Effect of beam voltage on the properties of aluminium nitride prepared by ion beam assisted deposition

The effects of nitrogen-beam voltage on the structure, stress, energy band gap and hardness of AIN thin films deposited on Si (111), Si (100) and sapphire (0001) by ion beam assisted deposition (IBAD) are reported. As the nitrogen-beam voltage was increased from 50 to 200 V, the stress and disorder in the AIN films increased as determined by X-ray diffraction, FTIR and Raman spectroscopy. The preferred orientation of the film's c-axis changed from completely normal to the film at 100 V, to a mixture of normal and in the plane of the film at 200 V. For AIN films deposited under the same conditions, the films were more highly oriented on sapphire (0001) than in Si (111). The hardness of the films increased from 18.2 to 23.7 GPa with the nitrogen-beam voltage, and possible reasons for this change in hardness are considered.     

Unique ESD failure mechanisms during negative to Vcc HBM tests

HBM ESD tests on two types of 0.6 μm DRAM devices showed that internal circuit or output driver failures would occur after the input or I/O pins were ESD stressed negative with respect to Vcc at ground. These failures occurred at lower than expected ESD stress voltages due to power-up circuit interactions that either turned-on unique internal parasitic ESD current paths or disrupted the normal operation of the output pin’s ESD protection circuit. ESD analysis found there exists a set of power-up sensitive circuits and if placed near a Vcc bond pad can result in low voltage ESD failures.     

The systemic inflammatory response to cardiopulmonary bypass and the brain

The acquired immune deficiency syndrome (AIDS) is a lethal multisystem disease. Its ocular manifestations have received relatively little attention in the literature. Between 73% and 100% of AIDS patients develop ocular lesions. The commonest lesions seen are retinal--either infectious or noninfectious retinopathy. Involvement of the conjunctiva with Kaposi's sarcoma, infected tears and infected cornea as well as the vitreous are less common. Infections with cytomegalovirus and varicella zoster virus are common causes of visual loss and can be treated with antiviral agents such as ganciclovir and foscarnet. This greatly increases the quality of life in these patients by preventing visual loss.     

Performance characteristics of a composite multivariate quality control system.

We present the results of an evaluation of the performance characteristics of a composite multivariate quality control (CMQC) system that incorporates quality control rules for univariate, multivariate, and correlation conditions. The CMQC system evaluated is designed to help analysts detect unacceptable trends and systematic error in one or more variables, unacceptable random error in one or more variables, and unacceptable changes in the correlation structure of any pair of variables. It is also designed to be tolerant of missing data, to allow analysts to reject as few as one or as many as all variables in a run, and to provide analysts with control statistics and graphics that logically relate to sources of analytical error. We show that the various components of the CMQC system have adequate statistical power to detect systematic errors, random errors, and correlation changes under the conditions likely to be encountered with multivariate analytical measurement systems: (1) a single variable with increased systematic or random error; (2) all variables or a subgroup of variables affected by a common problem that increases systematic or random error; and (3) missing data for one or more variables in a run. We also show that the power of the multivariate component of the CMQC system to detect systematic and random errors is higher than the power of an alternative multivariate test criterion.     

Accelerated aging of extruded dielectric power cables. I. Controland monitoring methodology

An improved accelerated cable life test is described. Through the use of programmable logic controllers (PLCs), very precise and consistent control of the accelerated aging process has been achieved. A computer has been utilized to make continuous real-time acquisition and storage of key operating parameters possible. This precise control and monitoring methodology has permitted the study of the synergistic effects of voltage and temperature on the accelerated aging of full-sized cables in the laboratory     

A STUDY OF SUPERIMPOSED FRACTURE MODES I, II AND III ON PMMA

A test apparatus has been developed to study the fracture behaviour of engineering materials subjected to superimposed tensile and shear (Mode I and II) loads using a single edge notch specimen. Stress intensity factors were calculated using finite element analysis. Test results for PMMA are reported. Results from circumferentially notched round bar specimens, subjected to combined tension and torsion (Mode I and III) loading are also reported. The Mode I/II results are consistent with the mixed mode fracture response of a wide range of brittle materials, although there is some evidence of non-linear behaviour. The fracture behaviour for superimposed Modes I and III indicates the strong influence of non-linear deformation which causes the mixed mode toughness to be dependent on the sequence and type of loading.     

The concept of an endurance limit for adhesive joints

The effect of cyclic stressing on the strength of single lap adhesive joints has been studied and a considerable reduction in strength observed when the maximum stress exceeds about 40% of the ultimate tensile strength, but whether or not a true endurance limit exists is not proven. Fallacies are shown in some of the techniques which have been proposed for studying the fatigue behaviour of adhesive joints.     

The use of Schottky barrier diodes for the detection of surface contamination and damage in the fabrication of GaAs MESFETS

The gates of GaAs MESFETS rely on the formation of a Schottky diode between the semiconductor surface and a deposited metal and so are extremely sensitive to the nature of this interface. For this reason an investigation of surface damage and contamination by the various processing stages involved in IC fabrication has been undertaken. This paper outlines the results obtained from processes involved in activation of ion implantation through annealing with a dielectric encapsulant, wet chemical etching, and metallization. Methods for removing or minimizing the effects of processing damage or contamination are also investigated.     

Perceived risk for influenza in veterans with spinal cord injuries and disorders.

Objective: Guided by the extended parallel process model (EPPM), the objective was to assess control processes dominant in influenza behavior decisions. Design: Cross-sectional survey. Results: Response rate was 31% (n=968). Regarding influenza risk, 59% were in danger control. Those in fear control were more likely to report influenza infection (p=.000). In the nonvaccinated, those in fear control were more likely to indicate not knowing where to get the vaccine (p=.016) and that it was unavailable (p=.027), and those in danger control believed they did not need it (p=.023). Zero critical values were more likely to indicate that no health provider recommended the shot (p=.002). Conclusions: Most perceived efficacy to be stronger than threat related to influenza; according to the EPPM, they are aware of their risk but recognize their ability to avert it. For those in danger control, messages should focus on increasing perceptions of severity and susceptibility to positively affect behavior change. For those in fear control, messages should focus on efficacy only. With a critical value of zero, no threat is induced, and a high-threat/high-efficacy approach should be taken. (PsycINFO Database Record (c) 2010 APA, all rights reserved)