A test for the statistical significance of DNA sequence similarities for application in databank searches

A method is developed, based on word-searching, which provides a rapid test for the statistical significance of DNA sequence similarities for use in databank searching. The method makes allowance for the lengths and dinucleotide compositions of the sequences being compared. A way is also described to calculate the power of the test, i.e. the probability of detecting a given similarity as being statistically significant. The effects on the power of the test of the scoring method, word length, sequence length, and sequence composition are examined. A novel scoring method is shown to be superior to the method currently used in most word-searching algorithms.     

Modelling biological processes under anaerobic conditions through integrating titrimetric and off-gas measurements-applied to EBPR systems.

An innovative method for modelling biological processes under anaerobic conditions is presented and discussed. The method is based on titrimetric and off-gas measurements. Titrimetric data is recorded as the addition rate of hydroxyl ions or protons that is required to maintain pH in a bioreactor at a constant level. An off-gas analysis arrangement measures, among other things, the transfer rate of carbon dioxide. The integration of these signals results in a continuous signal which is solely related to the biological reactions. When coupled with a mathematical model of the biological reactions, the signal allows a detailed characterisation of these reactions, which would otherwise be difficult to achieve. Two applications of the method to the enhanced biological phosphorus removal processes are presented and discussed to demonstrate the principle and effectiveness of the method.     

Emission of trace toxic metals during pulverized fuel combustion of Czech coals

A study of the trace elements emission (As, Se, Cd, Co, Cr, Cu, Zn, Hg, Tl, Pb, Ni, Sn, Sb, V, Mn and Fe) from pulverized coal combustion has been made at six heating and power stations situated in the Czech Republic. The amount of chlorine in coal has considerable influence on volatilization of some elements such as Zn, Cu, Pb, Hg and Tl, which is explained by the formation of thermodynamically stable compounds of these elements with chlorine. Generally, the affinities for Cl follows the order Tl > Cu > Zn > Pb > Co > Mn > Sn > Hg. The experimental data indicates enrichment of some of the trace toxic elements in the emissions (Cu, Zn, As, Se, Cd, Sn, Sb, Hg and Pb) and good agreement was obtained by thermodynamic equilibrium calculations with a few exceptions. In the case of Fe, Mn, Co, Cr and Sn calculated values are overestimated in the bottom ash and there are zero predicted amounts of these elements in the fly ash. In comparison, the results from experiments show up to 80% of these elements retained in fly ash. This implies that there exist additional steps leading to the enrichment by Fe, Mn, Co, Cr and Sn of small particles. Such mechanisms could include the ejection during devolatilization of small inorganic particles from the coal of bottom ash particles, or disintegration of the char containing these metals to small particles of fly ash. On the other hand, there are slightly overestimated or similar values of relative enrichment factors for As, V, Cu, Cd, Sb, Tl and Pb in the fly ashes and zero predicted values for bottom ashes. Our experimental results show about 5% or less of these elements are retained in bottom ashes, so they probably remain in the bottom ash inside unburned parts of coal. Copyright © 2003 John Wiley & Sons, Ltd.     

Numerical solution for shape optimization of an impactor penetrating into a semi-infinite target

The shape of the impactor with the maximum depth of penetration (DOP) for a given impact velocity is found using a numerical procedure for solving a corresponding non-classical variational problem. It is shown that the optimum shape in a general case is close to a blunt cone. The variation of the optimal shape of the impactor and the dependence of the DOP vs. the initial (impact) velocity and friction coefficient is studied. The analysis is performed also for optimal conical impactors.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

Erosion und Korrosion of metallischer Werkstoffe in feststoffhaltigen Wässern

Erosion and corrosion of metallic materials in particle containing aqueous solutions The combined effect and mutual influence, respectively, of erosion and corrosion of metallic materials in particle containing flows was investigated. Materials under investigation are carbon steel of different hardness levels, ferritic chromium steel, austenitic stainless steel and brass. Corrosive medium was deionized water, acid (pH 4.5), alkaline (pH 10) and chloride (3% NaCl) solution. Quartz particles were used as abrasive at various particle concentrations, grain sizes and flow velocities. For comparison, tests were performed with pure water and under conditions of idle corrosion. Mechanical or corrosive influences dominate depending on material and test conditions, in some cases, synergistic effects of both mechanisms cause an increased mass loss.     

Mechanism of the skeletal isomerisation of linear butenes over ferrierite: analysis of side reactions

An investigation of the effect of reaction conditions on product distribution in the skeletal isomerisation reaction of linear butenes has been carried out. The main reaction routes over ferrierite have been identified. Beside the main product isobutene, major by-product formation occurs. The unwanted reactions include dimerisation of butene to form octenes, hydrogen transfer yielding small amounts of saturated C₃ and C₄ hydrocarbons and disproportionation producing propene and pentenes. The most abundant by-products were pentene and propene, though these were not formed in equimolar amounts as could be expected. Oligomerisation experiments of propene over ferrierite produced large amounts of butene and pentene, revealing the presence of adsorbed nonene. The cracking of this surface species to hexene and propene is the most likely reaction route for the excess propene formation. This additional path to propene formation operates mainly at temperatures above 623 K.     

Failure loads for notched graphite/epoxy laminates with a softening strip

The strengths of two graphite/epoxy notched laminate systems with a softening strip were investigated. The softening strip was created by replacing the 0°-graphite/epoxy plies by a glass/epoxy composite. Experimental results indicated that the use of softening strips could significantly increase the laminate strength. Analysis was performed with finite elements developed using the classical laminated plate theory and was shown to be adequate. A simple point-stress failure criterion was used to predict the strength of notched laminates with softening strips and the result was found to be satisfactory.