Effect of wall slip on blown film thickness distribution

One of the most important materials for blown film is high‐density polyethylene (HDPE) with wide molecular weight distribution. First, we computed a wall stress at the entrance of a spiral groove in a particular die during blown film processing on a particular condition, to which a similar condition is widely utilized in a film works. The computed value is about 170 kPa, while the HDPE melt slips at die wall at stresses above approximately 50 kPa. The stress of 170 kPa is sufficiently large for the slip occurrence of the melt. Then, we investigated the effects of wall slip and melt visosity on film thickness distribution in the circumferential direction; the distribution tends to decrease with decreasing wall slip and melt viscosity. This tendency is explained by considering flow distribution in a spiral mandrel die and polymer melt flow characteristics.     

Suppression of Active Oxidation of Polycarbosilane-Derived Silicon Carbide Fibers by Preoxidation at High Oxygen Pressure

Three types of polycarbosilane-derived SiC fibers (Nicalon, Hi-Nicalon, and Hi-Nicalon S) with different SiO₂ film thicknesses ( b ) were subjected to exposure tests at 1773 K in an argon-oxygen gas mixture with an oxygen partial pressure of 1 Pa. The suppression effect of a SiO₂ coating on active oxidation was examined through TG, XRD analysis, SEM observation, and tensile tests. All the as-received fibers were oxidized in the active-oxidation regime. The mass gain and the SiO₂ film development showed a suppression of active oxidation at b values of ≧0.070 μm for Nicalon, ≧0.013 μm for Hi-Nicalon, and ≧0.010 μm for Hi-Nicalon S fibers. Considerable strength was retained in the SiO₂-coated fibers. For Hi-Nicalon fibers, the retained strength was 71%–90% of the strength in the as-received state (2.14–2.69 GPa).     

Interfacial Reaction Between Cu Substrates and Zn-Al Base High-Temperature Pb-Free Solders

Chemical reactions between Cu substrates and Zn-Al high-temperature solder alloys, Zn-4Al and Zn-4Al-1Cu (mass%), at temperatures ranging from 420°C to 530°C were experimentally investigated by a scanning electron microscope using backscattered electrons (SEM-BSE) and an electron probe microanalyzer (EPMA). Intermediate phases (IMPs), β(A2) or β′(B2), γ(D8₂), and ε(A3) phases formed and grew during the soldering and aging treatments. The consumption rate of the IMP for Cu substrates is described by the square root of t in both the alloys, while the additional Cu in the molten Zn-Al alloy slightly suppresses the consumption of Cu substrates. The growth of IMPs during soldering treatment is controlled by the volume diffusion of constituent elements, and its activation energy increases in the order of Q _ε < Q _γ < Q _β. In view of the aging process, the growth of IMPs is considered to be controlled by the volume diffusion. In particular, the layer thickness of γ rapidly grows over 200°C, although the thickness of the β layer grows very slowly.     

Phase Equilibria and Phase Transition of the Ni–Fe–Ga Ferromagnetic Shape Memory Alloy System

Phase equilibria and martensitic and magnetic transitions of the β (B2 and L2₁) phase in the Ni–Fe–Ga system were investigated. The b phase was found to be in equilibrium with the γ (A1 structure) or γ′ (L1₂ structure) phase. The Curie temperature, T _c , equilibrium temperature, T _o 5 (Ms + Af)/2, martensitic transition starting temperature, M _s , and reverse transition finishing temperature, Af , of the β single–phase alloys were sensitive to the Fe and Ga compositions. The Fe substitution for Ni decreased and increased the T _o and T _c , respectively. The Ga substitution for Ni or Fe decreased both the T _o and T _c . The entropy change accompanying the reverse martensitic transition showed compositional dependence due to the magnetic contribution. The saturation magnetization I _s of the Ni–Fe–Ga system showed a strong dependence on the magnetic valence Z _M . The Is values of the Ni–Fe–Ga alloys annealed at 1023 K showed the same Z _m dependence as other ferromagnetic shape memory alloy (FSMA) systems. This article is based on a presentation made in the symposium entitled "Phase Transformations in Magnetic Materials," which occurred during the TMS Annual Meeting, March 12-16, 2006, in San Antonio, Texas, under the auspices of the Joint TMS–MPMD and ASMI–MSCTS Phase Transformations Committee.     

Uniaxial elongational viscosity of various molten polymer composites

Uniaxial elongational viscosity of low density polyethylene (LDPE) that was filled with glass bead, glass flake, talc, or glass fiber was measured. The effect of various inorganic fillers on the strain-hardening property in elongational viscosity was investigated. The strain-hardening property of LDPE became weaker by the addition of fillers in the order of glass bead, glass flake, and talc. Glass fiber filled LDPE showed a strain-softening property. The smaller the particle and the larger the aspect ratio, the weaker the strain-hardening property. Their causes were analyzed from the two terms, i.e., the relaxation spectrum and the damping function, by Bernstein-Kearsley-Zapas (BKZ) model. By the incorporation of fillers, the relaxation modules became larger, and the damping function became stronger in the order of glass bead, glass flake, talc, and glass fiber. Recoverable strain was also measured to understand weaker strain-hardening properties. The degree of recovery became smaller by the addition of fillers. It was found that the smaller the particles and the larger the aspect ratio, the smaller the degree of recovery. It was concluded that weaker strain-hardening properties of LDPE composite than that of LDPE are caused by stronger damping function and smaller degree of recovery.     

High-melt-strength polypropylene with electron beam irradiation in the presence of polyfunctional monomers

High-melt-strength polypropylene (PP) was achieved with irradiation by an electron beam generated from an accelerator in the presence of polyfunctional monomers (PFM). Among 16 PFMs, the relatively shorter molecular chain bifunctional monomers such as 1,4-butanediol diacrylate (BDDA) and 1,6-hexanediol diacrylate (HDDA) were the most effective for enhancing the melt strength of PP. The concentration and dose of the HDDA to obtain the high melt strength PP in irradiation under nitrogen gas atmosphere were 1.5 mmol/100 g PP and 1 kGy, respectively. DSC measurement and dynamic mechanical analysis showed that the thermal behavior of the high-melt-strength PP was different from that of the original PP. Crystallinity and crystallization temperature during cooling after heating were lower and higher in high melt strength PP than original PP, respectively. Elongational viscosity at 180°C of the high-melt-strength PP showed a remarkable increase at a certain elongational time with constant strain rate, demonstrating the typical property of high-melt-strength samples. This implies that a few higher molecular chains of PP, formed by intermolecular combination of its chain by HDDA in irradiation, give higher melt strength to induce entanglement of molecular chains. © 1996 John Wiley & Sons, Inc.     

Co-Al基三元系中B2相的溶解度间隙与稳定性

Information on phase equilibria in the Co-Al based systems which are related to some magnetic and heat resistance materials is important for their microstructural control. Recently, it was proposed with a theoretical calculation on electronic band structure that some Heusler-type alloys Co2 XAl (X: Cr and Mn) should be a new type of spinelectronic materials so-called half-metallic ferromagnet. In the case of the Co2CrAl, however, magnetic properties expected from the theoretical work can not been experimentally obtained and the reason has been still unknown. On the other hand, a tunne- ling magnetoresistance (TMR) effect due to the half-metallic properties was reported in Co2 (Cr0.6 Fe0.4 ) Al alloy, but not the Co2CrAl alloy. In the present paper, it is reported that this discrepancy with the theoretical work in the Co2CrAl alloy is bought about by phase separation between A2 and B2 phases, and that the substitution of Fe for Cr can suppress the precipitation of A2 phase in the B2 phase. Such a phase separation is originally due to the miscibility gap between CoAl and Cr formed in the Co-Al-Cr ternary system as well as that reported by Hao et al. in the Ni-Co-Al-Fe system.     

Amorphous nanosilicas induce consumptive coagulopathy after systemic exposure

We previously reported that well-dispersed amorphous nanosilicas with particle size 70 nm (nSP70) penetrate skin and produce systemic exposure after topical application. These findings underscore the need to examine biological effects after systemic exposure to nanosilicas. The present study was designed to examine the biological effects. BALB/c mice were intravenously injected with amorphous nanosilicas of sizes 70, 100, 300, 1000 nm and then assessed for survival, blood biochemistry, and coagulation. As a result, injection of nSP70 caused fatal toxicity, liver damage, and platelet depletion, suggesting that nSP70 caused consumptive coagulopathy. Additionally, nSP70 exerts procoagulant activity in vitro associated with an increase in specific surface area, which increases as diameter reduces. In contrast, nSP70-mediated procoagulant activity was absent in factor XII-deficient plasma. Collectively, we revealed that interaction between nSP70 and intrinsic coagulation factors such as factor XII, were deeply related to nSP70-induced harmful effects. In other words, it is suggested that if interaction between nSP70 and coagulation factors can be suppressed, nSP70-induced harmful effects may be avoided. These results would provide useful information for ensuring the safety of nanomaterials (NMs) and open new frontiers in biological fields by the use of NMs.     

Synergistic effect of D-glucose and epidermal growth factor display on dynamic behaviors of human epithelial cells

We investigated the synergistic effect of D-glucose and epidermal growth factor (EGF) display on the dynamic cellular behaviors of morphology and migration in a culture of human epithelial cells. The time-lapse observation revealed that the cells on the D-glucose/EGF-displayed substrate were endowed with enhanced migration, accompanied with periodic changes in morphology between round and stretched shapes. Immunofluorescence staining of phosphotyrosine PY20 and vinculin was conducted to determine the intracellular localization of phosphorylated tyrosine expression and focal contact formation, respectively. On the substrate displaying D-glucose and EGF, the cells exhibited increases in the levels of the expression of phosphorylated tyrosine and the formation of focal contacts not only at the cellular periphery but also in the cell body. These findings supported the consideration that the displayed D-glucose causes the cells to be in close contact with the surface via grasping glucose transporters on the cytoplasmic membrane.     

Phase Equilibria in Ni Rich Region of Ni-Al-Fe System

The phase equilibria between γ, α, γ' and β in the Ni-rich region of the Ni-Al-Fe system were investigated by the diffusion couple method and thermodynamic models. The thermodynamic parameters were assessed based on experimental results and thermodynamic data. Moreover, the system's phase equilibria from 900 to 1 300℃ were calculated with regular solution and sublattice models, and it is shown that the theoretic results agree well with experimental phase diagram data.