350-tonne steel ladles are on practically the same level.Taimyrsk graphites may be used for the production of periclase-carbon ladle refractories in place of crucible or foundry graphite.L. N. Kurlyandskaya (Urals Geology Planning Association) and L. Ya. Osipova (All-Union Institute of Refractories) took part in this research.Translated from Ogneupory, No. 1, pp. 15–17, January, 1991.     

Settling velocities of particles in bubbly gas-liquid mixtures

The axial dispersion-sedimentation model is commonly used to describe the axial concentrations of solids in three phase bubble columns at low liquid velocities. When the two parameters of this model, the particle settling velocity and the solids axial dispersion coefficient, are uncoupled by the use of various assumptions, physically unrealistic values of these parameters often result. Direct experimental measurements of solids settling rates in bubbly gas-liquid mixtures were carried out. The measured mean settling velocities decreased slightly with gas flow rate and were equal to or slightly less than the single particle free settling velocity in the liquid alone. Solids axial dispersion coefficients were also obtained from the solids settling rate distribution data, and gave values considerably less than the experimental liquid axial dispersion coefficient.     

A geometric solution to the largest-free-sphere problem in zeolite frameworks

We have applied Delaunay triangulation to models of the known zeolite frameworks. We show that this well-established technique from computational geometry provides for each framework; (i) the location and shape of the open pores and channels, (ii) the diameter of the largest possible included sphere, and indirectly (iii) the diameter of the largest-free-sphere that can diffuse through the framework by at least one lattice translation. Since Delaunay triangulation naturally locates the empty spaces within a set of points, it provides a powerful computer-automated tool for determining the physical characteristics of pores and channels of zeolite frameworks. Such tools will further enhance the usefulness of large databases of hypothetical framework materials.

Here, we tabulate results for the 165 zeolite frameworks that are presently listed in the Atlas of Zeolite Frameworks. Of the known zeolites, refined as pure silicates, the largest included sphere occurs in the TSC framework, with a diameter of 16.39 Å. The largest-free-sphere has a diameter of 11.33 Å, for diffusion along the [0 0 1] direction in the VFI framework.     

Design and characterization of a multistage,mechanically stirred column absorber

A multistage, mechanically stirred column absorber has been designed and built with a modular construction, based on preliminary experiments with a test column. The column has been characterized as a gas-liquid contactor by its gas holdup, gas and liquid axial dispersion, mixing times, oxygen transfer coefficients and power consumptions, determined as a function of gas velocity, liquid velocity and impeller speed for one and two impellers per stage.Gassed power was correlated with ungassed power, gas rate and impeller speed. The gas phase axial mixing was essentially plug flow and the liquid phase axial mixing varied between 5 and 12 equivalent stages.Oxygen transfer coefficients were correlated with power consumptions and aeration rates by the equation K_La γ (P/V)^a(υ_sg)^b. The oxygen transfer coefficients with single stiffer stages were 25% above those for the double stirrer stages for equal power consumption and gas rates. Except for the low aeration and high power consumption extremes, the column showed superior oxygen transfer performance. in comparison to tubular loop and tank fermenters.     

GRAPHICAL SOLUTION OF MULTISTAGE FLUIDIZED BED HEAT EXCHANGER

The design of multistage fluidized beds for heat exchange necessitates the solution of the mass and energy balance equations combined with the equilibrium relations for each stage. This paper presents a novel way of applying well known methodology to a different technology, one where it has not been widely applied.

In the present work a McCabe-Thiele type of graphical approach is presented for both counter-current and cross-current contacting multiple fluidized beds. The necessary equations for a multistage calciner are developed and the application of the proposed method is demonstrated. Generalized fluidized bed efficiency for counter-current and cross-current multiple fluidized bed is presented.     

Stress-Induced Transformation and Plastic Deformation for Y2O3-Containing Tetragonal Zirconia Polycrystals

Yttria-containing tetragonal zirconia polycrystals with low thermal stability showed plastic deformation with a maximum bending strain of 0.8% due to the stress-induced tetragonal to monoclinic transformation. The strain rate depended on applied stress and temperature. The temperature at which the transformation rate is maximum increases with increasing applied stress. Changes in microstructure and crystallographic structure after plastic deformation were examined by transmission electron microscopy and X-ray analyses. The mechanism of plastic deformation is discussed in relation to the tetragonal to monoclinic transformation.     

Effect of diethylene glycol content and annealing temperature on the structure and properties of poly(ethylene terephthalate)

The effect of 2,2′-oxydiethanol (diethylene glycol, DEG) content (ranging from 2 to 15 mol %) and of the annealing temperature (in the range from 100 to 260°C) on the density, calorimetric, dynamic- and static-mechanical and small angle X-ray scattering (SAXS) behavior of undrawn and drawn samples (granules, films, and bristles) of poly(ethylene terephthalate) (PET) has been studied. The known dependences on the annealing temperature are confirmed. Some discrepancies with earlier investigations of the dependences on the DEG content are established: constant values for the SAXS intensity and long spacing, for the lamellar thickness and for the volume fraction crystallinity a_c. These discrepancies are explained by the variation of the glass transition temperature (T_g) and melting temperature (T_m) of the materials with different DEG contents. The previous hypothesis of the segregation of the comonomer (DEG) units into the amorphous regions is confirmed.     

Analysis of polymer blend morphology by transmission and reflection light scattering techniques

Optical inspection is a potentially powerful and practical tool to collect information on polymer blend morphology for on-line quality and process control. This paper describes two approaches for the characterization of polymer blend materials by multiple light scattering. A quantitative evaluation of spectral turbidimetry (scattering of transmitted light) is presented and an adaptation of this technique for monitoring particle size, independent of the volume fraction is demonstrated. Such a procedure is applicable to materials in film form. A different approach is presented for the analysis of nearly spherical particles in optically thick samples: the diffuse reflection pattern surrounding the position of incidence of a focused light beam on the surface of the turbid medium is scanned by a single side imaging system. A spectral pseudo-transmittance signal processing technique provides particle size information again independent of the volume fraction: Both techniques have been tested using well characterized polystyrene microspheres suspended in water as well as poly(methyl) (methacrylate)/polystyrene polymer blends.